View Full Version : Engine 3.0 Swap - doing it a little different
So, I have a hole in the valley, which is causing a severe oil leak. After researching I have found this has happened to others as well, and there are solutions. I have seen filling the holes with epoxy, jb welding on plates, and hodge podge setups clamping those plates down. I have also seen plates welded over the holes in the block, this is the route I will go if I fix my block.
However, I did a quick search on the local classified ads, and a gentleman about 200km away from me has a 1990 premier engine sitting in his garage for a fairly reasonable price. Which gets me to thinking, perhaps a engine swap might be a better idea than welding on my block, as cast aluminum is less than ideal to be welding to. Expecially when it was coated with oild and antifreeze for the last decade.
I am fully aware with the custom spark/fuel system needing to be implemented, and if I were to spend the money on that I would rather just spend the money on a different engine and doing a custom swap.
As I have read, the problems stem from swapping over the lower casings and losing the knock sensor. The mounts on the 3.0 are similar to the delorean but a few inches forward as show in the attached pictures.
I would love to keep the stock wiring and ecm, for cost and reliability and have no problem fabricating custom mounts. The new mounts would overhang the frame so I would incorporate some gusseting and maybe a new mounting point.
So my question is, does this seem feasible? Assuming I make mounts that will mount the 3.0 casing to the delorean frame; which I am 100% certain I can successfully do.
chris williams
05-21-2013, 04:08 PM
as cast aluminum is less than ideal to be welding to. Expecially when it was coated with oild and antifreeze for the last decade.
I did try this, (well had an expert weld the holes up) whilst it looked a really good job, and was. The oil just forced it's way out of any tiny hole and through the 'ribs' into the other holes in the valley. Eventually had to change the block to a Volvo one. Clearly this is the route I should have took in the first place:rolleyes1:
Chris
dmc6960
05-21-2013, 04:17 PM
I would love to keep the stock wiring and ecm, for cost and reliability and have no problem fabricating custom mounts. The new mounts would overhang the frame so I would incorporate some gusseting and maybe a new mounting point.
So my question is, does this seem feasible? Assuming I make mounts that will mount the 3.0 casing to the delorean frame; which I am 100% certain I can successfully do.
Regarding the custom mounts, it has been done once before but I would not recommend it. Bill Robertson, no longer on this list, fabricated mount "extensions" to work with this form of mounting ear from a crate engine he installed.
The biggest problem though will be your fuel and ignition. The stock eagle crank pickup is attached to the flexplate. One person here tried transplanting it onto a DeLorean flywheel, but with no luck. You'll very likely need to do a custom engine management system for ignition and fuel.
I do not believe loosing a mount for a knock sensor from swapping lower cranks is a big deal. That can be remounted if necessary in other ways.
Regarding the custom mounts, it has been done once before but I would not recommend it. Bill Robertson, no longer on this list, fabricated mount "extensions" to work with this form of mounting ear from a crate engine he installed.
The biggest problem though will be your fuel and ignition. The stock eagle crank pickup is attached to the flexplate. One person here tried transplanting it onto a DeLorean flywheel, but with no luck. You'll very likely need to do a custom engine management system for ignition and fuel.
I do not believe loosing a mount for a knock sensor from swapping lower cranks is a big deal. That can be remounted if necessary in other ways.
Yes I had heard about Bill's mounts. How they overhang they could easily be done incorrectly. I was under the assumption the only sensor was the knock sensor that was lost when switching over casings. There is another sensor proprietary to the eagle auto trans then?
EDIT: Just looked it up, I was incorrect. There is a knock sensor in the block monitoring the crankshaft and a crankshaft position sensor in the bellhousing monitoring the position of the flexplate. hmm.
I did try this, (well had an expert weld the holes up) whilst it looked a really good job, and was. The oil just forced it's way out of any tiny hole and through the 'ribs' into the other holes in the valley. Eventually had to change the block to a Volvo one. Clearly this is the route I should have took in the first place:rolleyes1:
Chris
Thanks for the input Chris. I had a feeling this might happen, but I figured it would be low enough pressure it would not be a concern. I guess I was wrong. Hmm. Any pictures of the repair?
I got a few bits and pieces of info from this thread. It seems people are thinking the knock sensor is the crankshaft position sensor, Once again correct me if I'm wrong just trying to get this sorted out.
http://dmctalk.org/showthread.php?4020-3-0-PRV-Swap-Basics-Overview-Question
Morpheus
05-21-2013, 06:43 PM
I would be willing to sell you my 2.8 block if you are interested. It has just been freshly hot-tanked and it's in good shape.
I would be willing to sell you my 2.8 block if you are interested. It has just been freshly hot-tanked and it's in good shape.
Thanks for the offer Brandon! However This would require rebuilding my current 2.8 which would be pointless as far as I am concerned. Lots of money to do it properly (all new gaskets, pistions, rings, and many other parts) and you still end up with a 130hp engine with a very outdated fuel injection system and troublesome wiring and electronics. I know many will disagree with me but I am not exactly a purist! haha.
Spittybug
05-21-2013, 08:06 PM
Several of us with Megasquirt EFI experience at this point. If you change engines and fueling systems, we can assist.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.