Log in

View Full Version : Transmission Auto $%%! Auto Trans Dipstick!!



DMC_PRIME
03-04-2013, 05:58 PM
:banghead:

The freaking end tip came off inside the transmission. The leftover piece (inch or two) must be still in the up/down position because the dipstick went just about all the way in.....

Options guys???

Is there any other options then dropping the pan? And if I did that, will it be right there?

What a way to end a great cruise.......... :mecry:

DMCMW Dave
03-04-2013, 07:42 PM
:banghead:

The freaking end tip came off inside the transmission. The leftover piece (inch or two) must be still in the up/down position because the dipstick went just about all the way in.....

Options guys???

Is there any other options then dropping the pan? And if I did that, will it be right there?

What a way to end a great cruise.......... :mecry:

You can remove the dipstick tube at the transmission. Drain the fluid first or you'll have a mess. The only tricky part about this is getting the o-ring back in place without leaks. Order a new O-ring or two when you order the dipstick.

DMC_PRIME
03-04-2013, 08:20 PM
You can remove the dipstick tube at the transmission. Drain the fluid first or you'll have a mess. The only tricky part about this is getting the o-ring back in place without leaks. Order a new O-ring or two when you order the dipstick.

How is the dipstick tube connected? I am not at my car right now. Actually, as soon as this all happened I had to run to work.. Are you saying this is easier and cheaper than dropping the pan?

Thanks for getting back to me.

Mark

lazabby
03-04-2013, 08:24 PM
How is the dipstick tube connected? I am not at my car right now. Actually, as soon as this all happened I had to run to work.. Are you saying this is easier and cheaper than dropping the pan?

Thanks for getting back to me.

Mark

The tube merely fits into a hole and it's help in place at the top of the tube by the bracket.. Normally it has o-rings to prevent leakage. I recommend getting the gasket that holds the otterstat valve. It's much nicer and fits perfectly.

Jonathan
03-04-2013, 08:54 PM
The tube merely fits into a hole and it's help in place at the top of the tube by the bracket.. Normally it has o-rings to prevent leakage. I recommend getting the gasket that holds the otterstat valve. It's much nicer and fits perfectly.

Mine leaked recently and needs a new seal. The otterstat seal was suggested, but one concern was raised over compatibility of materials. The material the otterstat seal is made of is able to handle coolant, but not sure it handles ATF as well. Anyone have any history on the long term performance of this otterstat seal in there instead of a couple o-rings?

DMC_PRIME
03-04-2013, 09:01 PM
The tube merely fits into a hole and it's help in place at the top of the tube by the bracket.. Normally it has o-rings to prevent leakage. I recommend getting the gasket that holds the otterstat valve. It's much nicer and fits perfectly.

Wow, sounds like I may not have to drain the pan and open everything up. I can't wait to look at it some more. So this is the route everyone would go? But when I pull the tube out, what are the chances that the broken piece falls out into the transmission? Add my bad luck to that percentage when calculating.

Jonathan
03-04-2013, 09:35 PM
There is nothing but empty space between the end of the dipstick tube and the pan, as far as I know. None of the gear teeth are near there anyway. The filter is in there somewhere though. Not sure where exactly as I've not taken one apart. If the piece goes anywhere it will be to go lie on the bottom of the pan.

DMC_PRIME
03-04-2013, 10:53 PM
There is nothing but empty space between the end of the dipstick tube and the pan, as far as I know. None of the gear teeth are near there anyway. The filter is in there somewhere though. Not sure where exactly as I've not taken one apart. If the piece goes anywhere it will be to go lie on the bottom of the pan.

Ok, that is what I was thinking also. Dave suggested that I drain the fluid before taking the tube out, is that necessary? I just had that whole pan apart and the fluid is clean as can be.

Jonathan
03-04-2013, 11:28 PM
Ok, that is what I was thinking also. Dave suggested that I drain the fluid before taking the tube out, is that necessary? I just had that whole pan apart and the fluid is clean as can be.

Drain it, yes. Throw it away, no (unless you really want to).

The suggestion to drain the fluid prior to removing the dipstick tube is because the normal resting fluid level is above the sealing point of the bottom of the dipstick tube. If you remove the dipstick tube, you will be draining some of your fluid. It just depends whether you want it to drain into a bucket or onto the floor.

Dangermouse
03-05-2013, 01:32 AM
If you have just had the pan off, I would drain the fluid and try removing the dipstick tube first. If the tip is in there, then remove and refit the tube with the new seal. If not, then you will need to drop the pan.

I don't think the broken tip can cause any damage as the filter will stop it getting into the pump. Hopefully it will get stuck on the little magnet.

If you hadn't just removed the pan, I would suggest jumping right to that as it wouldn't do any harm having the pan internals and filter inspected.

Ryan King
03-05-2013, 01:44 AM
Dont use those stupid O-Rings.

I had a massive leak where my dipstick tube connects to the transmission. I had those stupid O-Rings and they never did anything. I had 2. Tried 3. Tried 4. Damn thing still leaked. I had read someone using an outterstat seal, and I tell ya, it has never leaked since. It fits perfectly and seals perfectly. I have had mine in there for over 2 years now. Not a single problem.

Dont waste your time with the O-Rings.

OverlandMan
03-05-2013, 09:50 AM
Dont use those stupid O-Rings.

I had a massive leak where my dipstick tube connects to the transmission. I had those stupid O-Rings and they never did anything. I had 2. Tried 3. Tried 4. Damn thing still leaked. I had read someone using an outterstat seal, and I tell ya, it has never leaked since. It fits perfectly and seals perfectly. I have had mine in there for over 2 years now. Not a single problem.

Dont waste your time with the O-Rings.

I have a small ATF leak and was planning on changing the pan gasket and the dipstick tube seal all in one Saturday morning. Is this the otterstat seal you guys are talking about? http://store.delorean.com/p-6350-seal-cooling-fan-switch.aspx

David T
03-05-2013, 11:47 AM
Don't mess with the dipstick tube. Drain the oil and pull the pan. You will find the tip easily. You may also want to clean the filter while you have the chance. Clean the pan and magnet and replace the pan gasket. Refill with fluid as per the procedure in the Workshop Manual G:04:02. Check the final drive and it can't hurt to go over all of the external, on car adjustments.
David Teitelbaum

Ryan King
03-05-2013, 03:29 PM
I have a small ATF leak and was planning on changing the pan gasket and the dipstick tube seal all in one Saturday morning. Is this the otterstat seal you guys are talking about? http://store.delorean.com/p-6350-seal-cooling-fan-switch.aspx

Yes, that is the one. You wont regret it



Don't mess with the dipstick tube.


I completely disagree. It is bound to leak at some point. Those O-Rings will get old and they will leak. Its one of those "While im in there I might as well..." type things. If he is going to drain the pan and replace the gaskets, this might as well get done too.

OverlandMan
03-05-2013, 03:41 PM
Yes, that is the one. You wont regret it


Cool - thanks for the info. I'll pick one of these up on my next order.

DMC_PRIME
03-05-2013, 08:43 PM
Dont use those stupid O-Rings.

I had a massive leak where my dipstick tube connects to the transmission. I had those stupid O-Rings and they never did anything. I had 2. Tried 3. Tried 4. Damn thing still leaked. I had read someone using an outterstat seal, and I tell ya, it has never leaked since. It fits perfectly and seals perfectly. I have had mine in there for over 2 years now. Not a single problem.

Dont waste your time with the O-Rings.

Thanks, I will pick one up when I order.

DMC_PRIME
04-04-2013, 03:59 PM
I finally got around to this project. I did mess with the dipstick tube and hope to get lucky, but no luck. The pan had to come off. It was there laughing at me.......

Quick question, how much fluid should I need to get it back to normal level. 3 or 4 quarts????

Ron
04-04-2013, 04:30 PM
~5Qt?

17898

DMC_PRIME
04-04-2013, 06:12 PM
~5Qt?

17898

Thanks for replying, I guess I will need to get more than I thought.

I didn't realize it would that much. I saw that chart say 1.57gallons. Which is around 6 quarts. I thought I heard somewhere not all the fluid drains out... Correct or not?

Nicholas R
04-04-2013, 08:46 PM
Honestly id say to just measure how much you get out and put that much back in. You'll never fully drain the torque converter so the actual amount you'll need can really vary. I think when I did mine years ago I got about 4qt out, but I'm not positive.

DMCMW Dave
04-04-2013, 08:50 PM
Depends on how long you let it drain but it seems to be about 4 on a simple drain/refill. You can't empty the converter so you don't really get all 6 qts out.

David T
04-04-2013, 10:37 PM
The only proper way to refill is to follow the procedure in the Workshop Manual. G:04:02. You cannot just measure what comes out and put the same amount back in. Maybe there was too much or not enough before you drained it. Don't forget to check the final drive too. I would also recommend checking ALL of the in-car external adjustments as long as you are working on the transmission. If you are doing this to flush the transmission, you cannot drain it completely. The only way to properly flush all of the old stuff out is to go to a transmission shop and have them power flush it (or disassemble it). If the fluid is very dark and smells burnt and feels gritty between your fingers this can extend the life of the seals and bearings. If there is a LOT of friction debris in the pan it is an indication you are nearing the end of the life of the transmission. If there is any significant amount of metal, that is also bad. The filter cannot be inspected unless you cut it open.
David Teitelbaum

DMC_PRIME
04-04-2013, 11:23 PM
Thanks for all the replies. I will just buy 5 quarts and go from there and add until it is at the proper level.... As for the shape of the transmission, it is amazing condition. A transmission shop used those exact words to me not that long ago. :bigclap:

jangell
05-31-2015, 05:49 PM
Dont use those stupid O-Rings.

I had a massive leak where my dipstick tube connects to the transmission. I had those stupid O-Rings and they never did anything. I had 2. Tried 3. Tried 4. Damn thing still leaked. I had read someone using an outterstat seal, and I tell ya, it has never leaked since. It fits perfectly and seals perfectly. I have had mine in there for over 2 years now. Not a single problem.

Dont waste your time with the O-Rings.

Resurrecting an old thread...

My dipstick tube snapped right at the transmission. Luckily I was able to get the broken part out without too much trouble other than a broken pry bar.

I found this thread and got the otterstat seal (106959), but while it fit fine over the tube it seemed too large to fit in the hole in the transmission. I used an O-ring instead, but that feels too loose (although I've only tightened the lower bracket bolt into the transmission; I haven't done the one on the engine yet, which should stabilize it a bit).

I'm wondering if there's a trick to fitting the otterstat seal into the transmission. It's easy enough to take back out (my car is still raised as I do more work under it), and I didn't put any RTV on it when I installed it with the O-ring. I figure that if I can't get the otterstat seal to work I will just use RTV/Permatex.

Thanks!

-- Joe

DMC5180
05-31-2015, 08:19 PM
Although the I have never done it. I would think lubrication on the inside and outside of the seal would allow things to fit in place. Put the seal in first then push the tube through it. If others have done it, it shouldn't be to big a deal for you. Btw if you were replacing the otters tat you would have to insert the seal before putting the otterstat in.

jangell
05-31-2015, 08:20 PM
Ah. Yes, putting the seal in first would make more sense. I'll give that a try next weekend. Thanks!

-- Joe

DMC_PRIME
05-31-2015, 10:16 PM
One of my old threads.... I still remember how pissed i was that day.