View Full Version : Changing the bushings on the shifter mechanism.
Ozzie
05-26-2013, 12:53 PM
This morning, I had one of the most different rides on the DeLorean since I've owned it. I followed Mike's (the Lotus Guy, Mike) recent tip to change out the shifter bushings. Did it (and inexpensive and quick job) and the results changed how our DeLorean drives. The old bushings were in fact worn, so now it shifts SO much smoother. Thanks, Mike. I documented the procedure/tips/notes here, if anyone else in interested:
19260
Smooth shifting on a 30+ year old car (http://delorean2109.blogspot.com/2013/05/smooth-shifting-on-30-year-old-car.html)
DMC5180
05-26-2013, 07:34 PM
Nice Job Ozzie.
I did this job on a friends car about ten years ago. I was recently under my own car doing linkage adjustments and noticed the Transmission end rubber bushing was in tough shape. prompting me to consider replacing all mine in the near future.
Bitsyncmaster
05-26-2013, 09:04 PM
I did all my rubber shift bushings when I redsigned the hard bushing mounting. Mine looked like the new ones so I guess someone had changed them before.
Jacko
05-26-2013, 09:26 PM
Ironically, the very first non-scheduled maintenance on 4915 (at 50,000 miles) was replacing these little bushings and yes, it made a real difference.The steering wheel notwithstanding, the shifter is the driver's main link to the car ... if the shifter is sloppy the car doesn't feel right.
dmc6960
05-27-2013, 01:52 AM
I changed out all of my bushings when I did my engine rebuild in 2009. Apparently my car is the exception, not the norm with many typical failure points. My old 100,000 mile bushings really weren't all that bad compared to the new ones (though my car was completely missing one of the "top hats" that go around them). I didn't notice a significant improvement afterwards ( was already very decent to begin with), but I did go over a year without driving it. So my perception may be impaired.
My shifter is very stiff. I just removed the Transmission and there is still more resistance than any standard I have driven. So replacing the bushings is the answer?
Just to see if i am correct, the parts you guys are refering to are #100776 (qty 8 ) and #100775 (qty 4)
dmc6960
05-27-2013, 02:33 AM
These bushing ls cause more slop than resistance. If your shifter is very tight, it could be the primary pivot bolt is tightened too much causing the resistance.
These bushing ls cause more slop than resistance. If your shifter is very tight, it could be the primary pivot bolt is tightened too much causing the resistance.
Thanks for the tip! I will loosen it and see how it feels. I figured there may also be some resistance in the shifter assembly, but I don't see how it can be serviced.
jawn101
05-27-2013, 11:18 PM
Thanks for the tip! I will loosen it and see how it feels. I figured there may also be some resistance in the shifter assembly, but I don't see how it can be serviced.
The shifter can be serviced by removing the center console (or at a minimum the trim plate around the shifter), disconnecting the crossgate cable and shifter tube, then removing the gearchange assembly. Only 4 bolts holding it down. But it's a pretty static assembly, your main task will be to clean it thoroughly and then lubricate all the metal-metal joints.
Mine was pretty bent up when we removed it but Clint was able to correct the bend. That plus all new bushings in the shift linkage front to back and a completely rebuilt transmission have given me cause to question *anyone* who says the DeLorean "just has" a sloppy shift. Mine is as precise and positive as a bolt action rifle now.
Replacing the bushings is a GREAT start. Keep an eye out for the plastic half-sleeves that go inside the bushings too. Those may be gone but they are important to prevent the bolts from just tearing the bushings up instantly. Cleaning and re-lubing the shifter mechanism is another good move. Adjust your gearchange tubes and crossgate cable for the best engagement. Don't loosen (or tighten!) your pivot bolt too much or you risk putting strain on the threaded portion instead of the shoulder, which can lead to the bolt snapping, which would lead to a Very Bad Day.
The shifter can be serviced by removing the center console (or at a minimum the trim plate around the shifter), disconnecting the crossgate cable and shifter tube, then removing the gearchange assembly. Only 4 bolts holding it down. But it's a pretty static assembly, your main task will be to clean it thoroughly and then lubricate all the metal-metal joints.
Mine was pretty bent up when we removed it but Clint was able to correct the bend. That plus all new bushings in the shift linkage front to back and a completely rebuilt transmission have given me cause to question *anyone* who says the DeLorean "just has" a sloppy shift. Mine is as precise and positive as a bolt action rifle now.
Replacing the bushings is a GREAT start. Keep an eye out for the plastic half-sleeves that go inside the bushings too. Those may be gone but they are important to prevent the bolts from just tearing the bushings up instantly. Cleaning and re-lubing the shifter mechanism is another good move. Adjust your gearchange tubes and crossgate cable for the best engagement. Don't loosen (or tighten!) your pivot bolt too much or you risk putting strain on the threaded portion instead of the shoulder, which can lead to the bolt snapping, which would lead to a Very Bad Day.
Thanks for the info Jon! I will disassemble my shifter and linkage and clean it up, as well as inspect the bushings. I will have to adjust the cross gate cable when I re-install my transmission; I found a very good youtube video explaining how. I will be careful with the pivot bolt.
Thanks again!
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.