View Full Version : Electrical Correct size light bulbs - led/incandescent
krs09
05-17-2013, 05:13 PM
I know this topic has been gone over time and time again but I was hoping to try put the basic info in one place.
Im looking into updating all my lights. The question is what are the correct sizes, weather it be LED or standard incandescent bulbs. Normally I would just pull the old ones and match them up but the PO got so many things wrong I just cant trust him. I wanted to stop by the local auto parts store to check out the sylvania selections but there are so many variations of bulbs I just wasnt sure which way to go.
So, What is the correct size/volt/watt for the Tail lights - Side markers - Reverse lights - Turn signal lights the whole 9yards. I want to get the standard bulbs for now but want to upgrade to leds a little later in the year so I would love to have all this info to price check all our options. Thanks guys, you have yet to let me down. :smile:
DeLorean03
05-17-2013, 09:27 PM
Courtesy of Ozzie (:
http://delorean2109.blogspot.com/2011/07/going-100-leds-on-your-car-is-good-idea.html
krs09
05-17-2013, 11:18 PM
...... :jawdrop: ......
Starglider
05-18-2013, 03:39 AM
Also consider Tomcio's custom DeLorean door lights (http://dmctalk.org/showthread.php?6872-LED-door-and-side-marker-lights).
Bitsyncmaster
05-18-2013, 05:58 PM
One of the great advantages of LEDs that most people forget about is the lack of inrush (cold start) current. An incandescent or halogen bulb cold starting current is 7 to 10 times the normal running current. That current really hurts you with mechanical switch contacts. Think of your 4 25 watt brake lights running through that little switch on the brake peddle. At 7 times the normal current your switching about 50 amps when the lights go on. Now you know why that switch failing is pretty common (mine did when I bought the car).
Now these LEDs with switching regulators probably have an inrush current to charge up the capacitors they use. Wonder what those currents would be.
Ozzie
05-19-2013, 12:23 AM
...... :jawdrop: ......
Thanks!
I've made an update that you may also find handy: http://dmctalk.org/showthread.php?7154-DeLoran-DMC-12-Incandescent-and-LED-Bulb-Reference
David T
05-19-2013, 04:13 PM
The in-rush current on a resistive load (a light bulb) is not all that high and is not even considered typically. Now if you are talking about an inductive load (like a motor) NOW you need to consider in-rush current and locked-rotor current. As bad as in-rush current is, it is the breaking of the connection to an inductive load that destroys contacts because of the arcing. That is what chews up the contact points in the door lock module and the window switches. Think of the electric like water and it has a kind of inertia. It wants to keep going even when you break the connection. That is what causes the arcing and the heat from that arcing melts the contacts. One way to reduce the problem is to increase the size and number of contact points to spread the heat out. We can get to complicated on this subject. Bottom line, LED's are great because they use so little electric and they last a LONG time. Brake switches fail prematurely usually because they are not installed or adjusted correctly.
David Teitelbaum
Bitsyncmaster
05-19-2013, 04:53 PM
David there are many documents that document why the incandescent bulbs had a very high cold start current.
Here is one:
http://www.lamptech.co.uk/Documents/IN%20Starting.htm
But all you need to do is measure the bulb resistance with your ohm meter. Now divide that resistance in ohms into the voltage that you will apply and the result is the current in amps.
David T
05-19-2013, 05:42 PM
That is one way to do it but when you use a multi-meter you are only using a couple of volts. The resistance does change vs voltage during in-rush. As an engineering calculation in-rush current tends to be disregarded for resistance loads like dryers, heat, and lighting. It becomes important when dealing with inductive loads like transformers and motors. Especially when dealing with AC. DC is a simpler case and can be more easily calculated and measured. Anyway, no one is saying you should be replacing incandescent bulbs with LED's because of the lower in-rush current. Not significant. Especially when compared against the longer life and lower current draw.
David Teitelbaum
Bitsyncmaster
05-19-2013, 06:46 PM
That is one way to do it but when you use a multi-meter you are only using a couple of volts. The resistance does change vs voltage during in-rush. As an engineering calculation in-rush current tends to be disregarded for resistance loads like dryers, heat, and lighting. It becomes important when dealing with inductive loads like transformers and motors. Especially when dealing with AC. DC is a simpler case and can be more easily calculated and measured. Anyway, no one is saying you should be replacing incandescent bulbs with LED's because of the lower in-rush current. Not significant. Especially when compared against the longer life and lower current draw.
David Teitelbaum
I'm saying you should replace the brake lights with LEDs because of inrush current. I would bet a new brake light switch with LEDs would never burn out. Of course the major reasons are the speed of illumination, deeper colors, and longer life.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.