Log in

View Full Version : General Washing the car?



Hokie
06-07-2013, 06:06 PM
OK, so this may seem like a stupid question to some, but I'm seriously interested in some advice on washing my D. I'm very hesitant to just whip out the bucket and suds and go at it. Are there areas to avoid directly spaying so as to not get water inside the car? Any advice on how the keep the engine dry or whether or not that is even important? Any other thoughts on keeping a D clean? Thanks.

dmc6960
06-07-2013, 06:16 PM
Well, it's is a car. Don't be afraid to get it wet. Generally a garden hose and bucket will not give you any issues. Any wiping with a cloth or sponge should go with the grain. Avoid spraying water directly at the engine, but simply getting wet will not hurt it. Don't put much pressure on the hood when washing or drying. It may help to open it up if drying by hand, better access. You may find a few minor leaks in the door weather seals but they generally won't be horrible. If you use Windex do NOT get it on any black portion of the car.

There's a start.

jawn101
06-07-2013, 06:17 PM
OK, so this may seem like a stupid question to some, but I'm seriously interested in some advice on washing my D. I'm very hesitant to just whip out the bucket and suds and go at it. Are there areas to avoid directly spaying so as to not get water inside the car? Any advice on how the keep the engine dry or whether or not that is even important? Any other thoughts on keeping a D clean? Thanks.

This is a question that's as up to personal preference as synthetic vs conventional oil, what brand of tires to go with, etc. Do what you're comfortable with. There is a pretty good general consensus that automated car washes are not right for us due to the fragility of the louvers and the unpredictable effects high-pressure water can have on our less than watertight bodies.

Me, personally? I use one of those Mr. Clean AutoDry hose nozzle attachments, hooked to the hose output on my water softener (the water where I live is *ridiculously* hard). I fill up a bucket with clear water and some Ivory dish soap. Hose the car down with plain softened water. Switch the AutoDry to soap mode and spray down again. Use a bone sponge with a scrubby back and some of that water/Ivory mix to get off any stubborn spots, bugs, etc. Hose it down again with fresh water. Switch to the deionize mode to get a spot-free rinse. Dry it with a PVA drying sheet and microfiber towels.

Areas I stay away from: I try not to use high-pressure water near the roof seals or the side louvers, as I don't want to force water past and into the body.

Depending on how dirty the car is and how deep I want to clean, I will spray down all the exposed fiberglass areas (louvers, engine cover, pontoons, wheel wells, etc) with Kaboom foaming cleaner before starting the above process. Regular spray-on wheel cleaner for the wheels. I don't dress the tires as I hate how they look shiny. I don't use any after-wash polish or wax on anything, be it steel, paint or fiberglass.

You don't have to worry about getting the motor wet, as long as your plug boots are the correct type and are on tight. You do want to avoid soaking the ignition coil or the distributor. If you just wash the car with the lower engine cover closed all those concerns should really be handled for you, it does a good job of keeping water off the critical components.

Another thing I recently discovered I should be doing: if you are washing the car on an incline, do it so the nose is at the lowest point. This will help make sure the windshield air intake drains water outside the car rather than inside the evaporator box. That drain is kind of poorly designed and can become clogged easily.

Nicholas R
06-07-2013, 06:32 PM
Mr. cleans magic erasers. I swear by them. That plus dawn dish soap, turtle wax tire stuff for the wheels, an occasional pressure washing of the rims, and a chamois to dry it all off with.

Rich
06-07-2013, 06:43 PM
There's another way to go, one that suits this car pretty well.

To correctly remove dirt from a painted car you want plenty of water and soap so as not to let the dirt scratch the paint. But with a brushed-stainless car that's less of a problem. Or no problem, at least on the glass and the stainless.

Try a bucket o suds (car suds, NOT dish detergent) and a wash mitt along with a clean "rinse" towel wetted with clean water. And with no wet- or rinse-hose.

With the car in the shade give the car a suds-only scrub, doing a section at a time and wiping with the grain as others have mentioned. Unless the car is filthy you don't need much soapiness.

Then before that section starts to dry go over it with the wet towel as a "rinse", followed by a dry towel or chamois. Then work it section by section in about 4-5 sections. That's it. Treat the glass any way you like.

No hose, no puddles, no leaks, nothing into the engine bay. Be sure to go light on the front and rear (painted) fascias so as not to cause any tiny scratches there with this method. Or just wash them using a hose.

It's a bit unorthodox but it works.

As an aside, this car is remarkably easy to keep clean in that a clean wet cloth can take care of dust and minor dirt on the stainless. No need for a whole wash job most of the time. Just stay on top of it with the minor wipe-downs.

Tillsy
06-07-2013, 10:08 PM
Likewise I don't use a hose, I don't even take her out of the garage.

Just a bucket of water, rinse a sponge in it, squeeze it almost dry, then wipe along the grain on one spot and in same direction three times. Repeat the rinse, squeeze, and wipe until I've done all the stainless panels on one side. I then rinse the bucket and start again for the other side, then do it again for the facias. No need to chamois her down as she's already dry and spotless on each of the third wipes.

Clean in 20 minutes flat, no mess, and looks great.

If she's absolutely filthy, or once a month or two, I'll first do all the stainless panels with the same process but some dishwashing liquid in the water - not the facias though. I then redo the above normal process with plain water to get it all off.

That thorough clean is about an hour of work instead of 20 minutes. I then use Windex on the glass and tyre shine on the tyres.

My process takes full advantage of the fact that the panels are all brushed stainless. Doing this on my other cars would scratch them up - they are still the old fashioned hours worth of hosing, washing, rinsing, chamois, wax, blah blah blah...

DMCMW Dave
06-08-2013, 03:06 PM
If you are really going at it with a hose, open the engine cover first and cover the engine with a large plastic trash bag or something similar that will run the water off to the sides of the engine. This will keep you from accidently flooding the valley and/or spark plugs. A strong hose is a LOT more water in there than rain coming through the louvers. BTW, this is not a bad idea if parking the car outdoors for extended periods.

DMC5180
06-08-2013, 10:57 PM
When I first got my car, I never washed it and just used Stainless cleaner/polish per D1 recommendations. Problem is it looks great at first then starts turning dark and collects dust/dirt like mad. I quit using that stuff years ago and switched to Manual car washing. I like the foaming brush. I've also never had an issue Flash spraying the engine enough to knock the dust off. I generally use the full range spray modes except WAX but including spot free rinse. When I'm done I give it a quick towel dry then hop in and go for a 10 mile drive at highway speed to blow dry the rest The heat from the engine quickly dries out the engine and compartment.

Lately, I've switched to washing it in the driveway with a bucket of hot water and (car washing soap) and a wash mitt.

Jacko
06-08-2013, 11:45 PM
Lately, I've switched to washing it in the driveway with a bucket of hot water and (car washing soap) and a wash mitt.

That's what I do. I even use car soap with wax in it ... doesn't do any good but it doesn't hurt as far as I know.
Also, I have a California Duster that I use between washes.:smile:

WelmoedJ
06-09-2013, 06:23 AM
If you are really going at it with a hose, open the engine cover first and cover the engine with a large plastic trash bag or something similar that will run the water off to the sides of the engine. This will keep you from accidently flooding the valley and/or spark plugs. A strong hose is a LOT more water in there than rain coming through the louvers. BTW, this is not a bad idea if parking the car outdoors for extended periods.

If covering your engine with something to prevent it getting flooded while parking outside it may be a good idea to hang a reminder on your key or steering wheel.
This way you can avoid more damage than heavy rain can do (except in flooded areas like in Europe now :( ).

BTW, every now-and-then when I'm lazy, I drive my car through a carwash.
No special precautions taken; this hasn't hurt either car or engine in the five years I now own it.
Intake manifold has taken been off 2 during those years (other reasons) and I didn't find anything pointing to water having been in there too long.

I guess it all boils down to regular pre-emptive maintenance, keeping you car in good shape.
The car is not made of sugar, so water couldn't really hurt or damage it.
Neglect to keep it in good condition however hurts it more than water.

Jonathan
06-09-2013, 09:43 AM
I didn't see Bar Keepers Friend mentioned anywhere? For Hokie, BKF is sort of like "Comet" that you might use to clean your kitchen sink. It is not quite as abrasive though. You can get a powder or a liquid. If find it does a nice job on bringing back the shine of the stainless and getting some of the dirt out of the grain.

There are other thread's written here about it, but basically:

- Rinse car down with water. You can even wash it first if you like with soap and water depending on how dirty it is with mud or dust or whatever.
- Once cleaned the "typical car wash way" focus on one section of stainless at a time. Say one of the quarter panels. Get that panel wet with plain old water.
- Using a scrub pad of some kind (Scotch Brite for example or something else plastic, but definitely NOT steel wool), put a little BKF powder on the scrub pad.
- Then while you go WITH THE GRAIN, scrub it in short, straight movements. You can over the same spot a couple times. No need to rush. Reapply more powder as you see fit.
- Once you have a small area scrubbed clean, rinse the area off. The reason you try to do a small area at a time and keep rinsing it off frequently is because the little residue from the powder can get everywhere and look crummy on the black parts of the car.
- Basically do all the stainless on the car this way. Once finished, rinse it all off again, soap and water again if you feel like it.
- The BKF cleaning is more of a once or twice a season wash for me as it tends to take time. It does really make a noticeable difference though.

I like Tillsy's idea about using a sponge and bucket in your garage, I'm going to try that. And will be grabbing a Mr Clean Magic Eraser out of the kitchen cupboard to give that a test whirl too!

Ryan S.
06-09-2013, 11:19 AM
I also do Tilsy's sponge bath method in my garage with dish washing soap once or twice a week. I drive mine almost daily now. I have used Windex but it didn't really work for me. I finish it with stainless steel cleaner/polisher spray to give it a nice shine. For complete cleaning, I have used bar keeper. But I am going to try magic eraser. I think that might work. I don't like cocaine like residues after bar keeper cleaning.

JIMJAM
06-09-2013, 12:16 PM
This vid shows the way I do it. For about A dollar you can get the interior,carpet,dash,headliners all in under 2 minutes.

https://www.youtube.com/watch?v=oMVSXi2JgpY

DMC5180
06-09-2013, 01:23 PM
That's what I do. I even use car soap with wax in it ... doesn't do any good but it doesn't hurt as far as I know.
Also, I have a California Duster that I use between washes.:smile:

LOL, I forgot about my California Duster. Actually THAT is what I used early on between SS Cleaner treatments. Now I use it between washes. I never leave home in the Delorean without it. I keep mine in the The JACK STORAGE COMPARTMENT.

19750 19751

kobachi
06-09-2013, 05:41 PM
If you use Windex do NOT get it on any black portion of the car.

Crap, I definitely got windex on ...most of my black portions recently. What's the damage?

Jacko
06-09-2013, 06:15 PM
[QUOTE=DMC5180;107134]LOL, I forgot about my California Duster. Actually THAT is what I used early on between SS Cleaner treatments. Now I use it between washes. I never leave home in the Delorean without it. I keep mine in the The JACK STORAGE COMPARTMENT.

The California Duster really does the trick on my Black Jaguar. Dennis, how does one clean the duster? Seems like I recall the instructions say don't wash it.

DMC5180
06-09-2013, 06:22 PM
[QUOTE=DMC5180;107134]LOL, I forgot about my California Duster. Actually THAT is what I used early on between SS Cleaner treatments. Now I use it between washes. I never leave home in the Delorean without it. I keep mine in the The JACK STORAGE COMPARTMENT.

The California Duster really does the trick on my Black Jaguar. Dennis, how does one clean the duster? Seems like I recall the instructions say don't wash it.

That is correct, you don't. I haven't washed mine in 19 years and don't plan too. It has some kind of oil it that holds the dirt. If you were to wash it. you would loose the oil. They even say it works better and better the dirtier it gets.

dmc6960
06-09-2013, 10:50 PM
Crap, I definitely got windex on ...most of my black portions recently. What's the damage?

May turn them blue in the short run, fade them generally in the long run.

Farrar
06-10-2013, 05:42 PM
I use Windex on the stainless, wiping with the grain with successive papertowels until the papertowel comes off the surface clean. Then I let it dry, and apply Lemon Pledge to the stainless -- helps mitigate fingerprints and makes the garage smell nice. 8)

As for the black parts... :shrug:

Jacko
06-10-2013, 08:37 PM
Crap, I definitely got windex on ...most of my black portions recently. What's the damage?

I've always used Armor All on the black parts (louvre, engine cover, mirrors, everything black)
and I always get a little on the stainless. To clean this up I spray on a little Windex and wipe it
down with paper towels. I've not had any issues with the black parts turning brown.

jawn101
06-10-2013, 09:16 PM
Really interesting, the different perspectives on this. I knew it was personal but it seems like we're all over the map!

SS Spoiler
06-10-2013, 09:20 PM
Get some of that cleaner/sealer made just for the black trim on your car. Several brands out there at auto parts stores. Armor All tends to leave streaks running down the SS in rain.

Dangermouse
06-10-2013, 09:21 PM
Yes, it's funny that most people are all anti-Armor All and then Jack appears and recommends it and suddenly I am reconsidering it. He's done more miles than all of us combined so any advice on upkeep is golden.

Jacko
06-10-2013, 10:55 PM
Yes, it's funny that most people are all anti-Armor All and then Jack appears and recommends it and suddenly I am reconsidering it. He's done more miles than all of us combined so any advice on upkeep is golden.

You tell 'em, 'Mouse 8):strongman:

Tillsy
06-11-2013, 05:01 AM
I don't get the anti-AmorAll thing either, never heard it until I came to is forum, but I'm a big fan of it. Have always used it on my cars religiously since new and years later they are in absolute fantastic condition, so happily use it on my DeLorean without issue.

thirdmanj
06-11-2013, 09:12 AM
Ever since I got into cars, I've been told to steer clear of Armorall. Not because it damages the interior, but because it evaporates an leaves an oily residue on the windscreen.

Guitarman on this Lexus forum seems to have a pretty good idea on this "anti Armorall" thing.
http://www.clublexus.com/forums/automotive-care-and-detailing/529486-whats-wrong-with-armorall.html

Dangermouse
06-11-2013, 09:46 AM
Personally I hate the super-shiny look traditional Armor-All gives (or what I assume is what used car salesmen use on their products) It has a slick, slippery feel that I really don't like. Having said that, I use the "matte finish" Armor-All products on modern plastics in my DD as they do give a nice finish. As I am not keeping them for 10 years, I'm not so concerned about any long term effects.

When I get my new dash, I will certainly consider it.

Farrar
06-11-2013, 10:44 AM
I once had to take my car out for a quick show-and-tell. I was behind schedule and didn't have time to go to the store to buy "Back to Black" or whatever, so I used black shoe polish on the black trim bits. It worked great, but of course the effect was only temporary. When I think about it, it was good to have on hand in a pinch, but given most folks' choice of footwear I doubt that a lot of people just happen to have a can of black shoe polish sitting around these days.

Jacko
06-11-2013, 11:14 AM
It's easy to understand why folks don't like Armor All ... if it's not applied correctly. Here's the drill I use:

I use the liquid in a bottle and have not tried the wipes. On the black part I'm working on I use a clean soaked
rag and apply liberally and give it a little time to 'soak in'. Then I use a clean, dry towel to do my best to rub it off.
If it's applied and not rubbed off it leaves a residue that is definitely undesirable. Further, if I'm doing a small area, the
little side vents or the air intakes or the little black circle around the keyhole it's practically impossible to apply the
Armor All without getting it on the SS. On these parts I spray Windex on the part and vigorously wipe it down until it's dry.
I use Armor All inside the car as well. However I don't use it on the dash; I don't put anything on the dash except wipe it down
with a water dampened towel. Why? Any kind of protectorant on the dash makes it reflective in the windshield making it
hard to see when the sun is right.

The next time you are in Autozone or Wal-Mart look how many brands of protectorant there are ... there are so many
because it's 'different strokes for different folks' ... select the one you like ... I'm sure it'll be ok.:wave:

mluder
06-12-2013, 05:12 AM
I have tried a bunch of different products.

In the end...

Wash with regular "car washing" detergent and warm water.
Dry thoroughly.
Then go over the entire car with SS Glow from the DMC vendor of choice. It works on the stainless as well as all the painted bits, fascias, louvers, and even the black plastic parts like the side vents.
I wide it on with a lint free cloth and then wipe the excess off with an old cotton diaper. The SS Glow is very oily so you have to keep wiping and turning the diaper until you get most of it off.

I have also used 303 Aerospace on the black parts but it takes multiple treatments and still doesn't richen the color on the bumpers, louvers, and side vents like the SS Glow does.

I also use the Bar Keeper's Friend before big shows, etc. Really makes the stainless glow.

Cheers
Steven

Judo land
06-15-2013, 12:10 AM
I am in the dairy industry and we have a lot of 304 stainless. I have tried everything to clean the stainless. A couple of days ago he told me he had several people use WD40. We tried it yesterday and it made the pipes look like new! Has anyone ever tried this on there cars?
Sent from my GT-I9100 using Tapatalk 2

Hokie
06-15-2013, 12:17 AM
I am in the dairy industry and we have a lot of 304 stainless. I have tried everything to clean the stainless. A couple of days ago he told me he had several people use WD40. We tried it yesterday and it made the pipes look like new! Has anyone ever tried this on there cars?
Sent from my GT-I9100 using Tapatalk 2

I don't know how many people use it on their cars but I can tell you that when I went to my local Lowes Home Improvement and asked the guy in the appliance section what he recommended, he said the only thing they use on their appliances is WD-40. I have yet to try it.

Rad Dad
06-15-2013, 12:58 AM
I realize that this subject has as many different supporters/haters as the "what kind of oil should I use". As a 30+ year owner of a DeLorean, here's my 2ยข worth.

There is a big difference in what you might want to use depending upon whether you drive your car essentially to car shows or the local coffee & cars vs. driving your car as a daily driver or a long distance tourer. I fall in the last category, but that doesn't mean that i haven't shown my car and won some awards with it.

I believe, and 30 years of ownership has proven it to me, that if you want your car to look good 90% of the time and in saying that I am assuming that it is out in the public to be viewed 90% of the time and not locked in a garage . . . . .don't use ANY product that has any petroleum based cleaner/polisher. I don't care whether it is from DMCH (I have no quarrel with James, Stephen, etc.) or is WD40, or . . . you name it. If there is any lubricant/petroleum in the product, vestiges of that will remain on the surface and WILL attract dust and fingerprints. So - - if you want to do something just before a "show and shine". . . .have at it. It will look quite nice for a short period of time. As long as the wind in not blowing dust or pollen and as long as kids don't come along with their parents and that all "have to touch it" . . . .your car will look great.

On the other hand, if you want your car to look very nice, but not necessarily ready for the concours, soap(actually, detergent of your choice), water, and/or glass cleaner will give you a very nice CLEAN look and will not have the dust/dirt gathering proclivities of the aforementioned products.

Now - FWIW (and that is probably not much) - I wash my car with whatever detergent (not "soap") is handy. After a quick toweling that removes most of the water, but not all, I quickly finish the metal panels with good old Windex and paper towels. I constantly receive "kudos" for how nice my car looks.

Oh, again FWIW - I have stainless steel appliances in my kitchen. Guess what . . . .a wash rag with detergent gets off any major spills, fingerprints, etc. and then a quick application of Windex wiped off with paper towels and if I could put wheels on the appliances, they could win awards at a DeLorean car show.

Do you think you hit one of my hot buttons? Yeah . . . . . .maybe!

Dick Ryan - The Rad Dad
Vin 16867

Dmcfan1981
06-16-2013, 03:35 AM
I've had good results with bar keepers friend and just regular dish detergent and water...no rocket science involved

JRNY13
06-16-2013, 11:30 AM
I've found that SS glow evaporates almost immediately and unevenly when applies to the bumpers.

David T
06-16-2013, 05:02 PM
I have to agree with rad dad. Soap and water is about the best thing with some quick touch-ups using Windex and paper towels to remove any bugs or fingerprints. For show duty the S/S Glow is OK but expensive. All of these things other than soap and water holds any dust that settles on the car. Black Again is good for the black parts like the rear sunshade, rub strip, and bumpers. Get some silicone spray, spray a little onto a paper towel and wipe down all of the rubber weatherstripping to clean it and keep it supple. Glass Plus for the glass (or Windex). A good UV tire protectant too. When washing the car you should use a car soap. it is milder than dishwashing liquid and washes off easier. I like using very hot water so it washes off the bugs and tree sap too. Look at Griot's Garage for a lot of good car detailing products.
David Teitelbaum

Mark D
06-17-2013, 11:34 AM
I use automotive car soap to clean the whole car and windex on the SS panels if anyone has left a greasy hand print. I don't really like any of the polishes or waxes for the stainless since it makes it look darker, attracts finger prints & dust, etc. I use a high quality carnuba wax on the painted fascias, Mothers back to black for the exposed black urethane on the bumpers and other black trim. I stay away from washing the car in dawn dish soap since it will strip all the wax of the painted parts. Automotive car soap is milder but still gets rid of dirt and water spots.

Usually the wheels get clean enough spraying down with a hose, but if brake dust starts to build up I use turtle wax wheel cleaner. For the interior I just use a damp cloth to wipe away dust and on the leather seating surfaces, shift boot, and steering wheel I occasionally use leatherique to keep the leather from drying out.

Between washes I use a california duster to wipe the car down. Once a year I'll use BKF to keep the stainless looking bright.

Hokie
05-01-2014, 03:20 PM
I used Bar Keepers Friend for the first time this week in preparation for an upcoming car show. I used the liquid. ABSOLUTELY AMAZING! I had NO idea how dirty my D was! I didn't even use a Scotch Brite or a sponge - I just used a wet towel. I've seen no downside whatsoever, meaning no residue. I guess that's the difference between the powder and the liquid? I highly recommend this product; it's like driving a totally different car! Next time I use it I'll use a Scotch Brite pad just to see if it makes the D even cleaner.

Silverbullet
05-01-2014, 04:42 PM
They also know at Bar Keepers Friend... Look and the 3rd post... http://www.barkeepersfriend.com/car-care

Craig

mluder
05-01-2014, 06:50 PM
I used Bar Keepers Friend for the first time this week in preparation for an upcoming car show. I used the liquid. ABSOLUTELY AMAZING! I had NO idea how dirty my D was! I didn't even use a Scotch Brite or a sponge - I just used a wet towel. I've seen no downside whatsoever, meaning no residue. I guess that's the difference between the powder and the liquid? I highly recommend this product; it's like driving a totally different car! Next time I use it I'll use a Scotch Brite pad just to see if it makes the D even cleaner.

+1 on this... Soap will get the car clean but the BKF makes the stainless glow. I use a cloth covered sponge I got at Auto Zone or other parts store. Then hose it all off thoroughly and wipe down with some beach towels.

If I decide to go the extra mile I will use the SS Glo from DMCH. I spray it on, Wipe it in with a terrycloth towel and then buff it out with a clean cotton diaper. Looks great but I agree, the petrol based don't attract dust - the car does that on its own - but they do HOLD dust that would normally just blow away.

Cheers
Steven

Michael
05-01-2014, 07:30 PM
+1 on this... Soap will get the car clean but the BKF makes the stainless glow. I use a cloth covered sponge I got at Auto Zone or other parts store. Then hose it all off thoroughly and wipe down with some beach towels.

If I decide to go the extra mile I will use the SS Glo from DMCH. I spray it on, Wipe it in with a terrycloth towel and then buff it out with a clean cotton diaper. Looks great but I agree, the petrol based don't attract dust - the car does that on its own - but they do HOLD dust that would normally just blow away.

Cheers
Steven

It's an illusion. Once the oxide layer re forms in a few days you are right back where you started from. BKF is great on old, neglected stainless, but if your stainless is already clean, it will only brighten it for a few days and your time is better spent elsewhere.

Lenny
05-02-2014, 02:17 AM
I do almost everything you do but one addition. I have a car wash down the street that I take it to. I used to wash it and do everything by hand. I got stuck in a downpour one day and had water in the car. So I took it through the car wash to see where the leak was. When I got out the detailers went nuts over the car. They used Luxol on the interior and something else on the "Black". when I got home there was nothing else to do. Now before every show I take it to the car wash there is one detailer that works his butt off on the car he works so hard I tip more that the cost of the car wash. I really like the wheel washer they use it is high pressure and it really does a good job.

I then use SS Glo once I get to the show and that's it. I do the bar keepers friend once a year.


I have tried a bunch of different products.

In the end...

Wash with regular "car washing" detergent and warm water.
Dry thoroughly.
Then go over the entire car with SS Glow from the DMC vendor of choice. It works on the stainless as well as all the painted bits, fascias, louvers, and even the black plastic parts like the side vents.
I wide it on with a lint free cloth and then wipe the excess off with an old cotton diaper. The SS Glow is very oily so you have to keep wiping and turning the diaper until you get most of it off.

I have also used 303 Aerospace on the black parts but it takes multiple treatments and still doesn't richen the color on the bumpers, louvers, and side vents like the SS Glow does.

I also use the Bar Keeper's Friend before big shows, etc. Really makes the stainless glow.

Cheers
Steven

Jonathan
05-03-2014, 07:58 AM
I used Bar Keepers Friend for the first time this week in preparation for an upcoming car show. I used the liquid. ABSOLUTELY AMAZING! I had NO idea how dirty my D was! I didn't even use a Scotch Brite or a sponge - I just used a wet towel. I've seen no downside whatsoever, meaning no residue. I guess that's the difference between the powder and the liquid? I highly recommend this product; it's like driving a totally different car! Next time I use it I'll use a Scotch Brite pad just to see if it makes the D even cleaner.

What method do you use with the liquid?

I had always used the powder and it would go something like: wet/rinse entire car; then one panel or area at a time, get stainless wet, and with a scrub pad use a little bit of powder and go up and back with the grain while applying moderate pressure; rinse as required and keep panel wet as required; when finished panel, rinse it off and do the same for the rest of the car; then give it a final rinse or wash for any remaining residue.

The residue is the main deterrent with the powder form and the only downside I usually see.

DMCMW Dave
05-03-2014, 09:39 AM
What method do you use with the liquid?

I had always used the powder and it would go something like: wet/rinse entire car; then one panel or area at a time, get stainless wet, and with a scrub pad use a little bit of powder and go up and back with the grain while applying moderate pressure; rinse as required and keep panel wet as required; when finished panel, rinse it off and do the same for the rest of the car; then give it a final rinse or wash for any remaining residue.

The residue is the main deterrent with the powder form and the only downside I usually see.

They each have their purpose. The liquid is much less messy and does not end up in all the crevices around the doors and trunk. The powder is a bit more aggressive in the cleaning action.

SIMid
05-06-2014, 08:27 PM
The powder is a bit more aggressive in the cleaning action.

I have noticed with the powder (BKF), if you do not rinse and dry the panel quickly, it will leave water stains.

I try not to wash mine unless it was necessary, so to give her a quick once over with a MicroFibre Cloth using;

http://www.meguiars.com.au/products/car-care/paint-care/wash-maintain/ultimate-quik-detailer/

Better than windex and smells great after use. A little more expensive though, but having used many surface products, this I found to be the best.

Jacko
05-07-2014, 11:22 AM
I may have missed it but I didn't see this technique mentioned. After the final rinse with water
I take the car to a nearby rural road with a straight stretch and air it out. A few minutes
at eighty (or 88 if you prefer) mph will pretty much dry the car.:wave2:

Victor
05-09-2014, 02:45 PM
I simply use warm water and Vim in a cream form, for the Stainless steel.

Cheers!

nkemp
05-09-2014, 03:34 PM
The other day I washed it with window cleaner and was not pleased with the results. So I put some vinegar in warm water and washed it again. I simply soaked the rag, washed the area and used a towel to dry. I am very pleased with the results. I think the slightly acidic nature of vinegar removes the light grey corrosion that SS will develop. As such, I got a nice bright finish as a result.

ccurzio
05-09-2014, 03:42 PM
The other day I washed it with window cleaner and was not pleased with the results.

BE CAREFUL WITH THIS.

Windex (or a knock-off) is fine for the stainless, but if you manage to accidentally get some on your black parts it can turn them blue.

Kane
05-09-2014, 10:15 PM
But what's the consensus on the vinegar and water idea? It would be very easy to keep a bottle of it around. Any ideas on the proportion of one to the other? Would it be good for the whole car or would it be best to avoid the black parts with it too?

nkemp
05-09-2014, 11:17 PM
The formula ...A few gurgles of vinegar and some amount of warm water until there were a couple inches in the bottom of the bucket. The point is that I just mixed up a quart or two and there was nothing scientific about the mix. I didn't have any problems with any of the other surfaces. I soaked the rag, wrung out some and slopped it on the car and washed it. Then I dried it with a towel.

I got the idea from the recommendation of vinegar and water to be used on vinyl flooring and from how well it works as a glass cleaner. It is clear with no other stuff to mess up the finish.

Give it a try. If you are worried, try it on the refrigerator or kitchen sink first. Vinegar and water is not a harsh cleaner and has no abrasives. There is no waxes or oils either so attracting dust is not an issue.

For the louvers I found a SS cleaner with wax that does a great job of removing the white and then I put Back to Black on to keep it that way. I know it sounds strange but it works for me and my louvers look like the day they were made. Lots of texture, no shine or filled "pores".

refugeefromcalif
05-10-2014, 12:10 PM
For the louvers I found a SS cleaner with wax that does a great job of removing the white and then I put Back to Black on to keep it that way.

Is this the, Back to Black Tire shine?

George

nkemp
05-10-2014, 01:44 PM
It is Mother's Back-to-Black bumper and trim. BTW ... I did not have great luck just using Back to Black by itself. Used with the SS Cleaner was what seems to make it work best.

jawn101
05-11-2014, 02:31 AM
It is Mother's Back-to-Black bumper and trim. BTW ... I did not have great luck just using Back to Black by itself. Used with the SS Cleaner was what seems to make it work best.

Doesn't the Back to Black use silicone as a component? I have always been leery of using any of those re-blackening products for fear of making it impossible to paint the black urethane down the line, if it ever came to that. Mine are still raw and unpainted but if they get bad enough one day and that's my only choice...

Jonathan
05-11-2014, 09:17 AM
I tried out the liquid BKF yesterday. It's not near as abrasive as the powder. It still seems to have cleaned out the grit/dirt in the panels. You don't get the same "feel" when doing it with the powder, like where you can feel the abrasiveness somewhat. It was more a test of the method and I just tried to follow what was on the bottle (wet, rinse off car, put a small dab of liquid on sponge and then wipe. Rinse off with water and then wipe down with soft, clean cloth.)

Vinegar and water had always been the main staple of household cleaners in the past. Windows of course, but bathroom floors or sinks, etc. too. Windex brand or other cleaners will have other chemicals in it in addition to the action of vinegar. I was told not to use it on the glass front of a fireplace insert for example as it will haze it over. Not sure how it affects other areas on the car, but I stick to using it on the glass and stainless (for fingerprints at car shows). Isn't WD-40 another option for cleaning fingerprints?

nkemp
05-11-2014, 10:48 AM
Doesn't the Back to Black use silicone as a component? ...

I can't answer that one. It does not include an ingredients list. Also, I don't see the product I have on the Mother's site. They have a cleaner which may be similar. The product number for mine is 06108.

paul_haga
05-12-2014, 01:46 PM
This past weekend, I think I found the best combination for cleaning and polishing my car! I'll hand wash my car periodically, but I've never taken it to an auto-wash facility. I do like BKF for really deep cleaning the stainless. And like Nick, I'm a big believer in vinegar on the stainless. I'm also very careful about getting it anywhere else (other than the windows), though.

Here's the first component of my cleaning process:

Windex Multi-Surface Vinegar

http://www.windex.com/en-US/Products/Pages/multi-surface-vinegar.aspx

I spray it onto those soft blue paper towels and then a 2nd round of spraying it onto microfiber. I find that between the two applications, it get's the stainless about as raw and clean as you can get it.

As for polish...I have seriously been on the hunt for a great stainless polish for the last several years. I've tried Zep, Magic American, Cerama Bryte, Sheila Shine, Hope's Perfect Stainless, Simple Green Stainless and several others...even Easy-Off Stainless. I've also tried unconventional products like Windex and WD-40. Nothing has been able to stand up, in my mind, to SS-Glo (DMC). I LOVE SS-Glo and always keep a can handy, but at $27.90/can, it get's spendy! ...Sorry DMC. ;)

That said, this past weekend, I think I found the elusive second polishing component of the process...

Rejuvenate 10 oz. Stainless Steel Cleaner and Polish

http://www.homedepot.com/p/Rejuvenate-10-oz-Stainless-Steel-Cleaner-and-Polish-RJ10SSCLAM/203221081

It's a pump/foam product that you apply to the included microfiber applicator and it has incredible results! Here's a picture of my rear fender after applying...

27135

I took it to a car show this past Saturday and the finger prints just wiped away!


-Paul

JRNY13
05-12-2014, 01:57 PM
Does Rejuvenate darken the stainless like Glow? Also, does it leave it a little oily like Glow?


This past weekend, I think I found the best combination for cleaning and polishing my car! I'll hand wash my car periodically, but I've never taken it to an auto-wash facility. I do like BKF for really deep cleaning the stainless. And like Nick, I'm a big believer in vinegar on the stainless. I'm also very careful about getting it anywhere else (other than the windows), though.

Here's the first component of my cleaning process:

Windex Multi-Surface Vinegar

http://www.windex.com/en-US/Products/Pages/multi-surface-vinegar.aspx

I spray it onto those soft blue paper towels and then a 2nd round of spraying it onto microfiber. I find that between the two applications, it get's the stainless about as raw and clean as you can get it.

As for polish...I have seriously been on the hunt for a great stainless polish for the last several years. I've tried Zep, Magic American, Cerama Bryte, Sheila Shine, Hope's Perfect Stainless, Simple Green Stainless and several others...even Easy-Off Stainless. I've also tried unconventional products like Windex and WD-40. Nothing has been able to stand up, in my mind, to SS-Glo (DMC). I LOVE SS-Glo and always keep a can handy, but at $27.90/can, it get's spendy! ...Sorry DMC. ;)

That said, this past weekend, I think I found the elusive second polishing component of the process...

Rejuvenate 10 oz. Stainless Steel Cleaner and Polish

http://www.homedepot.com/p/Rejuvenate-10-oz-Stainless-Steel-Cleaner-and-Polish-RJ10SSCLAM/203221081

It's a pump/foam product that you apply to the included microfiber applicator and it has incredible results! Here's a picture of my rear fender after applying...

27135

I took it to a car show this past Saturday and the finger prints just wiped away!


-Paul

paul_haga
05-12-2014, 02:07 PM
No oil...no darkening. I don't feel like it has much residue at all. The jury is still out if it's a dust magnet like the other polishes with residue, though. Time will tell...

-Paul

JRNY13
05-12-2014, 07:53 PM
I'd be interested to know, thanks.


No oil...no darkening. I don't feel like it has much residue at all. The jury is still out if it's a dust magnet like the other polishes with residue, though. Time will tell...

-Paul

Aleksander
03-07-2015, 10:31 AM
Maybe I'm a bit slow, but I checked out BKF products and a bit confused about what to choose. I don't remember if I read it in this thread, but I've heard about somebody using one that was liquid, and other using the powder one. Could somebody help me find the correct BKF product? :smile:

Rich
03-08-2015, 02:28 PM
Maybe I'm a bit slow, but I checked out BKF products and a bit confused about what to choose. I don't remember if I read it in this thread, but I've heard about somebody using one that was liquid, and other using the powder one. Could somebody help me find the correct BKF product? :smile:

They both work, both are made by the same company. They probably have the same powder in them, just that one of them is a ready-to-use liquid and the other is dry and you use it with water.

Both are listed here as the first two products: LINK: BKF Products List (http://www.barkeepersfriend.com/premium-household-cleaning-products)

I've used both. Results are same so I wouldn't say there is a "correct" one for our stainless panels. I prefer the liquid for ease of application.

If in doubt get one of each and see which one you like.

mluder
03-09-2015, 02:57 AM
This past weekend, I think I found the best combination for cleaning and polishing my car! I'll hand wash my car periodically, but I've never taken it to an auto-wash facility. I do like BKF for really deep cleaning the stainless. And like Nick, I'm a big believer in vinegar on the stainless. I'm also very careful about getting it anywhere else (other than the windows), though.

Here's the first component of my cleaning process:

Windex Multi-Surface Vinegar

http://www.windex.com/en-US/Products/Pages/multi-surface-vinegar.aspx

I spray it onto those soft blue paper towels and then a 2nd round of spraying it onto microfiber. I find that between the two applications, it get's the stainless about as raw and clean as you can get it.

As for polish...I have seriously been on the hunt for a great stainless polish for the last several years. I've tried Zep, Magic American, Cerama Bryte, Sheila Shine, Hope's Perfect Stainless, Simple Green Stainless and several others...even Easy-Off Stainless. I've also tried unconventional products like Windex and WD-40. Nothing has been able to stand up, in my mind, to SS-Glo (DMC). I LOVE SS-Glo and always keep a can handy, but at $27.90/can, it get's spendy! ...Sorry DMC. ;)

That said, this past weekend, I think I found the elusive second polishing component of the process...

Rejuvenate 10 oz. Stainless Steel Cleaner and Polish

http://www.homedepot.com/p/Rejuvenate-10-oz-Stainless-Steel-Cleaner-and-Polish-RJ10SSCLAM/203221081

It's a pump/foam product that you apply to the included microfiber applicator and it has incredible results! Here's a picture of my rear fender after applying...

27135

I took it to a car show this past Saturday and the finger prints just wiped away!


-Paul

I have used the Windex with vinegar too and it works very well on the stainless and the glass too... One problem I have found is it can leave some streaking if the stainless is hot from being in the sun.
I am headed to Home Depot tomorrow to pick up some Rejuvenate... Verry curious to see how it works.

Cheers
Steven

nkemp
03-09-2015, 10:38 AM
I prefer vinegar and water... no Windex or equivalent. Most prepacjaged cleaners have coloring wich may be the streaking you noticed.

Nick

David T
03-09-2015, 11:00 AM
I prefer vinegar and water... no Windex or equivalent. Most prepacjaged cleaners have coloring wich may be the streaking you noticed.

Nick

Maybe the water is hard in his area causing spotting and streaking.

mluder
03-09-2015, 01:03 PM
I prefer vinegar and water... no Windex or equivalent. Most prepacjaged cleaners have coloring wich may be the streaking you noticed.

Nick


Maybe the water is hard in his area causing spotting and streaking.

The Windex with vinegar doesn't have any dye in it so I doubt it's that.

And the streaking I was referring to comes only from the use of Windex - no water involved. Though it's possible it's some residual minerals from washing left on the car.

Cheers
Steve

Delorean3610
03-09-2015, 01:24 PM
What mix of water and vinegar would work best? And would using one of those water cooler jugs of filtered water would eliminate water spots.

David T
03-09-2015, 02:28 PM
What mix of water and vinegar would work best? And would using one of those water cooler jugs of filtered water would eliminate water spots.

I like Griotsgarage.com for all kinds of cleaning and detailing supplies. They sell a filter to soften water for washing cars. It could be you have some kind of stuff on the surface. You might have to rub with a blending pad to remove it. I know you can get stains from leaves drying on the S/S and you have to rub the metal with a blending pad lightly to get rid of them.

Delorean3610
03-09-2015, 02:45 PM
I don't have any spots on it currently, it's just that my car might be used as the marquee for 151st car show of my town. I want it clean for that!

nkemp
03-09-2015, 05:35 PM
Do not let the water dry on the car. Wash it in the shade, wash a section at a time and wipe it down ASAP to avoid droplets of water drying on the surface. If you get spots, use a damp cloth to remove. Hard water is worse than soft water relative to spotting.

drdelorean
07-23-2015, 11:04 AM
Anyone ever tried Autoglym Metal Polish for the SS ?? Got it recommended but haven't tried it out yet. BTW Autoglyms leather cleaner and vinyl restorer are amazing for the interior!