PDA

View Full Version : How do I wire a switch up to the hot start relay plug so I can start the car inside.



robplus4
05-22-2013, 07:11 PM
I'm having trouble stating the car when it's warm.
How do I wire a switch up to the hot start relay plug so I can start the car from inside the car.

Thanks

Bitsyncmaster
05-22-2013, 07:42 PM
I'm having trouble stating the car when it's warm.
How do I wire a switch up to the hot start relay plug so I can start the car from inside the car.

Thanks

I have a solid state hot start relay. It turns the CSV on after your engine has cranked for 1 second. If you keep cranking with no start it will turn off the CSV after 4 seconds. Just plug it into hot start relay socket. PM me if you want to buy one.

SS Spoiler
05-22-2013, 08:21 PM
Dave could you put a list of the electrical improvements that you have come up with descriptions and prices?
It's probably in the archives somewhere........thanx

Bitsyncmaster
05-22-2013, 08:26 PM
Dave could you put a list of the electrical improvements that you have come up with descriptions and prices?
It's probably in the archives somewhere........thanx

My web site shows most everything except the price. PM me for a price list.

DMCMW Dave
05-22-2013, 08:44 PM
On the white empty socket in the relay compartment there are 3 wires. If you connect the white/red to the Blue/black the cold start injector will fire whenever the starter is cranking. Don't just put in a jumper or most of the time you'll flood the engine. But a pushbutton switch will come in handy.

The factory intended a relay that would pulse the cold-start only when very hot, but I don't believe that they ever came up with the actual part. Dave Bitsyncmaster has apparently invented one.

David T
05-22-2013, 11:21 PM
Wiring a pushbutton or sticking in a relay is only going to get you past the symptom. While it can get you going the best repair is to find and fix the cause of the hard, hot restart problem. 90% of the time it is going to be a bad accumulator or a bad fuel pump check valve.
David Teitelbaum

Mark D
05-23-2013, 12:43 PM
Wiring a pushbutton or sticking in a relay is only going to get you past the symptom. While it can get you going the best repair is to find and fix the cause of the hard, hot restart problem. 90% of the time it is going to be a bad accumulator or a bad fuel pump check valve.
David Teitelbaum

At one point in time the previous owner of my car had hooked up a switch as Dave was describing due to a hot start issue. Eventually the PO got tired of having to hit the switch everytime he started the car and replaced the accumulator to solve the root problem.

The switch was kind of a cool workaround, but I agree that it's better to solve the real issue than band-aid the situation.

The switch will get you buy in a pinch though so you're not stuck sitting there waiting for the engine to cool down before you can restart it. I still keep the switch box with me in case of a future issue but it's no longer plugged in.

David T
05-23-2013, 02:27 PM
I can agree putting in a switch is convenient but doing the plug swap is not all that difficult and it will get you going so you are not stuck or have to wait till the motor cools down.
David Teitelbaum

Bitsyncmaster
05-23-2013, 05:53 PM
I can agree putting in a switch is convenient but doing the plug swap is not all that difficult and it will get you going so you are not stuck or have to wait till the motor cools down.
David Teitelbaum

If you don't mind the embarrassment.

DMCMW Dave
05-23-2013, 08:23 PM
If you don't mind the embarrassment.

And wearing out the connectors.

David T
05-23-2013, 10:40 PM
And wearing out the connectors.

I was thinking to only do the plug swap if all of a sudden you have a hard hot restart. It would keep you from being stuck and when you can get the chance you would fix the rest pressure problem. I am not recommending the plug swap as a permanent type of fix instead of wiring in a switch. And I am not recommending putting the switch in. What I am saying is the switch is not necessary if you have a hard hot restart and you get it fixed soon. The plug swap will get you going in the meantime. The central point to be made here is that my advice is not to fix the symptom (by putting in a switch or swapping plugs) but to fix the problem. All too often that is what happens though, put another Band-Aid on top of a problem and the customer is happy. Especially if putting in a switch is $5 and putting in an accumulator is $100. As for embarrassment, you would be a lot more embarrassed if you couldn't get the car started! Yes, you had to fiddle with the car but at least you got it going.
David Teitelbaum

robplus4
05-24-2013, 01:24 AM
I was thinking to only do the plug swap if all of a sudden you have a hard hot restart. It would keep you from being stuck and when you can get the chance you would fix the rest pressure problem. I am not recommending the plug swap as a permanent type of fix instead of wiring in a switch. And I am not recommending putting the switch in. What I am saying is the switch is not necessary if you have a hard hot restart and you get it fixed soon. The plug swap will get you going in the meantime. The central point to be made here is that my advice is not to fix the symptom (by putting in a switch or swapping plugs) but to fix the problem. All too often that is what happens though, put another Band-Aid on top of a problem and the customer is happy. Especially if putting in a switch is $5 and putting in an accumulator is $100. As for embarrassment, you would be a lot more embarrassed if you couldn't get the car started! Yes, you had to fiddle with the car but at least you got it going.
David Teitelbaum

Thanks David,

Little history.
Did plug swap, car started right up
Replaced accumulator
Replaced fuel pump with fuel check valve
Replaced fuel distributor
Replaced WUR
Replaced CSV
Replaced o-ring in distributor (2 times)
Cleaned injectors
Cleaned FV

Rest pressure about 10 min.

Ron
05-24-2013, 02:09 AM
In your other thread, you mentioned adjusting the CO because it was hunting -- You used a dwell meter rather than turning the adjustment enough to cure the hunting, right?

Try putting your injectors (including the CSV) in a container and seeing if they leak when you energize the pump.
(You can not trust them just because you sent them out to be cleaned...at all!)

robplus4
05-24-2013, 02:27 AM
In your other thread, you mentioned adjusting the CO because it was hunting -- You used a dwell meter rather than turning the adjustment enough to cure the hunting, right?

Try putting your injectors (including the CSV) in a container and seeing if they leak when you energize the pump.
(You can not trust them just because you sent them out to be cleaned...at all!)

Hi Ron,

I adjusted CO by having the FV cycling on/off about every 3 to 4 seconds.

Thank you for your help.
Robert

Ron
05-24-2013, 02:35 AM
You need to do it with a dwell meter.
In any case, the FV will buzz constantly any time the CO setting is close, so it can't be right.
If it is set too rich, that could be the source of you pressure leak (via the injectors).

It's easy to do -- Read this thread
http://dmctalk.org/showthread.php?5760-Adjusting-CO-With-A-Dwell-Meter

Bitsyncmaster
05-24-2013, 05:05 AM
Rest pressure about 10 min.

Only 10 min. hold of rest pressure will cause hot start problems.

David T
05-24-2013, 10:50 AM
Only 10 min. hold of rest pressure will cause hot start problems.

I understand you spent a lot of time and money replacing parts and you still have the hard hot restart. The problem is that one or more of the replacement parts is defective or improperly installed. My first suspect would be the fuel pump check valve. I would not give up and stick in the switch although you could do it temporarily till you find and fix the problem for good. That way you could still drive the car and not worry about wearing out plugs and connectors. Just do not consider the switch a solution to the problem.
David Teitelbaum

robplus4
05-24-2013, 02:16 PM
I understand you spent a lot of time and money replacing parts and you still have the hard hot restart. The problem is that one or more of the replacement parts is defective or improperly installed. My first suspect would be the fuel pump check valve. I would not give up and stick in the switch although you could do it temporarily till you find and fix the problem for good. That way you could still drive the car and not worry about wearing out plugs and connectors. Just do not consider the switch a solution to the problem.
David Teitelbaum

Just pulled the fuel pump, there was fuel in the return line.
Is this normal?

DMCMW Dave
05-24-2013, 03:04 PM
Just pulled the fuel pump, there was fuel in the return line.
Is this normal?

Yes, it is a fuel line so there should be fuel in it.

Bitsyncmaster
05-24-2013, 03:09 PM
To find your problem, I would make up a pressure gauge that could connect to the feed hose going to the FV. So you would remove that end on the FV, connect it to the guage, run the pump for a few seconds then test the rest pressure time. If it still is only 10 min then you need to back up your testing (accumulator, filter, pump).

David T
05-24-2013, 09:49 PM
To find your problem, I would make up a pressure gauge that could connect to the feed hose going to the FV. So you would remove that end on the FV, connect it to the guage, run the pump for a few seconds then test the rest pressure time. If it still is only 10 min then you need to back up your testing (accumulator, filter, pump).

Another way to test if it is the fuel pump check valve would be to put a manual valve into the return line and after you shut the motor down, shut the valve and see if it will hold rest pressure. If it does, your check valve is bad.
David Teitelbaum

Ron
05-24-2013, 11:34 PM
Me thinks not.

DMCMW Dave
05-25-2013, 12:25 AM
Me thinks not.

Does seem like a lot of work (cutting the line, or finding matching fittings on a generic valve etc.). Not sure how you would really (practically) do this.

David T
05-25-2013, 12:14 PM
Does seem like a lot of work (cutting the line, or finding matching fittings on a generic valve etc.). Not sure how you would really (practically) do this.

You could make up a valve with a couple of fittings and connect it where the hard fuel line connects to the fuel pump. Or get an old hose (the one that connects the fuel pump to the hard line) cut it, and insert a valve. Now, for testing purposes you just use your "test hose" with the valve in it. It wouldn't be that difficult. Another quick and "dirty" test would be to just clamp that hose and see what happens. Two problems with that though, one, you can't be sure you have it clamped off completely and two, you could crush and damage the hose.
David Teitelbaum

LEVY
05-26-2013, 09:46 AM
Another way to test if it is the fuel pump check valve would be to put a manual valve into the return line and after you shut the motor down, shut the valve and see if it will hold rest pressure. If it does, your check valve is bad.
David Teitelbaum

Not sure how the fuel system is routed, but if it is the way I think it is, by inserting a valve on the return line you are not testing anything, the original check valve is still used. I may be wrong.


LEVY

Ron
05-26-2013, 10:48 AM
:hihi2:

Bitsyncmaster
05-26-2013, 12:01 PM
Not sure how the fuel system is routed, but if it is the way I think it is, by inserting a valve on the return line you are not testing anything, the original check valve is still used. I may be wrong.


LEVYIf you had a shut off valve (or clamp the hose) it could test the PPR for leaking (pump off). Could also test every thing for busting pressure (pump on).

LEVY
05-26-2013, 12:01 PM
:hihi2:

I may not always be right, but I'm never wrong! :D

LEVY
05-26-2013, 12:08 PM
If you had a shut off valve (or clamp the hose) it could test the PPR for leaking (pump off). Could also test every thing for busting pressure (pump on).

Still don't get it, how can you check anything with a valve on the return line?
Unless you know for sure you have a good check valve, it will be very hard to tell where the leak is, if any.

LEVY

Bitsyncmaster
05-26-2013, 12:27 PM
Still don't get it, how can you check anything with a valve on the return line?
Unless you know for sure you have a good check valve, it will be very hard to tell where the leak is, if any.

LEVY

You still would not know if the leak was elsewhere, but if it fixed your rest pressure you would know it's the PPR or FV that is leaking.

LEVY
05-26-2013, 12:42 PM
Another way to test if it is the fuel pump check valve would be to put a manual valve into the return line and after you shut the motor down, shut the valve and see if it will hold rest pressure. If it does, your check valve is bad.
David Teitelbaum


You still would not know if the leak was elsewhere, but if it fixed your rest pressure you would know it's the PPR or FV that is leaking.

Sounds better but, can you test the check valve by following David T description above?

To me, if you have a bad check valve, still will lose presure if using this technique.

LEVY

Bitsyncmaster
05-26-2013, 01:06 PM
Sounds better but, can you test the check valve by following David T description above?

To me, if you have a bad check valve, still will lose presure if using this technique.

LEVY

True. If the test did not fix the rest pressure time, you only know it's not the PPR or FV.

Dangermouse
05-26-2013, 02:25 PM
Would the manual valve not need to be on the supply line to test the check valve?

LEVY
05-26-2013, 02:44 PM
Would the manual valve not need to be on the supply line to test the check valve?

You got it!

Just waiting for a reply (excuse) from you know who! :D

David T
05-26-2013, 10:10 PM
You got it!

Just waiting for a reply (excuse) from you know who! :D

Hi, waiting for me? The answer to your question is you put a valve AFTER the fuel pump in the supply line to test the check valve. As for testing for bursting pressure, you would shut the pump off first and then close the valve. To test the PPR you would put the valve in the return line (I may have mixed them up in a previous post, oops). Again, you would shut the valve only after you shut the pump off. In another thread the poster used a "C" clamp. Not as elegant but you do not have to undo any connections. As long as you know you have sufficiently blocked the line so it is not leaking and you don't collapse it. IMHO it is rare to have a problem with the PPR unless you have changed the original "O" rings. Much more likely the check valve is the problem. Even if it has been replaced!
David Teitelbaum

robplus4
06-01-2013, 10:04 PM
Sounds better but, can you test the check valve by following David T description above?

To me, if you have a bad check valve, still will lose presure if using this technique.

LEVY

Well, it ended up being a bad check valve.
It go's to show even a new part can be bad.

I want to thank everybody for all the help.

Thank you everybody.

Robert
Temecula, Ca

Azar
10-17-2021, 11:56 AM
On the white empty socket in the relay compartment there are 3 wires. If you connect the white/red to the Blue/black the cold start injector will fire whenever the starter is cranking. Don't just put in a jumper or most of the time you'll flood the engine. But a pushbutton switch will come in handy.

The factory intended a relay that would pulse the cold-start only when very hot, but I don't believe that they ever came up with the actual part. Dave Bitsyncmaster has apparently invented one.
Hi Dave, are these definitely white/red and the Blue/black? I red somewhere else that it is blue/black and black... Thanks!

Bitsyncmaster
10-17-2021, 02:18 PM
Hi Dave, are these definitely white/red and the Blue/black? I red somewhere else that it is blue/black and black... Thanks!

Blue/black to Black is correct. The hot start relay grounds that blue/black when engine is cranking.

Azar
10-17-2021, 02:31 PM
Blue/black to Black is correct. The hot start relay grounds that blue/black when engine is cranking.Thanks, checked with the Diagramm already. The other one is 12V [emoji2]