View Full Version : Transmission 5-Speed Clutch was fine yesterday, went to the floor this morning. Thoughts?
nullset
04-01-2013, 02:08 PM
As the subject says, the clutch was fine yesterday, but when I went to get lunch this morning it dropped to the floor.
Does this sound like a bad slave cylinder? Is there any other possibility before I order a new one?
I can push it down and it will start, but moving it even a minute amount from the bottom causes it to engage.
There's virtually no clutch pressure at all in the pedal.
--buddy
Happened to me a while back - the master cylinder was slowly leaking, and it got to a point where a lot of fluid had leaked out. Replaced both cylinders and everything was fine!
nullset
04-01-2013, 02:33 PM
Happened to me a while back - the master cylinder was slowly leaking, and it got to a point where a lot of fluid had leaked out. Replaced both cylinders and everything was fine!
Where are the master and slave cylinders? I understand that the slave cylinder is under the fuel unit in the engine bay. Where's the master?
If it is low/out of fluid, is filling it a short term fix while I wait on parts?
--buddy
Where are the master and slave cylinders? I understand that the slave cylinder is under the fuel unit in the engine bay. Where's the master?
If it is low/out of fluid, is filling it a short term fix while I wait on parts?
--buddy
I'd rather someone more knowledgeable that me answer that, just in case I get my facts wrong, but have a read here in the meantime:
http://dmctalk.org/showthread.php?5489-Master-clutch-cylinder-HOW-TO&highlight=master+cylinder
LordFly
04-01-2013, 04:17 PM
Where are the master and slave cylinders? I understand that the slave cylinder is under the fuel unit in the engine bay. Where's the master?
If it is low/out of fluid, is filling it a short term fix while I wait on parts?
--buddy
Master is located under the luggage compartment.
If you have a slow leak, topping up the reservoir should fix it temporarily. Just be cautions that it could be empty again the next time you press the clutch. The size of the leak will determine how many presses you get before you're out of fluid again.
Nicholas R
04-01-2013, 06:40 PM
Here is a photo from when I did my auto to manual conversion. The hose is leading down through that slot to the master cylinder. You can see the top bolt of the master cylinder in the photo. The master cylinder is actually bolted to the pedal box and to get onto the head of the bolts, you have to go through the driverside footwell. The clutch pedal is linked to the shaft on the master cylinder.
http://4.bp.blogspot.com/-X5JKi43tOJc/T6aoZgqG16I/AAAAAAAAAvk/X95hd5gIEnY/s1600/Picture+018+%5B1600x1200%5D.jpg
Here is the master cylinder connected to the pedal box before I installed the pedal box.
http://2.bp.blogspot.com/-_SjseKqWHk0/T6aoWHA68aI/AAAAAAAAAvE/U_TZO4BVyKo/s1600/Picture+007+%5B1600x1200%5D.jpg
Here's the other side of the pedal box. You can see the clevis on the master cylinder shaft attaching to the clutch linkage near where the steering column bushing is:
http://2.bp.blogspot.com/-3qpdbNmDD5E/T6aoT9Clh9I/AAAAAAAAAu0/JsKamQDwPLo/s1600/Picture+005+%5B1600x1200%5D.jpg
I have a partially threaded bolt and nut connecting mine, but I think in most cases it is just a pin with a clip attaching the clutch pedal to the master cylinder. If you disconnect the linkage and remove the two bolts, the master cylinder should come off pretty easily. Then you just need to disconnect the clutch line fitting and the hose going to the reservoir.
EDIT: Actually, remove the hoses first, THEN remove the mounting bolts. Otherwise you may not be able to get the clutch line fitting loose.
nullset
04-01-2013, 07:18 PM
The reservoir was bone dry. I topped it off and the clutch appears to be working again. I'm going to keep a close eye on the fluid levels. It probably needs to be flushed anyway. I'll do that in short order.
Is there an easy way to check for leaks? Should I just replace both cylinders?
Thanks,
--buddy
mluder
04-01-2013, 07:43 PM
And if it's completely empty you will need to bleed the system to remove any air pockets. If you don't the clutch function could be impaired.
To bleed it you'll need access to the slave cylindar. - There are how-to's in the formum here.
Cheers
Steven
mluder
04-01-2013, 07:45 PM
The reservoir was bone dry. I topped it off and the clutch appears to be working again. I'm going to keep a close eye on the fluid levels. It probably needs to be flushed anyway. I'll do that in short order.
Is there an easy way to check for leaks? Should I just replace both cylinders?
Thanks,
--buddy
You should also confirm that the original plastic clutch hydrolic line has been replaced with the newer braided stainless steel version. The plastic ones were prone to faileure with temperature swings.
Cheers
Steven
centauri
04-01-2013, 09:00 PM
Be sure to replace both master and slave if there are any doubts, and the braided stainless line is highly recommended. New fluid in an old system that has not been regularly flushed can cause even more damage to the old seals.
congerz83
04-01-2013, 09:22 PM
Be sure to replace both master and slave if there are any doubts, and the braided stainless line is highly recommended. New fluid in an old system that has not been regularly flushed can cause even more damage to the old seals.
100% Correct. If your budget allows, do all three at once. That way, you'll only need to bleed once, and you don't need to worry about future failures.
Fact is, if you have a leak, something is already wrong. If you replace master/slave by itself, often the other component will fail. The old cylinder will often not be able to handle the increased pressure that results from the new "properly sealed" one.
Again, if you can afford, do it all at the same time.
nullset
04-01-2013, 09:58 PM
100% Correct. If your budget allows, do all three at once. That way, you'll only need to bleed once, and you don't need to worry about future failures.
Fact is, if you have a leak, something is already wrong. If you replace master/slave by itself, often the other component will fail. The old cylinder will often not be able to handle the increased pressure that results from the new "properly sealed" one.
Again, if you can afford, do it all at the same time.
I have lots of service records for the car. I'll have to dig through them and see what has and hasn't been done.
--buddy
nullset
04-02-2013, 02:01 PM
The master cylinder is definitely bad.
New master and slave ordered. I already have the stainless line.
I'll be changing it this weekend. Any local owners that want to come by and help out are welcome!
--buddy
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.