PDA

View Full Version : Suspension Steering rack questions.



Mydmc5898
05-28-2013, 05:39 PM
I'm about done with a lot of the hardware issues with my car.
The two items left is the lower ball joints which don't have play, but I'd rather replace them being 30+ years old.
And the steering rack.

I never had any issues with the steering, so I guess I'm looking for opinions.
One day I was leaving work and the rack was fine, I had to make a sharp left turn. It felt like the rack got stuck.
It was much harder to turn. Then it loosened up again and got hard again. After letting the car sit. I started it up and it was fine again, it hasn't acted up since. Maybe 3 weeks now it's been good.
The only maintenance I ever had done on the rack was replaced the boos and filled it with gear oil.
I heard a metallic sound coming from the car the other night but that seemed to have also gone away.
And honestly the rack seems fine.
I was going to replace the tire rod ends as well, no play, but the boots on those are rotted as well.
I noticed one of my clamps came off the rack hoping the boot in place and it's evident the rack leaked out hear oil.
Is it advisable to pull the new boots back, refill with oil and let it go?
Or should I just bite the bullet and replace the rack?

-Darryl

wrkey
05-28-2013, 06:04 PM
My car was sitting for a little over 6 years when I acquired her. She has <14k miles on her. The rack seemed okay at first.. but then the joints fell apart because of the rust and old bearings and etc., etc. I purchased the rack from DMCH for $250 plus a core charge and installed it. The rack comes complete so you get new tie rod ends, boots, rubber bushings, etc. So if you're thinking of replacing the ends, boots, rubber bushings, and that there 'might' be issues.. I suggest you just do the whole things.

It's very easy to replace.. put your car on jacks and set the steering to straight head and the wheel centered. Mark Top Dead Center of the steering column connection that you can access through the cover in the truck. Mark TDC on the current rack spline as well. Pull the tires, drop the tie rod ends, disconnect the steering shaft at the spline, 4 bolts for rack brackets and pull the rack out through the driver's side. Find center on your new rack (turn it to lock one way, then the other then go back half way) and mark TDC. Set the racks next to each other and adjust the new tie rods to where they are the same length as the old (with it at TDC). Install is reverse of removal. Unfortunately, the steering shaft only fits onto the spline one way so that the bolt can pass where the splines are 'missing' and this will most likely put your steering when in a position other than the flat level that you are used to. But.. you don't have a choice as you have to set the steering wheel into the correct position AFTER the new rack is installed and the front is aligned. You can probably get the alignement folks to set the steerin wheel for you ... if they have the right bolts. If not, you can find how to that on other posts here.

Anyway, not a detailed outline but just enough to show how I did it and to recommend the complete rack replacement.

Good luck!



I'm about done with a lot of the hardware issues with my car.
The two items left is the lower ball joints which don't have play, but I'd rather replace them being 30+ years old.
And the steering rack.

I never had any issues with the steering, so I guess I'm looking for opinions.
One day I was leaving work and the rack was fine, I had to make a sharp left turn. It felt like the rack got stuck.
It was much harder to turn. Then it loosened up again and got hard again. After letting the car sit. I started it up and it was fine again, it hasn't acted up since. Maybe 3 weeks now it's been good.
The only maintenance I ever had done on the rack was replaced the boos and filled it with gear oil.
I heard a metallic sound coming from the car the other night but that seemed to have also gone away.
And honestly the rack seems fine.
I was going to replace the tire rod ends as well, no play, but the boots on those are rotted as well.
I noticed one of my clamps came off the rack hoping the boot in place and it's evident the rack leaked out hear oil.
Is it advisable to pull the new boots back, refill with oil and let it go?
Or should I just bite the bullet and replace the rack?

-Darryl

Mydmc5898
05-28-2013, 06:19 PM
I bought my car in 2001. I know it sat from 1983-1997, then from 2000-2001 until I bought it. I had documents showing it was serviced in between those dates.

The longest it sat was about 3 years after I bought it.
I bought it with 30k ok it, now it has 46k on it. Maybe a little more, angle drive failed a few times.

It was stored in doors every time not in use, however doesn't mean it didn't deteriorate in some manner.
Guess it's better to replace it to be safe then have it fail on me.

Alrighty and thanks too, I will replace the surroundings parts as well.

Thanks again,
Darryl

David T
05-28-2013, 11:40 PM
I would check out the two universal joints from the steering column. They may be causing your sticking problem. As for the lower ball joints, if they are tight and the dust boots are not torn I would just lubricate them.
David Teitelbaum