Jonathan1985
06-21-2013, 08:40 PM
Alright, let me start by saying I have never worked on cars before in my life. But, being the proud owner of a classic, unique car, I decided it was time I learn. I have some issues with #2777 that need special attention, so I plan to take it to DMCH in the next month or so to let the experts tend to the more advanced issues.
The car has had some work done before it came to me. Partial engine rebuild, transmission rebuild, new window motors, brake overhaul, etc. After I got it, I had some additional work done by a local mechanic. Brake overhaul again (since the brakes didn't really work when it got to me), new brake master cylinder from DMC (just in case it was part of the problem), Eibach springs and SPAX shocks installed, and cold start valve replaced (since it was totally shot and the car would barely start).
Well, the day before my vacation to Florida, the speedometer cable snapped like a twig. Easy enough to replace, the new ones being quite cheap...but I figured I'd go ahead and get the whole upgrade kit...cable, angle drive, and dust cap. I debated waiting until I get it to DMC and letting them do the angle drive, but generally everywhere I looked said that it was about a one hour job. So why not go ahead and do it myself?
To date, after two parts shipments and several hours of work, I still don't have it all put back together. I've followed all the directions, I don't know where to go from here. Let me try to break it down:
First, couldn't get old angle drive off. Spring was in the way, no matter which direction the wheel was turned. Eventually managed to force it past the spring, with great effort. New angle drive doesn't have the oiling port on the side, as pictured in the instructions, but I figured it was probably lubricated already just as they said.
Next, couldn't remove nut from old angle drive. Seems totally fused to the angle drive, won't rotate, won't budge. So, ordered a replacement nut from DMC.
New nut arrived today. Assembled everything to test, cable and angle drive and dust cover...rotation carried through without issue. Got the car jacked up, realized there was no way I could possibly work it past the spring, in any position.
Used vice grips to compress the spring. After about an hour trying, finally got it compressed enough to start the nut on the threads.
New nut is too big for my 1 1/4" wrench, unlike the old nut, so I had to improvise. Eventually managed to get it tightened. Realized angle drive is scraping against the spring every time I turn the steering wheel. Looks like the old one was doing it all along too...the finish is pretty much worn off that side of the coil.
Finally put the dust cap on the spindle...and the spindle sticks out about half an inch further than it should...just far enough that the dust cap doesn't touch anything else...just hangs there in space.
Realizing I was utterly defeated, something compelled me to test the dust cap on its own, without the spindle. Doesn't fit anyway, it's too big to fit into place like my old one did.
I realize that if I had just changed out the speedometer cable, I'd be fine right now...but this angle drive thing, now that I've started it, I don't see how I can fix this. It's like the parts are all the wrong size...but I've never read any complaints or issues like these when researching for this project. It's like my DeLorean is a one-of-a-kind, totally out of spec car.
Now, I suspect the spring needs to have been rotated a certain way when it was installed, so that it would permit the angle drive to be installed. Because as is, there is no way to line up the angle drive nut without getting the spring out of the way first. And by a lot, not just a little nudge. If I'm right, this part was probably just an oversight on the part of my local mechanic, who didn't think of the spring needing to be oriented a certain way to permit access to the angle drive. But the rest of it doesn't seem right. I'm sure I could force the dust cap in eventually, but the spindle being too long, that's got me totally stumped.
Does any of this make any sense to anyone who's done this before? I am utterly dumbfounded...and after hours in the Oklahoma summer heat/humidity, very close to collapsing.
The car has had some work done before it came to me. Partial engine rebuild, transmission rebuild, new window motors, brake overhaul, etc. After I got it, I had some additional work done by a local mechanic. Brake overhaul again (since the brakes didn't really work when it got to me), new brake master cylinder from DMC (just in case it was part of the problem), Eibach springs and SPAX shocks installed, and cold start valve replaced (since it was totally shot and the car would barely start).
Well, the day before my vacation to Florida, the speedometer cable snapped like a twig. Easy enough to replace, the new ones being quite cheap...but I figured I'd go ahead and get the whole upgrade kit...cable, angle drive, and dust cap. I debated waiting until I get it to DMC and letting them do the angle drive, but generally everywhere I looked said that it was about a one hour job. So why not go ahead and do it myself?
To date, after two parts shipments and several hours of work, I still don't have it all put back together. I've followed all the directions, I don't know where to go from here. Let me try to break it down:
First, couldn't get old angle drive off. Spring was in the way, no matter which direction the wheel was turned. Eventually managed to force it past the spring, with great effort. New angle drive doesn't have the oiling port on the side, as pictured in the instructions, but I figured it was probably lubricated already just as they said.
Next, couldn't remove nut from old angle drive. Seems totally fused to the angle drive, won't rotate, won't budge. So, ordered a replacement nut from DMC.
New nut arrived today. Assembled everything to test, cable and angle drive and dust cover...rotation carried through without issue. Got the car jacked up, realized there was no way I could possibly work it past the spring, in any position.
Used vice grips to compress the spring. After about an hour trying, finally got it compressed enough to start the nut on the threads.
New nut is too big for my 1 1/4" wrench, unlike the old nut, so I had to improvise. Eventually managed to get it tightened. Realized angle drive is scraping against the spring every time I turn the steering wheel. Looks like the old one was doing it all along too...the finish is pretty much worn off that side of the coil.
Finally put the dust cap on the spindle...and the spindle sticks out about half an inch further than it should...just far enough that the dust cap doesn't touch anything else...just hangs there in space.
Realizing I was utterly defeated, something compelled me to test the dust cap on its own, without the spindle. Doesn't fit anyway, it's too big to fit into place like my old one did.
I realize that if I had just changed out the speedometer cable, I'd be fine right now...but this angle drive thing, now that I've started it, I don't see how I can fix this. It's like the parts are all the wrong size...but I've never read any complaints or issues like these when researching for this project. It's like my DeLorean is a one-of-a-kind, totally out of spec car.
Now, I suspect the spring needs to have been rotated a certain way when it was installed, so that it would permit the angle drive to be installed. Because as is, there is no way to line up the angle drive nut without getting the spring out of the way first. And by a lot, not just a little nudge. If I'm right, this part was probably just an oversight on the part of my local mechanic, who didn't think of the spring needing to be oriented a certain way to permit access to the angle drive. But the rest of it doesn't seem right. I'm sure I could force the dust cap in eventually, but the spindle being too long, that's got me totally stumped.
Does any of this make any sense to anyone who's done this before? I am utterly dumbfounded...and after hours in the Oklahoma summer heat/humidity, very close to collapsing.