View Full Version : Frame & Body Galvanising frame
Well my project turned into a frame off. I noticed alot of cracked epoxy on the front end of my frame and shipped it away to find a lot of surface rust (no holes) Will post up pictures shortly. So I figure I will get the frame dealt with in such a manner I do not need to worry about rust again. Two options come up, Powder coating and galvanization. I am leaning towards galvanization as the frame is dipped, ensuring 100% coverage, something powder coating cant do. I could care less about color. Just a few questions about galvanizing:
-Do I need to worry about warpage? I saw a gentleman across the pond welded a strengthening X on the frame for dipping. However grinding the welds off after seems like it would be counter productive as the coating would be lost.
-Anyone have reasons the frame should not be galvanized?
Thanks!
David T
06-23-2013, 10:58 PM
Well my project turned into a frame off. I noticed alot of cracked epoxy on the front end of my frame and shipped it away to find a lot of surface rust (no holes) Will post up pictures shortly. So I figure I will get the frame dealt with in such a manner I do not need to worry about rust again. Two options come up, Powder coating and galvanization. I am leaning towards galvanization as the frame is dipped, ensuring 100% coverage, something powder coating cant do. I could care less about color. Just a few questions about galvanizing:
-Do I need to worry about warpage? I saw a gentleman across the pond welded a strengthening X on the frame for dipping. However grinding the welds off after seems like it would be counter productive as the coating would be lost.
-Anyone have reasons the frame should not be galvanized?
Thanks!
This has been covered in the past. The problems with galvanizing (hot dip zinc coating) include:
The problem of removing the epoxy before dipping (do not underestimate how hard this can be)
Finding a dipper who has a tank big enough and is expert enough to do it properly
Warpage seems to be a minor issue but can happen especially if the frame is rotten
Adds weight especially if not properly drained while still molten
Afterwards you must drill and retap every hole in the frame
About the only advantage powder has is that it won't add weight but it is very difficult to get the frame clean enough and it won't cover inside boxes. It will stay flexible though. You *could* paint over the zinc to keep it looking stock.
David Teitelbaum
I searched before I made the thread but did not find anything. Then I serached again and found this, lots of info.
I see now that the epoxy removal is going to be difficult. I will have to source someone to chemically remove it, I am not interested in doing it by hand.
http://dmctalk.org/showthread.php?2964-Many-questions-about-galvanization
WelmoedJ
06-24-2013, 04:52 AM
I searched before I made the thread but did not find anything. Then I serached again and found this, lots of info.
I see now that the epoxy removal is going to be difficult. I will have to source someone to chemically remove it, I am not interested in doing it by hand.
http://dmctalk.org/showthread.php?2964-Many-questions-about-galvanization
Over here in Europe it's "standard policy" for frame restoration to strip epoxy.
Then use galvanization and finally powder coat the galvanized frame.
Plugging the frame nuts helps a lot if properly done before galvanizing the frame.
You however still will have to check afterwards each of the holes/nuts so they won't be either too narrow or destroy the bolt's thread.
justlooking
06-24-2013, 11:51 AM
Well my project turned into a frame off. I noticed alot of cracked epoxy on the front end of my frame and shipped it away to find a lot of surface rust (no holes) Will post up pictures shortly. So I figure I will get the frame dealt with in such a manner I do not need to worry about rust again. Two options come up, Powder coating and galvanization. I am leaning towards galvanization as the frame is dipped, ensuring 100% coverage, something powder coating cant do. I could care less about color. Just a few questions about galvanizing:
-Do I need to worry about warpage? I saw a gentleman across the pond welded a strengthening X on the frame for dipping. However grinding the welds off after seems like it would be counter productive as the coating would be lost.
-Anyone have reasons the frame should not be galvanized?
Thanks!
If you think galvanizing means never having to worry about rust again, I have a whole parking lot full of galvanized U-Haul car trailers I'd like to show you.
I understand no coating is going to last forever. But my delorean is going to going through the Hell every UHaul trailer is either. It should last a good amount of time.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.