Log in

View Full Version : Engine Ahh, plastic and hot water



Spittybug
03-15-2013, 08:56 PM
Word of advice for anyone with plastic Tees in their heater hose lines: replace them!

I have a bleeder line from the water pump over to the overflow bottle where it tees with the hose running to the heater core. I've had a white plastic (not nylon, seems more like a talc or glass reinforced PVC perhaps?) in that line for several years with no problems, until now. These claimed to be usable for heater hoses, not simply for vacuum.

I went to my beer brewing supply house today with my son and we took the D for a drive on such a beautiful day. Everyone and his G&*@!D brother, sister and aunt was driving on the roads today and we sat in some nasty jams. I noticed the temp creeping up and reminded myself to re-bleed the top radiator hose once I got home. The fans would kick on and bring the temperature back down again. Still, the swing had me anxious. We got stuck behind a multicar pile up on the beltway with no off ramp nearby. Sure enough, the temp would climb, come down, climb come down... then, just as the traffic started to move, clouds of white steam all over.... damn... I'm in the fast lane right by the toll plaza, about 8 lanes wide! I shut it down quick and played the start, accelerate, shut down, coast game for a couple of minutes as the traffic dissipated and I could get to the next exit. Immediately pulled into a U haul store. Yup, the plastic Y connector had failed on 2 of the legs and was dumping antifreeze all over.

I connected the water pump line straight to the nipple on the overflow bottle and took the heater line and wedged it in the open mouth of the overflow once the cap was off. I used the remainder of the Tee and the hose clamps to make sure it didn't pop out. I filled up with water, tested my open system and drove the remaining 5 miles or so home keeping my eye on the temp gauge. It never broke 160. Stopped at O'Reilly and bought a brass Tee and a jug of antifreeze. Got home, hosed the entire engine down to remove the residue and installed the Tee. Point worth noting; Hervey's spark plug wires and boots were soaking wet and the water pooled on the engine was deep around the plug boots. No problem starting or running as the water was kept out.

As luck would have it, a nice day, no pressing time constraints, close to home, relatively simple problem and fix....all ended up being a good learning experience for my son who isn't particularly technical. It let him see how understanding how things work can really help and that it pays to have a couple of tools with you.

jawn101
03-16-2013, 01:25 AM
Wow Owen, quick thinking on that one. My one and only tow in the D was when the heater control valve (also plastic) failed and did the same thing to me. I wasn't confident enough in the hose routing to connect anything to anything else and limp it home - plus it was pitch dark. That whole heater control assembly is a pain!

Glad you made it home OK. :)

WelmoedJ
03-16-2013, 05:36 AM
Having a D is not only Living the Dream, in some cases likes yours it's surviving the Nightmare :)

Citizen
03-16-2013, 09:33 AM
Got home, hosed the entire engine down to remove the residue and installed the Tee. Point worth noting; Hervey's spark plug wires and boots were soaking wet and the water pooled on the engine was deep around the plug boots.

Although not a big item of concern for you right at the moment, I wonder if water got into the VOD.

Using a flashlight, you might do some probing into the VOD with a cotton ball glued to a long stick. If you can see water/coolant or the cotton comes back wet, you could try a wet/dry vac with a modified nozzle to get small amounts of moister out. If it got flooded, you might have a big job in your future (sorry).

...

Bitsyncmaster
03-16-2013, 10:47 AM
I may have a plastic T on mine. Lots of cars use plastic in the coolant system. Maybe it's just the T's get to much side force and breaks. I've seen white and black plastic and wonder if one is better.

Citizen
03-16-2013, 10:50 AM
I have a black T, and no problems for at least 5 years. But I guess I'm going to go check it out a bit closer.

...

Spittybug
03-16-2013, 10:57 AM
I recently rerouted all of my hoses to the driver's side of the engine bay. It is plausible that the Tee was now having some forces on it that it didn't before. Sitting where it was for so long, getting hot, cooling, getting hot, cooling.... it probably softens and re-hardens, each time getting a bit less elastic and more brittle. When I reconnected everything to the other side of the engine, undoubtedly the hoses were pulling on the Tee differently than they were before. Go through just a couple warm up cool down cycles and voila, the slight brittleness is enough to cause it to fail? Sounds like a good theory to me.

Yes, my valley got soaked in the hose down. Mine is quite easy to access with my Peugeot manifold. I will check to see how much is left and either suck it out or just let it evaporate. We're having such nice weather I'll be driving the car......

eagle-co94
03-16-2013, 11:39 AM
There's a black plastic T in my Impala SS' cooling system that is known to be the weak point in the entire system. There's not a lot you can do about it unless you replace it with a brass T and lines as well because the geniuses at GM have 2 different diameter hoses at that T.

TTait
03-16-2013, 04:03 PM
Yes, my valley got soaked in the hose down. Mine is quite easy to access with my Peugeot manifold. I will check to see how much is left and either suck it out or just let it evaporate. We're having such nice weather I'll be driving the car......

Suck out what you can with a shop vac, and then rinse well with clean water, then repeat. One good drive later and it should be clean and dry with no coolant residue.

Spittybug
03-16-2013, 09:53 PM
Yup.... shop vacs are great. Popped the spark plug wires off the plugs and found water in the wells (should I revise that previous post???). That explains the somewhat rough running I'm sure. Shop vac'd it out. Here's a trick; use one of those long thin (really long nose piece) funnels from the automotive stores, upside down, and then use the shop vac funnel attachment inside it. You can get in some tight nooks and crannies.

jawn101
03-16-2013, 09:55 PM
Yup.... shop vacs are great. Popped the spark plug wires off the plugs and found water in the wells (should I revise that previous post???). That explains the somewhat rough running I'm sure. Shop vac'd it out. Here's a trick; use one of those long thin (really long nose piece) funnels from the automotive stores, upside down, and then use the shop vac funnel attachment inside it. You can get in some tight nooks and crannies.

Since I didn't have a shop vac until very recently, I always just jammed a wad of paper towels down in the well with a long flat screwdriver, then extracted them with forceps.