Log in

View Full Version : Frame & Body 110720/1 door sill seal proper shape?



Jonathan
03-03-2013, 09:03 PM
Does anyone have a close up view of this:

16953

The resolution isn't high so zooming in doesn't work very well.

I have the superseded ones, 110720 and intend to get them installed (on both doors). They don't have any pre-drilled holes for the screws, nor cut-outs for the door light receptacle.

I plan on using my existing metal strips as templates, but would also like to see a finished product before I start in order to make sure I end up with what was intended. Ya know, measure twice, cut once kinda thing...

jackb
03-04-2013, 12:03 AM
I just replaced that seal on both doors a few weeks ago. The webpage's index numbers that point to the item in the picture do not match the index/part number on the list below the picture, so I when I ordered them I said its x on the picture, but I believe it is x in the list, and said "the seal at the bottom of the door". I would recommend ordering it the same way (describing it over the phone) to ensure you recieve the correct seal.

Like you said, it has no cutouts or holes but that is unnecessary.
I removed the screws holding the metal strip/seal to the door, and removed it.
Then I drilled out the rivets holding the seal to the metal strip.
They also have some glue, so I finished peeling and scraping the seal off.
I lined up the new seal on the metal and used a punch to make a guide hole for the pop rivets.
I pop-riveted the new seal onto the metal strip.
Then screw the metal strip with the new seal back on the door.
Then make the cutout for the door light and trim the edge of the seal where it passes the end of the door.

Jonathan
03-05-2013, 01:09 PM
Good plan of attack, Jack.

Is riveting necessary? I think the pieces of what was left of my seals were only held in there with the screws. Basically wedged between the metal strip and the door with the screws plus some adhesive like you said, cause I've also had to scrape away at it to get the last of it off.

DMCMW Dave
03-05-2013, 02:05 PM
Hear are pictures of the two style lower seals. They are the same rubber, but the metal is a different shape.

Note that on the early one the rubber is to the outside, on the later one it actually passes over the door edge light.


Early Style detail
17001

Early Style profile
17003

Late Style detail
17002

Late Style profile
17004

mac
04-13-2016, 07:24 PM
Hi, where do I get that metal strip? Cannot find a part no. for that. My car is missing the complete seal with metal strip on the driver's side, but it is there on the passenger's, so I wanted to add it (just realized after 7 years of ownership^^).

mluder
04-13-2016, 08:28 PM
Hi, where do I get that metal strip? Cannot find a part no. for that. My car is missing the complete seal with metal strip on the driver's side, but it is there on the passenger's, so I wanted to add it (just realized after 7 years of ownership^^).
You hope to find a decent used one. Last I checked they were no longer available officially but DMC California managed to find one for me.

Cheers
Steve

DMCMW Dave
04-13-2016, 11:05 PM
Hi, where do I get that metal strip? Cannot find a part no. for that. My car is missing the complete seal with metal strip on the driver's side, but it is there on the passenger's, so I wanted to add it (just realized after 7 years of ownership^^).

Parts car.

BABIS
04-14-2016, 02:51 AM
Hear are pictures of the two style lower seals. They are the same rubber, but the metal is a different shape.

Note that on the early one the rubber is to the outside, on the later one it actually passes over the door edge light.


Early Style detail
17001

Early Style profile
17003

Late Style detail
17002

Late Style profile
17004

Great explanation Dave, I thought it was possible to mount the seal in both ways but now I see it really depends on the metal strips the car has...

Jonathan
04-14-2016, 08:58 AM
I made this how-to not long after the original comments in this thread. It isn't mentioned in the write-up, but I did go back and make an additional cut-out for the small drain holes that need to be there as I missed that part initially.

41476

JAZ_DMC
06-11-2019, 02:09 PM
I made this how-to not long after the original comments in this thread. It isn't mentioned in the write-up, but I did go back and make an additional cut-out for the small drain holes that need to be there as I missed that part initially.

41476

Thank you for this. Excellent resource!