Log in

View Full Version : Brake Questions About Bleeding the Brakes



uhhair
05-31-2013, 10:35 PM
Okay so I've got my brake system rebuilt completely, and I'm onto bleeding the brakes. I bled the brakes, but they still don't feel right.

With the car on, when I push the brakes they go almost to the floor, and it's not too terribly hard to press down.

If I pump the brake very quickly, it becomes hard as a rock instantly. If I let off the brake for a few seconds then push again though, it feels softer again and goes to the floor.

With the car off, after pumping them a few times (like the manual says in the bleeding procedures), they feel pretty hard.

Is this a sign that there is just some air in the lines still somewhere I need to bleed out? Hoping so!

David T
05-31-2013, 11:17 PM
You still have air in the system. Make sure the master cylinder is completely bled first. Best done on a bench.
David Teitelbaum

uhhair
05-31-2013, 11:25 PM
All of the previous threads on here indicate you don't need to bench bleed the master, since it sits basically level in the car. Also, not certain I know how to do that.

Ozzie
06-01-2013, 12:34 AM
I recall that jacking the rear up when bleeding the rear calipers, helped to bleed out trapped air well. This is because in this position, the rear bleeding points are then higher than the master cylinder - which will is where trapped air will go to (the highest point in the system). Hope that helps.

DMCMW Dave
06-01-2013, 02:20 PM
Are the pads new?

dmc6960
06-02-2013, 02:10 AM
Are the pads new?

Curious if this question relates to the piston's position in the caliper? Do worn pads or new pads make for better bleeding?

Tillsy
06-02-2013, 05:11 AM
Curious if this question relates to the piston's position in the caliper? Do worn pads or new pads make for better bleeding?

Based on the amount of crap and old fluid I found when I rebuilt each of my callipers I'm going to guess Dave may be about to suggest that a full bleed doesn't flush ALL the fluid that could be built up if the pistons are extended due to worm pads?

uhhair
06-02-2013, 12:34 PM
Yeah, we got it figured out. We just bled them a second time and now they're perfect. Probably just didn't get all the air out on the first take.

Mark D
06-03-2013, 12:07 PM
I recently bled my brakes after doing a full brake system rebuild also...new master, rebuilt calipers, flushed brake lines, etc. The system was bascially empty when I started. I built a pressure bleeder per the recommendation of Dave and it made the process much easier. No bench bleeding of the master cyl required. Here were the general instructions I followed to build one.

http://www.bmw-m.net/TechProc/bleeder.htm

Basically all it does is provide air pressure to the reservoir on top of the master cylinder to push the brake fluid through the system. It was an ideal solution for me since I was doing all the work myself without a helper to pump the brakes while I opened the bleed screws. The order I worked from was RRear,LRear,RFront,LFront. I also pumped the brake pedal by hand while air pressure was being supplied to the reservoir to help speed up the process of working out all the air.

Total spent was about 40 bucks to build the pressure bleeder. The sprayer bottle I used was $10 on sale from the local hardware store, and I used a "Help!" reservoir cap from Auto Zone with a hole drilled in it and some brass fittings. The pressure gauge was the most expensive part of the build at $15. If I had shopped around a little more I probably could have found a cheaper one with a lower pressure range on the dial. I only pressurized the tank to 15-20psi

http://dmctalk.org/attachment.php?attachmentid=19429&d=1370271672
http://dmctalk.org/attachment.php?attachmentid=19430&d=1370271675
http://dmctalk.org/attachment.php?attachmentid=19431&d=1370271678

Minkman
07-21-2013, 05:02 PM
I recently bled my brakes after doing a full brake system rebuild also...new master, rebuilt calipers, flushed brake lines, etc. The system was bascially empty when I started. I built a pressure bleeder per the recommendation of Dave and it made the process much easier. No bench bleeding of the master cyl required. Here were the general instructions I followed to build one.

http://www.bmw-m.net/TechProc/bleeder.htm

Basically all it does is provide air pressure to the reservoir on top of the master cylinder to push the brake fluid through the system. It was an ideal solution for me since I was doing all the work myself without a helper to pump the brakes while I opened the bleed screws. The order I worked from was RRear,LRear,RFront,LFront. I also pumped the brake pedal by hand while air pressure was being supplied to the reservoir to help speed up the process of working out all the air.

Total spent was about 40 bucks to build the pressure bleeder. The sprayer bottle I used was $10 on sale from the local hardware store, and I used a "Help!" reservoir cap from Auto Zone with a hole drilled in it and some brass fittings. The pressure gauge was the most expensive part of the build at $15. If I had shopped around a little more I probably could have found a cheaper one with a lower pressure range on the dial. I only pressurized the tank to 15-20psi

http://dmctalk.org/attachment.php?attachmentid=19429&d=1370271672
http://dmctalk.org/attachment.php?attachmentid=19430&d=1370271675
http://dmctalk.org/attachment.php?attachmentid=19431&d=1370271678

Any secret to keeping fluid from leaking around the master cylinder lid while using a pressure bleeder? Might I just need a gasket?

kings1527
07-22-2013, 12:23 AM
I just bled my brakes the other day but I picked this up from Amazon instead of making my own:

http://www.amazon.com/Motive-Products-Power-Bleeder-European-/dp/B000Q6SL2W/ref=sr_1_3?s=automotive&ie=UTF8&qid=1374462013&sr=1-3

It worked perfectly and there was no leakage or spill. I figured it'd be a little easier to do it this way rather than hunt down all the parts. Time was a little more important in this case. The Motive bleeder is real high quality and should last. I believe the connection is the same for the brake fluid reservoir and clutch reservoir, too.

It worked great; my brakes felt exactly the same after replacing the fluid. The Motive is a tight system.

DMCMW Dave
07-22-2013, 12:57 AM
Any secret to keeping fluid from leaking around the master cylinder lid while using a pressure bleeder? Might I just need a gasket?

I big fat rubber o-ring the size of that cap.

Mark D
07-23-2013, 12:14 PM
Yeah the HELP brand cap should have come with a seal that fits into the cap. I had to cut the center of the seal out to clear the brass fittings I screwed onto the cap. A big o-ring would work too.

There is also a tiny hole in the HELP cap that allows air to vent in and out as the fluid level changes. I plugged it with a little screw.

Jonathan
11-24-2013, 01:15 PM
I have recently rebuilt my front brakes with new pads, hardware kit, pistons, bore seal, dust shield and shield clips. I reused the original calipers after cleaning them thoroughly (as well as the bolts holding them together).

I have both fronts all back together and ready to be bled. I did not touch anything on the rear brakes throughout the front rebuild. I also kept a close eye on the reservoir and it never fell more than a millimeter or two and to my knowledge, and never exposed the master cylinder below to any air. I used the suggestion to wrap a latex glove/rubber band around the end of the open brake line while the caliper was removed and that worked pretty well. I don't think very much leaked out below based on what I saw in the catch pan I had underneath there.

I have what I believe I will need to bleed the fronts myself and manually using the brake pedal. I have some clear tubing, a bottle to place the end of the tubing in and submerged with extra DOT4 brake fluid.

My question is: is there a requirement for the car to be on with engine running in order to adequately bleed the brakes? I ask this not because of the electrical or the reservoir sensor or something, but to do with the vacuum system and brake booster. If the engine is not on and there is no vacuum, then the brake booster isn't in effect. I was wondering if this in any way affects how effective the brake bleeding is?

My car has the front in the air still and has not been started in about one month. I could start it as is if necessary, but would prefer to get the wheels back on and off the jack stands before I do that.

David T
11-24-2013, 02:44 PM
I have recently rebuilt my front brakes with new pads, hardware kit, pistons, bore seal, dust shield and shield clips. I reused the original calipers after cleaning them thoroughly (as well as the bolts holding them together).

I have both fronts all back together and ready to be bled. I did not touch anything on the rear brakes throughout the front rebuild. I also kept a close eye on the reservoir and it never fell more than a millimeter or two and to my knowledge, and never exposed the master cylinder below to any air. I used the suggestion to wrap a latex glove/rubber band around the end of the open brake line while the caliper was removed and that worked pretty well. I don't think very much leaked out below based on what I saw in the catch pan I had underneath there.

I have what I believe I will need to bleed the fronts myself and manually using the brake pedal. I have some clear tubing, a bottle to place the end of the tubing in and submerged with extra DOT4 brake fluid.

My question is: is there a requirement for the car to be on with engine running in order to adequately bleed the brakes? I ask this not because of the electrical or the reservoir sensor or something, but to do with the vacuum system and brake booster. If the engine is not on and there is no vacuum, then the brake booster isn't in effect. I was wondering if this in any way affects how effective the brake bleeding is?

My car has the front in the air still and has not been started in about one month. I could start it as is if necessary, but would prefer to get the wheels back on and off the jack stands before I do that.

The motor doesn't need to be running. The pedal is just a little harder but not all that much. If you find it necessssary you can use both feet. You should bleed all 4 calipers enough to flush all of the old fluid out. Takes about 4 of those little bottles. Figure another one for the clutch. Get a "One Man Brake Bleeder". It is inexpensive. It is 2 pieces of tubing and a plastic check valve. You can do it yourself but just keep checking the reservoir so you NEVER let it get so low as to draw in air during the procedure. If you do you must start all over again from the beginning. If the pedal is spongy or soft when you are done it means you still have air in the system and you must do it again till you have ALL of the air out.

Jonathan
11-24-2013, 06:52 PM
...With the car on, when I push the brakes they go almost to the floor, and it's not too terribly hard to press down.

If I pump the brake very quickly, it becomes hard as a rock instantly. If I let off the brake for a few seconds then push again though, it feels softer again and goes to the floor.

With the car off, after pumping them a few times (like the manual says in the bleeding procedures), they feel pretty hard.

Is this a sign that there is just some air in the lines still somewhere I need to bleed out? Hoping so!


The motor doesn't need to be running. The pedal is just a little harder but not all that much. If you find it necessssary you can use both feet.

Thanks for the reply David. I was just about to write something along the lines of "yea, I figured as much, but I wasn't sure what was going on inside the brake booster." Well, never hurts to keep learning and I stumbled upon this great video explaining the vacuum assisted braking principle. It might explain part of what the OP mentioned too.


http://www.youtube.com/watch?v=LThrL8Jjsgc

Seems to make more sense now. Cheers!