Log in

View Full Version : Electrical No power from key to start inhibit relay



jangell
06-03-2013, 07:27 PM
I just took my car out for a quick drive. On the way home I stopped at my mailbox, turned the car off and grabbed my mail. When I got back in and turned the key, the starter wouldn't even turn over. Everything else electrical seemed to work, though; it was just the starter.

Some quick research with a Power Probe (which I keep in my car for just such a situation) found that no power is getting from the key to the start inhibit relay (red/white wire). If I manually provide 12v to the starter via the relay socket (the other red/white wire) while the key is in the "run" position, it starts right up. I also tested the relay and it's fine, so that's not it. For whatever reason, it seems that no power is making its way from the key to the socket.

The socket appears to be fine, and the wire appears to be connected to it, but I didn't fish around too much in there yet. I was wondering if anyone had any tips on dismantling enough of the steering column to get to the key switch so that I could check the circuit at that point. I'm comfortable enough in the relay compartment, but I haven't had to deal with anything of the electronics at the steering wheel yet.

Thanks!

-- Joe

Elvis
06-03-2013, 07:40 PM
There's nothing to be afraid of.

just do it.


Do you have the schematic ?

jangell
06-03-2013, 07:43 PM
There's nothing to be afraid of.

just do it.

Do you have the schematic ?

Yup, I have all the nice color-coded ones. It was actually taking the steering column housing apart to get access to the wiring that I was wondering about, more than the wiring. I probably overlooked it in the workshop manual.

-- Joe

Bitsyncmaster
06-03-2013, 08:43 PM
Don't forget to check the ground wire on the relay socket. That just requires an ohmmeter from the pin to the common ground juntion.

Farrar
06-03-2013, 09:16 PM
Is it a manual or an auto? If it's an auto, the neutral safety switch could be the culprit.

DMCMW Dave
06-03-2013, 09:56 PM
Try starting in neutral

jangell
06-04-2013, 10:08 AM
The car is auto. I tried starting in both Park and Neutral, but no go. I also tested the yellow/white wire from the switch to the relay and confirmed that it is tied to ground while in park, so that's good. Ground is good too.

-- Joe

jangell
06-04-2013, 10:14 AM
Well, this is embarrassing: Years ago I installed a DeLorean Parts NW remote starter, remote door lock module, remote door opener and kill switch. Due to overly-aggressive door seals, I have been unable to use the door opener (it pulls the latches, but the doors are stuck to the seals by friction). I never actually use the remote starter because of how loud the car, and I don't want to annoy my neighbors, and I rarely lock my doors due to some old problems with the lock sticking on the passenger's door.

The kill switch is rigged to the lock module -- lock the doors with the remote, and the kill switch engages. Apparently I accidentally hit the lock button when I was getting the mail (but for some reason the doors didn't lock; I'll have to look into that). The kill switch's relay is wired between the key and the start inhibit relay socket.

The fix was trivial: Hit the unlock button on the remote. The car started right up.

Worse is this isn't the first time I've done this -- once I locked the doors with the remote and later unlocked them with the key, which meant the starter kill was still in effect. I shorted the starter to get it home and was on the phone with DMC CA for about 15 minutes before I figured out what I'd done.

Thanks everyone for taking the time the help!

-- Joe

Farrar
06-04-2013, 12:43 PM
Glad it was an easy fix! :)