Log in

View Full Version : Hot start problems



robplus4
05-11-2013, 11:01 PM
I have a hot start problem.
I think I just narrowed down the problem.
I did the "plug swap" and the car started right up.
Can anybody tell me what's the next step. Is it a relay or the cold start valve.

Thank you,
Robert for Temecula, CA

Ron
05-11-2013, 11:16 PM
Sounds like you may have a rest pressure problem. Confirm by pressing down on the air plate to see if it offers resistance for a while after you shut the engine off (it should).
Do a search to find one of many threads here with details. If you get stuck, report back with details.

robplus4
05-12-2013, 01:30 PM
Sounds like you may have a rest pressure problem. Confirm by pressing down on the air plate to see if it offers resistance for a while after you shut the engine off (it should).
Do a search to find one of many threads here with details. If you get stuck, report back with details.

I checked the rest pressure, about 10 min.
Reading the threads pointed me the plug swap.
I replaced accumulator, fuel pump, fuel distributor, warm up regulator, Cleaned fuel injector, Cleaned Cold start Valve, Cleaned frequency valve.

I this helps,
Thanks
Robert

Ron
05-12-2013, 03:05 PM
Was that check (10 minutes) a check you just did...or the longest it holds pressure?
Does it fail to start if you try to restart it immediately?
Have you checked all of your settings? Set the CO last (after making ANY changes including replacement of parts)?

robplus4
05-12-2013, 03:25 PM
Was that check (10 minutes) a check you just did...or the longest it holds pressure?
Does it fail to start if you try to restart it immediately?
Have you checked all of your settings? Set the CO last (after making ANY changes including replacement of parts)?

I checked the rest pressure last week.
It will start within about 4-5 min.
I adjusted co, 2 weeks ago (was hunting, not anymore). note: just smog it 2 weeks ago.
All replacement of parts have been done over the last 6 months.

Ron
05-12-2013, 06:10 PM
Per the manual, the rest pressure should be ~25psi+ after 10 minutes. If it only lasts for 10 minutes you need to find the leak (PPR o-ring, accumulator, pump check valve, injector, CSV, etc). Most will have some pressure for at least a couple of hours...

Bitsyncmaster
05-12-2013, 06:37 PM
I checked the rest pressure last week.
It will start within about 4-5 min.
I adjusted co, 2 weeks ago (was hunting, not anymore). note: just smog it 2 weeks ago.
All replacement of parts have been done over the last 6 months.

Do not adjust the mixture by getting the best idle. You will end up resulting in open loop and to rich. Always use the dwell to center the mixture so you get the best overall running engine. If your idle has problems than try to fix that problem.

robplus4
06-01-2013, 10:08 PM
Per the manual, the rest pressure should be ~25psi+ after 10 minutes. If it only lasts for 10 minutes you need to find the leak (PPR o-ring, accumulator, pump check valve, injector, CSV, etc). Most will have some pressure for at least a couple of hours...

It ended up being a bad check valve.
Goes to show that even a new part can be bad.

Thank you again for all you help.

Robert
Temecula, CA

Ryan S.
06-09-2013, 10:56 AM
This is interesting. I also had a bad check valve but my car didn't start with plug swap. Why? Shouldn't plug swap start the car with rest pressure problem by creating a cold environment when engine is hot? My car never had any cold start problems and it starts fine when engine is cold. So plug swap should work but didn't. Is it because of vaporization of gas prevents car from starting or plug swap doesn't fully create cold environment or something wrong with my car? I am little confused about this.

Second questions
Since it is such a PITA to service fuel accumulator and fuel filter, it would be so nice if they were in the fuel tank access panel area (next to fuel pump). Does our fuel system requires some distances between those three parts in order for it to work? Or was it a cruel joke of Delorean engineers?

19741

Rich
06-09-2013, 01:23 PM
This is interesting. I also had a bad check valve but my car didn't start with plug swap. Why? Shouldn't plug swap start the car with rest pressure problem by creating a cold environment when engine is hot? My car never had any cold start problems and it starts fine when engine is cold. So plug swap should work but didn't. Is it because of vaporization of gas prevents car from starting or plug swap doesn't fully create cold environment or something wrong with my car?

How do you mean you created a cold environment by doing a plug swap with the engine hot? With low/no rest pressure a hot engine with K-Jet can have vaporized fuel in a lot of places. The plug swap doesn't cool the engine off or create a cold environment so the symptoms you describe are normal for a D with a leaky primary fuel system.

Rich
06-09-2013, 01:31 PM
Second question
Since it is such a PITA to service fuel accumulator and fuel filter, it would be so nice if they were in the fuel tank access panel area (next to fuel pump). Does our fuel system requires some distances between those three parts in order for it to work? Or was it a cruel joke of Delorean engineers?

Interesting point.

A few notes and guesses:
- The K-Jetronic fuel system components were likely laid out by the Lotus engineers, not any DeLorean engineers
- The components don't need to be spread out
- The D's frame, designed by Lotus, was set up with places for the filter and the accumulator such that they could be serviced normally by a dealer or mechanic with a lift; no need to pull an access panel to the tank in order to get to them.
- Yes, without a lift it's not easy to access the parts we sometimes need to get to. On the other hand there are loads of shops who can service a K-Jet system - and have a proper lift. The shops will normally not break anything and will warrant their work. Sometimes it pays to have somebody else do the tricky bits. Each owner can figure out what makes sense for their situation, of course.

Ryan S.
06-09-2013, 02:11 PM
How do you mean you created a cold environment by doing a plug swap with the engine hot? With low/no rest pressure a hot engine with K-Jet can have vaporized fuel in a lot of places. The plug swap doesn't cool the engine off or create a cold environment so the symptoms you describe are normal for a D with a leaky primary fuel system.

Rich,
what you say makes sence. So how was OP(Robert) able to start his car with plug swap when he had a check valve issue?
I have had this hot start issue for the last six months and never been able to start my hot engine with the plug swap.

Rich
06-09-2013, 02:35 PM
..So how was OP(Robert) able to start his car with plug swap when he had a check valve issue?
I have had this hot start issue for the last six months and never been able to start my hot engine with the plug swap.

Robert may have been able to start his engine with a plug swap if at the time he started it the engine was cool enough such that any rest pressure requirements were low. His post is unclear about exact conditions when the plug swap worked. The car will start "warm" with a bad check valve or other leak. You just have to be patient at the gas station....

Have you verified that your system is holding rest pressure, either via the metering flap test or any readings? 6 months is a long time to have a hot start problem. It takes a toll on other things, including your patience, no doubt.