Log in

View Full Version : Suspension Speedometer Cable Bracket



Conundrum
06-07-2013, 10:45 PM
I need to replace my angle drive/speedometer cable. My car doesn't have the bracket that holds the speedometer cable between the angle drive and hold in the body it goes through. I've only ever seen the metal one on other cars as seen here:

19709

I noticed on DMCH's site this one though:

19710

Along with this:

19711

Which is preferred? Also, are they a PITA to get on (taking off the caliper bolts I think)? If they are a pain, I'll probably just zip-tie it temporarily until I replace all of the brakes.

DMC5180
06-07-2013, 11:55 PM
MATT,

My car has the First bracket. An interesting little side note is that it was the 2nd car to have it. VIN EFFECTIVITY FROM 5179. I will say the wire was broken off on mine when I got the car 19 years. I replaced it back then. I recently was looking at things under there and noticed the wire had broken again but was still attached on one side. I may need to do a repair soon before I loose this one.

I can't say which would be preferred. But a part that isn't there can't break either. (wire support type). Installation is not difficult, but you do have to crack the brake line open that mounts to it.

outatym2001
06-08-2013, 04:39 AM
Your first picture part number 110528 is the preferred one. I have one installed on my D. In fact it broke at the weld where the steel rod is attached to the steel plate. So now the steel rod is sitting in my apartment and the rectangular steel plate is attached to the brake caliper. It's time for me to buy another one.

Installation is not difficult, but you do have to crack the brake line open that mounts to it.

Dennis is correct. You have to disconnect the brake fluid line because it is mounted to the rectangular steel plate. Have some extra DOT 4 brake fluid on hand before beginning this project.
And you have to remove the two brake caliper bolts.

Jonathan
06-08-2013, 09:39 AM
I have the first version of the bracket and it is still sitting in a box. My car came without any type of bracket, but it did have that little plastic nubby connector installed directly to the suspension and holding the cable.

Having said that, my speedometer doesn't work worth a darn. And hasn't for quite some time. I have the plastic connector plus zip ties holding the lower cable in place. I'd like to put this bracket in, but was waiting until I did some brake work.

Which made me think after reading this thread... I wonder if there is any pattern of what sort of cable support you have on your car and whether your speedo works?

Perhaps a poll along these lines:

1.) My speedo works AND I have the top picture bracket.
2.) My speedo works AND I have the second picture bracket.
3.) My speedo works AND I have the plastic connector only (no bracket) and maybe a couple zip ties.
4.) My speedo works AND I only have it held in there with zip ties (no brackets or connectors).
5.) My speedo does NOT work well or at all AND I have the top picture bracket.
6.) My speedo does NOT work well or at all AND I have the second picture bracket.
7.) My speedo does NOT work well or at all AND I have the plastic connector only (no bracket) and maybe a couple zip ties.
8.) My speedo does NOT work well or at all AND I only have it held in there with zip ties (no brackets or connectors).

Or something like that? Are there any options missing?

DMC5180
06-08-2013, 11:18 AM
Jonathan,

Are you sure your car did not have any bracket? Was your Brake Line just hanging in space? It should have been attached to something. The primary purpose of the bracket was a Brake line support the Speedo cable support function was added later.


I have the Wire type bracket and my Speedo works. That said, the Original AD failed at in the low 30K's. This was in 96 on my way to the DOA EXPO in Nashville. When I got back from that trip I replaced the AD with a GRADY rebuilt unit. This is when I discovered my VIN 5180 was supposed to have the Wire Support bracket. The wire part was gone on mine, so I replaced it. I can't really say IF the broken bracket played any roll in the eventual failure of the AD. I have no way of knowing how long it had been that way. I don't recall how many years later it was but the rebuilt AD eventually broke again. I replaced that one with a DMCH (1st Generation) NEW Replacement unit. (still running it today) I bought a spare (1 gen) AD a several years ago for when it DOES break again. SFSG. Maybe that's what it takes to get a good one. Buy a spare and NEVER have to use it. Somehow I don't think I will be that lucky. If I had not bought the spare mine would would have broken during a period when supplies were exhausted. There was a fairly long period between DMCH's 1 GEN (sold out) and the 2 GEN became available.

DavidProehl
06-08-2013, 01:56 PM
My car has been missing this braket since the day I bought it as well. When I looked previously, I swear this was an unavailable part. I'll have to buy one of these now.

DMC5180
06-08-2013, 02:13 PM
My car has been missing this braket since the day I bought it as well. When I looked previously, I swear this was an unavailable part. I'll have to buy one of these now.

It was unavailable for quite some time. They may have had them remanufactured. It's hard too know these days. I used to get periodical E-NEWS updates from DMCH with New Products or remanufactured parts. Apparently they quit sending those out and now just do FACEBOOK announcements. I don't participate in FB. Either that or they lost my E-NEWS subscription during system upgrades.

Jonathan
06-08-2013, 06:13 PM
Good point, Dennis. I may indeed have that second picture bracket and it is together with the plastic clip. I'll have to have a closer look. I bet it is in there, like you suggested. I knew it wasn't the longer, wire one which is why I had thought there were like 3 versions, versus really just two. My speedo is quite craptacular, so I'm looking for reasons or solutions to fix it. I bought the wire bracket from another owner getting rid of excess parts. I think it was very shortly after that when they reappeared as available on the websites. I too think I saw it listed as NLA originally, which is likely why I went looking for a used one.

My suspicion is that at least some of my speedo problems are related to that lower cable not staying aligned or connecting straight into the angle drive. That's my theory anyway. My hope is that when the wire bracket gets installed, it magically starts working :)

Conundrum
06-09-2013, 01:42 AM
My car had never had any bracket. Maybe before I got it, it had something there, but there's nothing now.

Sent from my Samsung Galaxy S3 using Tapatalk 2

DMC5180
06-09-2013, 12:58 PM
My car had never had any bracket. Maybe before I got it, it had something there, but there's nothing now.

Sent from my Samsung Galaxy S3 using Tapatalk 2

I'm curious to See that. Please post a photo of the Caliper attach bolt heads.

DMC5180
06-09-2013, 01:12 PM
I need to replace my angle drive/speedometer cable. My car doesn't have the bracket that holds the speedometer cable between the angle drive and hold in the body it goes through. I've only ever seen the metal one on other cars as seen here:

19709

I noticed on DMCH's site this one though:

19710

Along with this:

19711

Which is preferred? Also, are they a PITA to get on (taking off the caliper bolts I think)? If they are a pain, I'll probably just zip-tie it temporarily until I replace all of the brakes.


NOTE: TOP PHOTO is for LH caliper. SECOND PHOTO is RH Caliper Both are BRAKE LINE Supports (MIRROR IMAGE) The LH side also incorporates the the SPEEDO CABLE SUPPORT

Farrar
06-10-2013, 12:23 PM
9.) My speedometer works and has neither bracket nor zip-ties.