View Full Version : Electrical capacitor behind bulkhead terminals
Farrar
03-17-2013, 12:11 PM
All,
Apologies is this has been covered before; I did a search for "bulkhead + capacitor" and turned up nothing.
I am doing some repairs to the wiring harness inside the car, and have noticed a capacitor quick-spliced into the harness from one bulkhead terminal to another. The capacitor is connected between a solid green wire (red wire of cap) and a black ground wire (black end of cap). The connections are marked with red electrical tape.
This looks official as the capacitor used is the same type used elsewhere on the car. However, it crowds things back there where I am working, and I assume it was merely introduced to reduce AM radio interference. Would it be safe to remove the capacitor and seal up its quick-splice locations? Or should I leave it alone?
Thanks,
Farrar & #2613
Bitsyncmaster
03-17-2013, 03:05 PM
Do you know what it connects to? Use the bulkhead wire list to find out.
Sounds like it is across the GC power supply (since only one connector, Red, has both colors).
It would make more sense if the Green wire had a brown stripe (reverse light switch noise).
Farrar
03-17-2013, 07:06 PM
According to Dave's list, its purpose is assumed to be power to Pin 1 of Idle ECU, but there's a question mark next to it.
Here's a picture which will, I hope, help clarify things a bit.
17408
Thanks,
Farrar
DMC5180
03-17-2013, 07:36 PM
Sounds like it is across the GC power supply (since only one connector, Red, has both colors).
It would make more sense if the Green wire had a brown stripe (reverse light switch noise).
Since when does a reverse light switch cause noise? That's a new one on me.
Bitsyncmaster
03-17-2013, 07:38 PM
H 45 G Power to pin 1 of Idle ECU?
I would just cut that cap off. It looks like a PO modifcation to me with that clamp type wire splice.
DMC5180
03-17-2013, 07:39 PM
According to Dave's list, its purpose is assumed to be power to Pin 1 of Idle ECU, but there's a question mark next to it.
Here's a picture which will, I hope, help clarify things a bit.
17408
Thanks,
Farrar
I take it you are in the process of Correcting the Start circuit wiring? How's it going?
According to Dave's list, its purpose is assumed to be power to Pin 1 of Idle ECU, but there's a question mark next to it.
Here's a picture which will, I hope, help clarify things a bit.
17408
Thanks,
FarrarOk, I wondered if you meant one terminal to another in the same Bulkhead Connector or between two connectors...Anyway, yes in the pic it is across the Idle ECU power supply -- Pitch it.
Since when does a reverse light switch cause noise? That's a new one on me.
It's common to hear complaints of "popping" or "clicking" in the speakers due to no/bad caps across reverse light, door light, brake light switches, and particular to a D, throttle enrichment micro, idle speed micro, AC mode switches. Introducing noise is just a characteristic for most any mechanical switch, especially when controlling a gang of lights @ 12V. Not to mention the havoc they raise with solid state and other electronics...
Farrar
03-17-2013, 11:26 PM
I take it you are in the process of Correcting the Start circuit wiring? How's it going?
So far, so good...
http://dmctalk.org/showthread.php?241-What-have-you-done-to-your-DeLorean-today&p=95051&viewfull=1#post95051
Ok, I wondered if you meant one terminal to another in the same Bulkhead Connector or between two connectors...Anyway, yes it is across the Idle ECU power supply -- Pitch it.
Cool, I was hoping I could get rid of it. Thanks!
DMC5180
03-17-2013, 11:28 PM
Ok, I wondered if you meant one terminal to another in the same Bulkhead Connector or between two connectors...Anyway, yes it is across the Idle ECU power supply -- Pitch it.
It's common to hear complaints of "popping" or "clicking" in the speakers due to no/bad caps across reverse light, door light, brake light switches, and particular to a D, throttle enrichment micro, idle speed micro, AC mode switches. Introducing noise is just a characteristic for most any mechanical switch, especially when controlling a gang of lights @ 12V. Not to mention the havoc they raise with solid state and other electronics...
Is the noise mostly heard when using AM stations? For the most part I can't get any AM stations to come in accept a very local station in town. All I get for the most part is ignition ticking. It's still the Craig radio.
Yes, AM, and older radios in general are more prone.
If you hear clicking from the ignition, it is probably a plug wire (with whining, suspect the capacitor at the coil more).
DMC5180
03-17-2013, 11:51 PM
I Do have a very high pitch frequency whining (not buzz) that I've never been able to locate. I mostly here it right after I start the car and seems to come from the rear passenger side corner. I can't tell if it's speaker noise or something else. It's almost like white noise. It seems to emanate from the back wall (perception anyway). Could that be the Capacitor under the coil cover doing that? It seems to fade away when when I turn the radio ON. Or am I just masking it?
jawn101
03-18-2013, 12:08 AM
I Do have a very high pitch frequency whining (not buzz) that I've never been able to locate. I mostly here it right after I start the car and seems to come from the rear passenger side corner. I can't tell if it's speaker noise or something else. It's almost like white noise. It seems to emanate from the back wall (perception anyway). Could that be the Capacitor under the coil cover doing that? It seems to fade away when when I turn the radio ON. Or am I just masking it?
I had a very similar thing, Dennis - but it went away the last time I removed my mixture unit and re-sealed the idle air pipe. I didn't positively identify any vacuum leak there, but I spent many hours tearing into and listening carefully at everything in the relay compartment and never found it....
It could be that (Its 'switch' is not mechanical but the power to it is constantly being made and broke...).
Try, tuning the radio around in the no/off station areas (AM), unplugging the speaker(s), measure the capacitor.
The alternator is also a common source for a high pitched whine (unplug it, or drop the belt if it has a self-energizing voltage regulator...(the cap is usually inside...)
Farrar
03-18-2013, 12:54 AM
What's a good source for the bulkhead terminals? A couple of mine need replacing. Looks like the car overheated at some point. The connectors are melted. This is the worst of the bunch, but two more are misshapen and will have to be cut from the bulkhead.
17419
Bitsyncmaster
03-18-2013, 06:03 AM
What's a good source for the bulkhead terminals? A couple of mine need replacing. Looks like the car overheated at some point. The connectors are melted. This is the worst of the bunch, but two more are misshapen and will have to be cut from the bulkhead.
17419
Those round pins, I could not find elsewhere. I bought 100 each from that same site you got them.
You can clean up those pins by putting the whole connector into a jar of TarnX. Then rinse the whole connector many times in a jar of clean water. I followed up the water cleaning with a jar of solvent. I should pull the bulkhead sides out so I can clean mine. I only did the harness side so far.
Farrar
03-18-2013, 10:46 AM
Thanks, Dave. What about the plastic parts?
Bitsyncmaster
03-18-2013, 07:27 PM
Thanks, Dave. What about the plastic parts?I think you can get them at the same place you bought the terminals. Actcualy by the connectors with the pins and it cost the same as the pins alone.
Farrar
03-18-2013, 07:55 PM
I sent an e-mail to British Wiring, asking if they had panel-mount housings. Within an hour (THAT's customer service!), I got a reply saying that, unfortunately, they don't. All they have are the in-line connectors, which have neither the lip nor the tabs to squeeze into the mounting plate.
I know this thread has now changed its topic to something else, so forgive me for going off-topic, but now it looks like I have a real problem: unavailability of bulkhead terminals. I can't find them anywhere! The 3mm pins are only 45¢ each, so I thought I could just shotgun the area, but now it looks like that's off the table. As far as I can see, I have the following options:
1. put the damaged connector back and hope it holds
2. use an inline connector and put a thick grommet in the mounting plate where the bulkhead connector used to be
3. fabricate a new mounting plate and use all new, but non-stock connectors.
Option 3 would be gruelling and non-reversible, but then again so would Option 2.
Suggestions?
Thanks,
Farrar
Bitsyncmaster
03-18-2013, 08:03 PM
I can see where those connectors are going to be hard to find. Your option 2 is what I would try if you cant find the mounted type.
Farrar
04-25-2013, 08:34 PM
In the end, I decided to simply re-use the connectors I have.
When I went back into the engine compartment to check the position of everything, I was surprised to find that there were also two white/red wires "outside" the bulkhead connector, coming from the same terminal "inside" where there were two wires. However, one of the wires has been cut off and judging from how brown the copper is it was cut off a long time ago.
This dovetails into my "no start" problem in that I now have to worry about where the other white/red wire goes. Or went. Or should go.
If it runs directly to the starter motor, then I'll have to remove one of the headers to check the connections on the starter motor itself. I have a heat gun which puts out 1000°F. I wonder if that is hot enough to loosen exhaust studs. FML.
In the end, I decided to simply re-use the connectors I have.
When I went back into the engine compartment to check the position of everything, I was surprised to find that there were also two white/red wires "outside" the bulkhead connector, coming from the same terminal "inside" where there were two wires. However, one of the wires has been cut off and judging from how brown the copper is it was cut off a long time ago.
This dovetails into my "no start" problem in that I now have to worry about where the other white/red wire goes. Or went. Or should go.
If it runs directly to the starter motor, then I'll have to remove one of the headers to check the connections on the starter motor itself. I have a heat gun which puts out 1000°F. I wonder if that is hot enough to loosen exhaust studs. FML.
The R/W wire goes to the Starter Solenoid, Cold Start Valve, Hot Start Relay, and Start Inhibit Relay.
No need for the heat gun ;)...while the engine is being cranked (pull the coil wire so it will not start), you should get 12(+) on the wire(s). One of the two at the White Bulkhead Connector is for the Starter Solenoid...
Farrar
04-25-2013, 09:48 PM
Thanks, Ron. Given than information, the white/red wire which was cut inside the engine compartment must have been the one for the cold start valve. (The white/red wires on the inside of that connector have been replaced by me.) Since that is not in use on my car, the remaining white/red wire must go to the starter motor.
Farrar
Bitsyncmaster
04-26-2013, 06:51 AM
That was the problem with my car when the CSV never worked. That jumper on the back side of the bulkheads was reading 60 ohms so the CSV never go enough power to open. I just rewired the white/red wires to not use those jumpered pins.
Farrar
05-29-2013, 02:20 PM
I just thought I'd mention in case anyone was still following this thread that after the wire was replaced and the battery charged, all is as it should be. The starter motor turns every time without fail when I turn the key to "start" (as long as the shifter is in "N" or "P").
Thanks, everyone, for all your help!
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.