Log in

View Full Version : General Brake Fluid Leak?



pezzonovante88
05-08-2013, 03:46 PM
My car is currently up on a rack getting new coolant hoses installed. After removing the fuel tank cover, it's been discovered that something has eaten away the epoxy on the hidden side of the cover. It's all bubbled and eaten away. Has anyone else experienced this? I'm thinking the master cylinder is leaking, but I didn't have time to really look into it. Would this diagnosis make sense?

WelmoedJ
05-08-2013, 05:19 PM
My car is currently up on a rack getting new coolant hoses installed. After removing the fuel tank cover, it's been discovered that something has eaten away the epoxy on the hidden side of the cover. It's all bubbled and eaten away. Has anyone else experienced this? I'm thinking the master cylinder is leaking, but I didn't have time to really look into it. Would this diagnosis make sense?

Don't start thinking of the worst possible.
A PO or his service shop may have been spilling fluid while changing or filling up.
That happened on my car too.

If the bottom of the brake main cylinder is dry, suspect spilling.

Mark D
05-08-2013, 05:23 PM
My car is currently up on a rack getting new coolant hoses installed. After removing the fuel tank cover, it's been discovered that something has eaten away the epoxy on the hidden side of the cover. It's all bubbled and eaten away. Has anyone else experienced this? I'm thinking the master cylinder is leaking, but I didn't have time to really look into it. Would this diagnosis make sense?

My car had both clutch and brake master leaks at one point in time and the brake fluid dripped down the side of the frame and pooled on the fuel tank closing plate. I discovered it far too late and the epoxy was shot in a pretty large area and the steel started to rust.

The most important thing is figuring out where the brake fluid came from. If something is indeed leaking it should be pretty obvious. Check for wetness on the brake master and servo/booster, and check your clutch reservoir line to see if it's in good condition. As the hose that connects the reservoir to the clutch master cyl ages the hose will 'sweat' and eventually start leaking.

Or as Welmoed noted, someone could have done a poor job of topping off the fluids and spilled some brake fluid.

http://dmctalk.org/attachment.php?attachmentid=15742&d=1357280534
http://dmctalk.org/attachment.php?attachmentid=15744&d=1357280570

I suffered some epoxy damage on the frame too. This pic is after some cleanup and rust removal
http://dmctalk.org/attachment.php?attachmentid=13949&d=1349799796

David T
05-08-2013, 05:24 PM
If you are not losing fluid, ie, the level is not going down and you have to add brake fluid, this damage could be from an old leak and the cylinder was replaced already. If you do not see any brake fluid and you aren't leaking any, just remove all of the loose epoxy and repaint the frame and plate.
David Teitelbaum

jawn101
05-08-2013, 09:28 PM
It's so funny how all these cars have the same exact issues. On mine the only spot of rust the whole frame long is right in this exact spot, and it was clearly from an old leaking master as the vacuum booster has drip damage on it as well (under the brand new shiny master). One day I'll get around to cleaning this up too!

DeLorTex
05-08-2013, 10:19 PM
Spent some time under the car today. Discovered the brake leak same way, dropped the gas tank to clean, saw the destruction below. On mine it appears to be a resivoir leak. Res sits inside of 2 rubber grommets in the master. Only evident current leaking seems to have come from the front one of these. Res. slid in and out of the grommets much too easily for my taste. Just startin to research if and how these are replaceable, or does it require a new MC. Meantime- tommorrow its under the car again, this time with a putty knife to scrap off the bubbled frame paint. Anybody replaced these grommets before, and are they even avail.?---- Thanks.

David T
05-09-2013, 10:52 AM
Rare for them to fail, they usually leak because they got damaged during installation. They can be replaced without replacing the master if you can get just the seals.
David Teitelbaum

DeLorTex
05-09-2013, 01:48 PM
Only visible leakage was from below the res. at the front grommet. Resivoir pulled out much too easy, Should have been at least a bit of resistance. Car has been sitting inside garage for a long time. South Texas sun gets temps well over 100 almost every day in the summer in the garage. Guessing-- hoping, they shrunk or hardened from the climate. As I said drip pattern was directly under, any dampness remaining was right under the res. Now to try to find the replacements-- no luck so far.

Mark D
05-09-2013, 02:01 PM
DeLorTex, I've got two reservoir seals that I could remove from my old brake master and ship to you. I bought one of the new units from DMCH so my original master cyl is sitting on a shelf. I can't promise their condition is in much better shape than yours though. The master itself was pretty rusty and pitted inside which is why I replaced it. It didn't appear to be leaking from the connection points to the reservoir though. If you're interested the seals are yours at no charge.

Otherwise I always seem to have luck calling DMCMW for parts like this that aren't normally sold separately.

Henrik
05-09-2013, 02:55 PM
...it's been discovered that something has eaten away the epoxy on the hidden side of the cover. It's all bubbled and eaten away. Has anyone else experienced this?

This is so commonplace that the question should almost be "has anyone NOT experienced this?" I had my fair share of it from a PO but it's been cleaned up since. Last month when I did a brake job, every drop I spilled tried to find its way back to this very spot... :)

DeLorTex
05-09-2013, 08:55 PM
DeLorTex, I've got two reservoir seals that I could remove from my old brake master and ship to you. I bought one of the new units from DMCH so my original master cyl is sitting on a shelf. I can't promise their condition is in much better shape than yours though. The master itself was pretty rusty and pitted inside which is why I replaced it. It didn't appear to be leaking from the connection points to the reservoir though. If you're interested the seals are yours at no charge.

Otherwise I always seem to have luck calling DMCMW for parts like this that aren't normally sold separately.

Thanks Mark thats very kind. I believe I could slip them on the reseviour posts and tell right away if they were tighter. What would you like for compensation? Will they slip into an envelope? I'm heading up to Siren WI. in a short while-- 1 week-- to do some work, but I'll give you an address here to mail to-- Alan Hebzynski, C/O Mike Sawyer 381 Independance . San Benito TX 78586. I'll also call DMCMW and see if they can supply new. Probably won't be able to get back to it for a month. Got a couple days of scrapping, rust treatment and repaint on the frame. Darn, I just did that 15 years ago.

pezzonovante88
05-20-2013, 06:59 PM
Today I started removing all the old crappy epoxy. A lot came off, but there is still a lot on there and it's very stubborn. Any suggestions of how to loosen it up so I can scrape the rest off? Paint thinner, perhaps?

DMCMW Dave
05-20-2013, 07:56 PM
Today I started removing all the old crappy epoxy. A lot came off, but there is still a lot on there and it's very stubborn. Any suggestions of how to loosen it up so I can scrape the rest off? Paint thinner, perhaps?

Propane torch is about the best. Outdoors, it really stinks. Don't let it burn, it will get soft and let go.

David T
05-20-2013, 11:49 PM
It also depends on how far you want to go. All you really have to remove is the stuff that is no longer adhering to the metal. That comes off pretty easily. If you want to remove what is firmly adhering then you need heat, a propane torch, is your best bet but be careful of nearby heat sensitive parts. I say just remove what comes off easily, feather sand the edges, prime the bare metal and spray paint it. If you are working in the area of the fuel tank, it should be removed.
David Teitelbaum

pezzonovante88
05-21-2013, 03:03 PM
I removed it and took it to a powder-coating shop to have it stripped down and re-finished.

Rich
05-22-2013, 10:47 PM
This is so commonplace that the question should almost be "has anyone NOT experienced this?" I had my fair share of it from a PO but it's been cleaned up since. Last month when I did a brake job, every drop I spilled tried to find its way back to this very spot... :)

Good point. It serves notice to all that when servicing the clutch or brake masters or when flushing and topping up it's a good idea to stuff a fat towel or cloth right under the plumbing and above the frame/tank as a dropcloth. It will absorb the fluid before it can reach something with paint on it.

David T
05-22-2013, 10:58 PM
I don't think the problem is so much spilt fluid so much as leaking fluid. When you spill some it will quickly dry up. When the cylinder leaks it leaks slowly so that the area that gets wet is kept wet for a long time. That eventually softens the epoxy and it comes loose from the metal. It is VERY common to see that area under the brake master to get wet and usually when the clutch master leaks it gets under the carpet inside the car. When it is really bad it also gets the paint where the gas tank is and loosens the paint in that area and on the plate. Brake fluid must be really potent to attack epoxy, almost nothing can do that! Not even paint remover!
David Teitelbaum

Trstno1
02-03-2024, 11:08 AM
I have the same sort of leak issue, but coming from the other side. I have fluid leaking from the slave cylinder side. I found bubbled epoxy on the frame rail by the braided ss clutch line in front of the drivers rear wheel. I have also found a very occasional drip onto my drip pan where brake fluid is collecting on the bottom of the transmission, then onto the drip pan. I cannot seem to find the source. When I look up at the trans I see nothing wet up from the where the drip collects. when I look up to the ss braded clutch line connection to the hard pipe going to the slave cylinder, I don't see anything wet. I feel like i have 2 issues. One being a leaking ss cluctch line and maybe a leaking slave cylinder? Will the slave cylinder leak into the trans bell house then onto the bottom of the trans? And has anyone had issues with DMCH ss braided clutch line leaking? I cant seem to track this leak down....

Thoughts on where to look?

WHO1DMC
02-03-2024, 12:33 PM
I have the same sort of leak issue, but coming from the other side. I have fluid leaking from the slave cylinder side. I found bubbled epoxy on the frame rail by the braided ss clutch line in front of the drivers rear wheel. I have also found a very occasional drip onto my drip pan where brake fluid is collecting on the bottom of the transmission, then onto the drip pan. I cannot seem to find the source. When I look up at the trans I see nothing wet up from the where the drip collects. when I look up to the ss braded clutch line connection to the hard pipe going to the slave cylinder, I don't see anything wet. I feel like i have 2 issues. One being a leaking ss cluctch line and maybe a leaking slave cylinder? Will the slave cylinder leak into the trans bell house then onto the bottom of the trans? And has anyone had issues with DMCH ss braided clutch line leaking? I cant seem to track this leak down....

Thoughts on where to look?
If the clutch slave is leaking it's possible for it to get in the clutch it self. Look for fluid on the transmission side of the engine cradle crossmember. When mine leaked I had fluid there.


Dave B.

David T
02-03-2024, 02:31 PM
If the clutch slave is leaking it's possible for it to get in the clutch it self. Look for fluid on the transmission side of the engine cradle crossmember. When mine leaked I had fluid there.


Dave B.

Have an assistant hold the clutch pedal down while you see if you can find the source of the leak. Most likely the seal in the slave cylinder or a connection. If the master cylinder was leaking and was replaced (and the slave was not) it is most likely the slave cylinder that is leaking. If the slave cylinder is leaking you will know as soon as you remove it, it will be very obvious.

r00b
02-03-2024, 05:35 PM
I have the same sort of leak issue, but coming from the other side. I have fluid leaking from the slave cylinder side. I found bubbled epoxy on the frame rail by the braided ss clutch line in front of the drivers rear wheel. I have also found a very occasional drip onto my drip pan where brake fluid is collecting on the bottom of the transmission, then onto the drip pan. I cannot seem to find the source. When I look up at the trans I see nothing wet up from the where the drip collects. when I look up to the ss braded clutch line connection to the hard pipe going to the slave cylinder, I don't see anything wet. I feel like i have 2 issues. One being a leaking ss cluctch line and maybe a leaking slave cylinder? Will the slave cylinder leak into the trans bell house then onto the bottom of the trans? And has anyone had issues with DMCH ss braided clutch line leaking? I cant seem to track this leak down....

Thoughts on where to look?

If you do need a new slave you can get them on ebay https://www.ebay.com/itm/163670165205
don't buy DMCH's junk parts.

82DMC12
02-05-2024, 01:04 PM
If you do need a new slave you can get them on ebay https://www.ebay.com/itm/163670165205
don't buy DMCH's junk parts.

And then you do get this slave cylinder, just send it straight to Rob Grady to get a brass sleeve installed in it. Never worry about your slave cylinder again after he's worked it over.