Log in

View Full Version : Electrical I think I found the source of my no-start problem...



Farrar
03-03-2013, 01:25 PM
As long as a year ago, I started having intermittent trouble starting the engine from the key. Before long, the intermittent problem became a constant one.

Although I was still able to start the engine by turning the key to "on" and jumping the starter motor directly, it's a real pain to do.

I decided to leave that problem aside while I garaged the car for some serious interior work.

While tidying up the electrical compartment, I noticed that the red/white wire from the start inhibit relay (not the one which comes from the ignition switch) had been replaced with a blue wire, which disappeared behind the rear carpet piece. I removed the rear carpet piece and found where the blue wire goes:

16935

To the red/white wire which is supposed to be used in the first place!

There is some evidence of overheating in the electrical compartment -- melted insulation covered with electrical tape, and deformed relay sockets. These have now been taken care of.

To make sure everything else was in working order, while I was working on the relay sockets I checked the function of the start inhibit relay. I confirmed +12v from the key, and ground to the Neutral Safety Switch. I also confirmed that the blue wire is getting +12v when the key is turned to "start."

Now that I have found that quick-splice connector, it makes sense: in the beginning, that little piece of tin managed to carry enough current to turn the starter motor, but with time and moisture it has probably lost its ability to carry enough current.

I should add that I cannot access the connections on the starter motor itself, since Houston's "Performance Exhaust" has been installed on my car.

I am going to try soldering the blue wire to the red/white wire and see if that solves the problem. In the meantime, is there anything else I should check?

Thanks!

Farrar
03-03-2013, 09:45 PM
Before I engaged in any jiggery-pokery (that's a technical term), I got a good look at the area. Here's what I found:

Not one quick-splice connector, but two -- one white/red wire quick-spliced to another white/red wire, quick-spliced to the blue wire, which runs to the relay. Both of these are just behind the bulkhead connector and very difficult to get to amongst their surroundings. Nonetheless, I tried to take a picture to illustrate.

16954

Look very carefully at that picture and you'll see a white/red wire which has been cut off. Here's a better view...

16955

...where you can see that there are TWO white/red wires which have been cut off.

The bulkhead diagram shows that the two white/red wires there go to the starter motor. There's a lot of current going to the starter motor, so I don't think replacing two 12-gauge wires with one was such a great idea on the part of whoever did this repair job years ago.

The proper way to repair this would be to remove the damaged portion of the white/red wires, solder in replacements, and then tape everything back up. But I can see where the previous owner had a problem: the wires were cut too close to the back of the bulkhead connector.

In order to effect a proper repair, I will need to remove everything I can from in the way, and pull the bulkhead connector back from the bulkhead. I am pretty sure that if I try to do that, I will break the bulkhead connector.

I am pretty sure that this white/red wire, taped off with blue electrical tape, is the original "to the bulkhead terminal" wire.

16956

It's too late tonight, but later in the week I will check continuity and see which of the two white/red wires cut by the bulkhead terminal this one is, and then label the wires. After that, I will see if I can put things back to stock configuration, even if I end up using the wrong color wire. (I dunno if I can find striped wire, though.)

Is there a gentle way to remove the bulkhead connectors?

Nicholas R
03-03-2013, 11:19 PM
Does your car have this update:
http://www.specialtauto.com/delorean-parts/images/starter-mod.jpg
You're really close to the vin cutoff but who knows. Just a thought.

Farrar
03-03-2013, 11:22 PM
Does your car have this update

Yes.

Nicholas R
03-03-2013, 11:34 PM
Yes.

Got ya, just curious. I had an intermittent non-starting issue once I did my swap and had a different starter. This turned out to be part of the problem.

Farrar
03-04-2013, 01:30 AM
Unfortunately, it's never anything that easy -- not with my car, anyway... Thanks, though!

Farrar
03-04-2013, 11:30 AM
Well, the good news is it looks like I can purchase another connector if needed from here (http://www.britishwiring.com/7-Way-3mm-Pin-Socket-Connector-p/c827.htm). The female part won't match the rest of the terminals, though.

Not having access to my car here at work (where I don't do anything until I've had my coffee... that's ethical, right?), I was able to find a large photo of the bulkhead terminals in the engine compartment. It looks like if I am careful enough, I should be able to push in the three tabs on the bulkhead connector enough to dislodge them from the metal plate there. I will probably have to do this for all of them, in order to get the slack I need to solder things back together. So this looks tedious, but not too bad. I guess I might as well freshen up all the rusty metal while I'm there -- the hot and ground bundles inside the car have some corrosion on them. With luck, I can get started this weekend, although I have work both days.

Ron
03-04-2013, 11:35 AM
I think you are on the right track soldering all spliced connections (It don't take much power for a solenoid to hold, but a lot to kick in...).

Farrar
03-04-2013, 11:47 AM
I think you are on the right track soldering all spliced connections (It don't take much power for a solenoid to hold, but a lot to kick in...).

Thanks, Ron.

Bitsyncmaster
03-04-2013, 12:16 PM
I think you are on the right track soldering all spliced connections (It don't take much power for a solenoid to hold, but a lot to kick in...).

Agree. I think the pull in current is 20 amps but the hold current is much less. That's why the solenoid has two coils.

Farrar
03-04-2013, 12:20 PM
the solenoid has two coils.

That explains the two white/red wires, even though I only see one on the wiring diagram. Thanks!

David T
03-04-2013, 12:29 PM
Inrush current on an inductor (coil) can be as high as 5 times the holding current. The starter solenoid has only 1 coil. The second connection is a switch to bypass 1/2 of the ballast resistor while the starter is cranking. As high as that may seem it is small compared to the inrush current of the starter motor. It can drop the voltage so much that the solenoid coil loses power and lets go. IMHO that was the reason for the mod, to keep the voltage up high enough so the solenoid coil for the starter won't drop out as the starter kicks in with a low battery.
David Teitelbaum

Farrar
03-04-2013, 12:32 PM
IMHO that was the reason for the mod,

You're referring to the factory relay socket modification, and not what the previous owner did to this circuit, right?

Ron
03-04-2013, 12:41 PM
Inrush current on an inductor (coil) can be as high as 5 times the holding current. The starter solenoid has only 1 coil. The second connection is a switch to bypass 1/2 of the ballast resistor while the starter is cranking. As high as that may seem it is small compared to the inrush current of the starter motor. It can drop the voltage so much that the solenoid coil loses power and lets go. IMHO that was the reason for the mod, to keep the voltage up high enough so the solenoid coil for the starter won't drop out as the starter kicks in with a low battery.
David Teitelbaum Actually, there are two windings, or coils, inside, but one end of each are common. (I posted a schematic of it here somewhere...IIRC one of the other ends goes directly to ground and the remaining grounds through the armature.)

Bitsyncmaster
03-04-2013, 12:49 PM
Actually, there are two windings, or coils, inside, but one end of each are common. (I posted a schematic of it here somewhere...IIRC one of the other ends goes directly to ground and the remaining grounds through the armature.)

I works higher current until the armature gets power, then both sides of that coil have 12 volts which turns it off. The armature only get power when the solenoid has pulled in fully.

DMC5180
03-04-2013, 04:48 PM
Farrar,

If you are going make an order from British wiring, why not order 3 ft of the proper color coded wire and replace the wire completely from the relay socket to the BH connector. Btw, you don't need to to replace the connector shell. Just de pin the the terminal from the BH connector get a new terminal (BW has them) and crimp to the New wire and insert into the connector housing. Then run the new wire along the original harness path to the relay socket. Cut wire to length and crimp on a new relay socket spade receptacle (also available from BW). Clip it in and your done. GOOD AS NEW. No solder splicing. Btw It never hurts to some of those Crimp terminals on hand. I'd get a dozen of both sides if your making an order.

BW sells the wire in the correct colors (WHITE/red) (PRIMARY/trace) 28 strand (12 AWG) $1.00 per meter or 44 strand (14 AWG) $1.25 per meter.

3 MM male pins (C833) $0.45 ea BH connector side.

1/4 female spade for housing (C226) 28 strand wire $0.30 ea

1/4 female spade for housing (C228) 44 strand wire $0.30 ea

Farrar
03-04-2013, 04:50 PM
That's excellent, Dennis! I would really prefer to have the proper wire color -- colour? ;) -- so I'll have to make that order up! Thanks!

SS Spoiler
03-04-2013, 05:43 PM
Dennis is giving the Daves a run for the money, when it comes to "techy" stuff. Good work!

DMC5180
03-04-2013, 06:07 PM
That's excellent, Dennis! I would really prefer to have the proper wire color -- colour? ;) -- so I'll have to make that order up! Thanks!

:thumbup:

Btw: it's supposed to be ( C228 ) not a smiley face. the computer read the characters as an emoticon. I listed both wire sizes to give you the options to pick one. I'm not sure what the OE wire size is but you can count the strands to figure it out. In this case 44 strand (12 AWG) would be the better option.

If you don't find everything within the BW [Components] menu options let me know.

3 MM male pins are the [multi-wire connectors] section

1/4" Spade terminals for housings are in [spade terminals] section

PVC covered wire is in the [wire] section.

DMC5180
03-04-2013, 06:27 PM
Dennis is giving the Daves a run for the money, when it comes to "techy" stuff. Good work!

Thanks Paul, The knowledge base of the DAVE's is far superior than mine.

I just try to give appropriate answers or common sense solutions to the questions at hand based on my own knowledge and experiences.

Bitsyncmaster
03-04-2013, 08:35 PM
Eliminating the splice is the best way to go. I wish I could stock all the striped wire but it's just not practical for an individual.

Farrar
03-04-2013, 09:40 PM
Although I appreciate Dennis' help in finding the parts at British Wiring, I would end up paying $7.70 shipping for $1.65 of merchandise! Looks like I will go with non-striped wire, and simply make a note for future reference.

Thanks!

Ron
03-05-2013, 12:55 PM
$.03

I must have posted that diagram on .com, so I fixed/expanded on a pic I found on a Vett forum I visit...

1. Switch OFF
17000


2. Switch In Crank Position (Initial)
16998
Note current flowing through both Coils. The Solenoid begins to pull the Gear Drive into the Flywheel and bring the Copper Disk toward the two main Contacts for the Starter.
It takes 30-50 Amps to operate a solenoid at this stage (...why you DO NOT want to use crimp connections...and why you should always use a large wire, as Dennis mentioned.)


3. Switch In Crank Position (Held)
16999
Note the Pull In Coil has 12v at both ends of its winding at this stage (as Dave mentioned), so current stops flowing through it. But the Hold Coil (Red) will maintain the engagement by itself. In this stage, the Armature (or Rotor) is supplied with power. If the battery is low or there is a bad connection, the Starter can pull enough power to starve the solenoid making the solenoid "drop out". This in turn disconnects the Aramture, so the available power goes back up and the solenoid re-engages. This cycle continues until the operator releases the key and begins to generate four letter words.

DMC5180
03-05-2013, 01:41 PM
Although I appreciate Dennis' help in finding the parts at British Wiring, I would end up paying $7.70 shipping for $1.65 of merchandise! Looks like I will go with non-striped wire, and simply make a note for future reference.

Thanks!

I know psychologically it's against human nature to spend more in shipping than merchandise. This is why I mentioned getting multiple qty's of the 3MM Pins and sockets along with any other Unique items that would be good to have on hand. Make the purchase worth while. You have too look at things differently and say too yourself. I can fix the PO's hodge podge repair for less than 10 bucks and have it factory correct with little effort. Satisfaction Guaranteed.

Farrar
03-05-2013, 10:34 PM
I know psychologically it's against human nature to spend more in shipping than merchandise. This is why I mentioned getting multiple qty's of the 3MM Pins and sockets along with any other Unique items that would be good to have on hand. Make the purchase worth while.

Well, I took your advice. I remembered that some of the "Posi-Lock" connectors on my car are damaged or missing (e.g. connectors at a/c diodes, one of the door switch connectors) and ordered some of those. Then I decided to get some spare relay terminals (the 1/4" ones with the locking tab) because I ran out a while ago. And I filled my cart with extra 3mm pins until it reached $19.95 -- a nickel below the threshold between $6 shipping and $10 shipping. And now, my order is on its way. :)

Thanks!

DMC5180
03-05-2013, 11:33 PM
Well, I took your advice. I remembered that some of the "Posi-Lock" connectors on my car are damaged or missing (e.g. connectors at a/c diodes, one of the door switch connectors) and ordered some of those. Then I decided to get some spare relay terminals (the 1/4" ones with the locking tab) because I ran out a while ago. And I filled my cart with extra 3mm pins until it reached $19.95 -- a nickel below the threshold between $6 shipping and $10 shipping. And now, my order is on its way. :)

Thanks!

Cool Beans :thumbup:

Farrar
04-29-2013, 01:52 PM
Well, I fixed it.

Here's how.

I started at the bulkhead terminal and crimped a new 3mm pin onto the ends of the white/red wire I bought from British Wiring.

1862018626

I know the factory didn't use heat-shrink, but I used it just because it makes me feel better. Also, the factory wire looked like 14AWG. I used 12AWG wire instead. And I sanded the other pins shiny before re-installing the connector.

Then I stuck the wire into the harness and threaded it through. When I reached the hot-start relay socket, I cut the wire to length, and made that connection.

1862118622

With the other length of wire, I continued along to the start inhibit relay socket. I snipped off the leftover wire (I had ordered three meters), and made the third and final connection.

1862318624

Then I replaced the relay and put the battery on the charger for several hours.

Several weeks elapsed before I was able to get back into the garage and test this repair. I finally got around to it yesterday afternoon.

First I verified continuity with my multimeter. Then I plugged everything back in.

The multimeter read 12.22 volts on the battery, which should have been enough to turn the starter motor. I installed and connected the battery, then hopped in and turned the key to "Start."

I heard relays clicking, but the starter motor did not turn. I went back to the engine compartment to double-check everything and I noticed that at some point in the recent past I had jumped the Otter Switch connections. Since the radiator fans did not turn with the Otter Switch jumped, I figured they might be seized and drawing too much current to allow the starter motor to turn from a 12.22v battery.

The gauge on the dashboard was actually reading just under 12v at this time. I returned the Otter Switch connections to the switch, and decided to try again. It worked! I tried three times to make sure it wasn't a fluke. The starter motor turned each time. I couldn't fire up the engine because my fuel pump is dead, but this is still great progress.

My thanks to everyone who helped me with advice and encouragement in getting this repaired.

Farrar

David T
04-29-2013, 04:34 PM
So you are saying the wiring repair did not "fix" the problem but it went away by removing the jumper you had in place of the otterswitch? That is weird because if that circuit was drawing that kind of power something should have either popped or smoked. I would not claim victory yet. There is more to find.
David Teitelbaum

Farrar
04-29-2013, 04:36 PM
So you are saying the wiring repair did not "fix" the problem but it went away by removing the jumper you had in place of the otterswitch?

No. I am saying that I think the additional drain on the battery caused by seized radiator fans prevented the starter motor from turning when I turned the key for the first time yesterday. The wiring repair fixed the problem of not being able to start the engine from the key.