View Full Version : Electrical Headlamp switch on the way out?
Dangermouse
06-03-2013, 01:32 PM
What is the correct operation of the headlight push-switch? I thought I knew, but now I am not so sure and before I start ripping things apart, I thought I’d ask.
Based on the schematic, the first push of the button, the orange side lights, side markers and tail lights should illuminate, but none of the 4 headlights.
The second push of the button should illuminate one filament of the outer headlamps. (aka dipped beams)
The column stalk switch would illuminate the second filament of the outer headlamps, plus the single filament of the inners (aka main beams or “brights” )
However, parked behind another car this morning, I noticed that the first push illuminated both the orange side lights and (presumably) one filament of the outers. I don’t recall if it has always done this or not. The second push made the illumination of the outers a little brighter, perhaps 20%. Obviously I have no way of quantifiably measuring this but it went from “bright” to “brighter”, rather than from “dim” to “bright”
Wrong per the schematic, but is this normal nonetheless?
Based on the schematic, the first push of the button, the orange side lights, side markers and tail lights should illuminate, but none of the 4 headlights.
The second push of the button should illuminate one filament of the outer headlamps. (aka dipped beams)
The column stalk switch would illuminate the second filament of the outer headlamps, plus the single filament of the inners (aka main beams or “brights” )
That's how it normally works. First push is parking/sidemarker/taillamps only, plus instrument lamps. Second push is those same plus lowbeam headlamps.
WelmoedJ
06-03-2013, 01:57 PM
That's how it normally works. First push is parking/sidemarker/taillamps only, plus instrument lamps. Second push is those same plus lowbeam headlamps.
Don't forget the first push also activates the amber front lights (they are part of the parking lights/city lights, whatever they are called in various countries).
Dangermouse
06-03-2013, 02:08 PM
I think we are all saying the same thing: amber front lights = orange side lights = front parking lights
WelmoedJ
06-03-2013, 03:16 PM
I think we are all saying the same thing: amber front lights = orange side lights = front parking lights
I only made this remark because to me "side lights" are side lights, e.g. sidemarker lights.
It's like with computers a zero is a zero, not a one.
Consequently front is not side.
Not to flame, only to be sure it's not misunderstood :)
Dangermouse
06-03-2013, 03:46 PM
Not to flame, only to be sure it's not misunderstood :)
No burnt bottom over here Welmoed. :) Different folks have different terms for the same thing.
Anyway, back to my oddly acting headlights......................
Jonathan
06-03-2013, 06:00 PM
No push = no lights
One push = all four marker lights (the ones on the sides of the vehicle, fronts being orange/amber, rears being red... mine with nice new gaskets!), plus the middle tail light bulb on each lens (bulb 3 of 5 if you will), plus the orange/amber lights on the front of the car (which remain steady on even though these are also your directional/turn signal lights).
Second push = all four marker lights remain on, middle tail light bulb on each lens stays on, low beam head lights come on (outer pair), orange/amber front lights (i.e. directionals/turn signals) stay on.
Third push = no push (return to step 1)
When the headlights are on, I can pull back on the stalk to turn on the high beams (inner lights plus outer high filaments). You have to hold it there as it won't stay on its own. If you click it forward, the same high beams come on, but they stay on until you click the stalk back.
Turn signals are also functional with headlights on, and alternate on/off in sequence the front amber/orange light on the corresponding side as well the rear tail light orange bulb (bulb 1 of 5 if you will).
Pressing the hazard switch also does similar to the turn signals, however both sides and all four orange/amber lights come on in sequence.
Most of this we know, but a couple other observations seemed a bit odd to me just now...
I can turn on the headlights as mentioned above with one push or two with or without the key turned in the ignition. I can also use the hazard switch regardless of the key in the ignition.
My flashing of the high beams seems to work with no key and no head lights, but pushing it forward to click into position does nothing.
Also, with no key in the ignition, my turn signals/directionals do not work. They will come on as hazards all together, but not on one side or the other as a signal, not unless you have the key in and turned to on.
My horns work anytime you want them to, however.
I have the new and improved head light switch, but do not have the orange wire connected which I think was intended on being the timer function that never quite worked (?).
I don't know how much of this is normal, or just part of the obligatory uniqueness of 3937... kind of like some fancy wallpaper under the centre console on some cars :)
Dangermouse
06-04-2013, 09:59 AM
Sounds like yours operates just like the schematic says it should.
Bugger for me then :(
After I typed this up, I got wondering if I was seeing the second filament in the outers light up early, so I checked again, and my outers have three levels of brightness
1. First push of the headlamp switch - OK brightness.
2. Second push of the headlamp switch - 20% brighter
3. Subsequent push-away of the steering column stalk into the "brights" position - distinct second filament illuminating.
Frankly I am in two minds as to whether to do anything about this. I am OK with the operation of the lights as I would typical turn on the headlights in low visibility but never just run with the side lights on. It is either a PO wiring mod or a faulty switch (or maybe a different type of switch).
Does anyone know if this is a typical failure mode? Will I be traveling at night and find that all my lights just go out?
WelmoedJ
06-04-2013, 11:41 AM
Sounds like yours operates just like the schematic says it should.
Bugger for me then :(
After I typed this up, I got wondering if I was seeing the second filament in the outers light up early, so I checked again, and my outers have three levels of brightness
1. First push of the headlamp switch - OK brightness.
2. Second push of the headlamp switch - 20% brighter
3. Subsequent push-away of the steering column stalk into the "brights" position - distinct second filament illuminating.
Frankly I am in two minds as to whether to do anything about this. I am OK with the operation of the lights as I would typical turn on the headlights in low visibility but never just run with the side lights on. It is either a PO wiring mod or a faulty switch (or maybe a different type of switch).
Does anyone know if this is a typical failure mode? Will I be traveling at night and find that all my lights just go out?
The original light switch configuration has the main light power running through the switch.
The current may eventually destroy the switch's function.
Toby has circumvented this issue using a relay (chaning the switch's wiring a bit) so the main power does no longer run through the switch.
If your car still has the original wiring configuration, it may have caused your switch to malfunction.
Check if there's a relay connected to this head light switch.
Other malfunctioning issues may be found in bad contacts inside the switch (ageing or carbon build-up as a result of may pushes).
You could check the "normal" functioning of the head lights by unplugging the switch and jumpering the connections in the (wire-side) socket.
Use the diagram and wire colours to determine which wire to connect to power.
It could also be that some of the connections inside the switch do not properly connect on the various push positions.
Dismount the switch and check the switch itself using a universal meter.
Hope this helps.
Farrar
06-04-2013, 01:04 PM
I would typical turn on the headlights in low visibility but never just run with the side lights on.
If that's the case, you can replace your headlight switch with a hazard switch.
Jonathan,
Sounds like ya need to fix your license plate lights.:tongue2:
=======
The original light switch configuration has the main light power running through the switch.
Actually, the High and Low beams each have their own relay (#100 & #101 in the WS Manual schematic) fed straight off of the battery (unfused) and then fused on the way to the headlamps. The only power running through the switch for them is the trigger signal, which is so small that is isn't worth worrying about.
========
Frankly I am in two minds as to whether to do anything about this. I am OK with the operation of the lights as I would typical turn on the headlights in low visibility but never just run with the side lights on. It is either a PO wiring mod or a faulty switch (or maybe a different type of switch).
Does anyone know if this is a typical failure mode? Will I be traveling at night and find that all my lights just go out?
I could see it acting the way it does if the switch was bad (short between high and low section), except there wouldn't be any change in low beam brilliance (push 1 to 2) since the relay doesn't use the switch power to feed the bulbs... (Make sense?)
I'd check out the switch as Welmoed suggested...Same for the wiring etc at the relay(s) (pull em both and see what happens when you jump power to the bulb feed wire(s)....
Dangermouse
06-04-2013, 03:40 PM
I could see it acting the way it does if the switch was bad (short between high and low section), except there wouldn't be any change in low beam brilliance (push 1 to 2) since the relay doesn't use the switch power to feed the bulbs... (Make sense?)
I'd check out the switch as Welmoed suggested...Same for the wiring etc at the relay(s) (pull em both and see what happens when you jump power to the bulb feed wire(s)....
I'll definitely be tracing out the circuit, but if this was a typical failure mode, I would just order a new switch and be done with it.
If I didn't know for a fact that my car has never left Atlanta, I would say that the wiring has been altered to give DRLs. :confused2:
I'll report back with what I find.
Dangermouse
06-05-2013, 05:41 PM
Some interesting progress today. Good news then bad news then good news again.
Good News: Took the switch out and tested it and it seems to be operating as intended. No signs of melting.
http://dmctalk.org/attachment.php?attachmentid=19570&d=1370464285
I particularly looked at the contact for the blue (U) wire (upper front in the photo) that goes to the two relays, via the stalk switch. There was a little oxidation on the contact, but 12V from the Blue/Brown connector is only switched to it when the switch is in the second position, not the first, so 12V is not getting to the lights from the switch. Did a continuity test at the connector and the blue (U) and red/green (RG) are definitely joined somewhere.
Bad news: Looked at the relays as suggested. Pulled low beam relay but couldn’t pick up 12V anywhere on the base. Odd.
Odder yet, was the fact that I could turn on the low beams with the relay still in my hand :headscratch:
Good news: Literally 15 minutes later I get an email from a DeLorean owner that I am not sure I have even met (and isn’t even a member here) who had read this thread and suggested that indeed I may well have DRLs (thanks Ray), a theory later confirmed by DMCSEan. Byrne H did a lot of work on my car a decade ago and apparently this was an upgrade he offered on a couple of cars. I still have all the receipts and a quick check shows an entry for “Wiring lights to ignition (safety lights)” which isn’t completely accurate but at least points me in a direction.
If I didn't know for a fact that my car has never left Atlanta, I would say that the wiring has been altered to give DRLs. :confused2:
So in answer to my own question, apparently so. Or at least partially so.
All that remains is to work out how he did it (contacts in the assessory relay are involved, I'm told) and then update my schematic.
Szabi
10-04-2014, 01:39 PM
I built in the new headlight switch set (108388N), ordered from Delorean Europe.
31026
Everything was done according to the enclosed assembly instructions, but the switch is not working. When pushing the button, a click can be heard from the `brick` panel that came with the set, but that`s all. When pushing for longer time (cca. 1 sec) and releasing the button, there is an additional click from the relay of the A/C illumination panel (NOT from the dip beam relay), and the side lights on the car flash shortly. Is there anything I could try or check? I am sure the wires were connected the same way as shown on pictures of the assembly instruction.
(Just to be sure, I re-connected the old switch now and the headlights work properly).
I built in the new headlight switch set (108388N), ordered from Delorean Europe.
31026
Everything was done according to the enclosed assembly instructions, but the switch is not working. When pushing the button, a click can be heard from the `brick` panel that came with the set, but that`s all. When pushing for longer time (cca. 1 sec) and releasing the button, there is an additional click from the relay of the A/C illumination panel (NOT from the dip beam relay), and the side lights on the car flash shortly. Is there anything I could try or check? I am sure the wires were connected the same way as shown on pictures of the assembly instruction.
(Just to be sure, I re-connected the old switch now and the headlights work properly).Did you try contacting DeLorean Europe where you bought it from? They do customer support too :fancy:
Szabi
10-06-2014, 04:10 AM
Did you try contacting DeLorean Europe where you bought it from? They do customer support too :fancy:
Yes, I immediately contacted Ed, no answer yet.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.