View Full Version : Wonky Door New Metal Handle
hylnder777
06-24-2013, 02:13 PM
Has anyone ever had an issue with the metal door handle replacements fitment? I installed a new metal handle from DMC Garden Grove and it doesn't line up with the black trim on the door. I have replaced the drivers one long ago and its a perfect fit so I've been on this rodeo once before. The originally plastic broken handle lined up perfectly...What am I missing? Called Danny at DMC and sent him some pics, has anybody had this issue before? I don't mean to be picky but I expect the new handle to fit the same if not better than old on did.
Bitsyncmaster
06-25-2013, 09:33 AM
I have a couple of the metal ones when they first came out. I could not get the fit correct so just left my working originals installed. I may got back and try them again someday.
hylnder777
06-25-2013, 12:23 PM
Nice thing about buying from an authorized DMC vender is that they will make it right. I wonder if the one I bought was one of those early metal ones..Glad to know I'm not the only one that's had this issue. There's a fellow here that has a good used original, I know it's plastic but it's so easy to replace, I'll take my chances, a small sacrifice for a nice straight fit.:hihi2:
hylnder777
07-30-2013, 01:50 PM
So, I put a used handle on the car from a member who parted a vehicle out and it's a prefect fit, imagine that! Not sure why the new metal one fit so poorly?
JohnZ
07-30-2013, 05:26 PM
Is the plastic handle really much prone to break? Wouldn't it be good to keep it and just be careful in opening the doors?
And what affects the plastic handle? Cold/hot temperature? Frequent use?
:)
thanks
My car came with one metal and one plastic handle. When I swapped doors on the passenger side, as i was tightening the stud on the metal handle, the stud sheared off. Curse words ensued. So the metal handles wear out just as the plastic ones in my experience...
BABIS
07-31-2013, 04:17 AM
Is the plastic handle really much prone to break? Wouldn't it be good to keep it and just be careful in opening the doors?
And what affects the plastic handle? Cold/hot temperature? Frequent use?
:)
thanks
our president broke the driver handle last winter ;) they suffer freezing temperature...
JohnZ
07-31-2013, 07:58 AM
our president broke the driver handle last winter ;) they suffer freezing temperature...
I wasn't aware of this! That's another thing to put on my list then... :D
BABIS
07-31-2013, 09:09 AM
I wasn't aware of this! That's another thing to put on my list then... :D
I think it's unnecessary putting them on the priority list ;) you have only to open the doors carefullly the next winter :D
up to now Giascarcio is the only one I know who broke an handle.. and he uses the car as a daily driver.. for example my car came with a replaced handle (obviously driver side) and it came from California
JohnZ
07-31-2013, 09:12 AM
I'll put it on the list, but as the last thing to get... together with the side stripe and the rear bumper letters!
Anyway you forgot to say "our BELOVED president!"
:tongue::tongue:
Shuttleman
06-10-2021, 12:33 AM
Metal handles do not fit like the original ones. They leave a gap at the seal and can have a lot of friction because it is forced back on the handle. In short the back of the handle does not fit the door shape. Another “improved” part from the Delorean world that I will have to throw in the garbage to not offense the seller.
Helirich
06-10-2021, 06:40 PM
Metal handles do not fit like the original ones. They leave a gap at the seal and can have a lot of friction because it is forced back on the handle. In short the back of the handle does not fit the door shape. Another “improved” part from the Delorean world that I will have to throw in the garbage to not offense the seller.
Hate to hyjack this thread, but I noticed the pic on your avatar. Can you explain what I'm seeing? (The black out on the rear fender and maybe vents in front of the tire.
Hate to hyjack this thread, but I noticed the pic on your avatar. Can you explain what I'm seeing? (The black out on the rear fender and maybe vents in front of the tire.
The previous owner of Olivier's car cut several holes in the body work for reasons unknown. All four fenders including the front left :O . It has been a mountain of work but he has welded the missing metal back in, smoothed it out, regrained, and has a stock looking panel once again. Olivier is an incredibly skilled fabricator.
DMCH James
06-18-2021, 12:03 PM
Metal handles do not fit like the original ones. They leave a gap at the seal and can have a lot of friction because it is forced back on the handle. In short the back of the handle does not fit the door shape. Another “improved” part from the Delorean world that I will have to throw in the garbage to not offense the seller.
Metal handles do not fit like the original ones. They leave a gap at the seal and can have a lot of friction because it is forced back on the handle. In short the back of the handle does not fit the door shape. Another “improved” part from the Delorean world that I will have to throw in the garbage to not offense the seller.
The complete history of aftermarket DeLorean door handles is as follows...
Original door handles began to fail early on in cold weather environments when the doors would freeze shut in the winter when left outside in snow, ice, etc. People would yank and yank on the handles and they would snap off. Nowadays that fail mostly from fatigue after 40 years of exposure to UV and general use. I'm not sure what the availability of door handles was after the factory closed, but the earliest ad I saw for a metal replacement - handle only, not the entire assembly - was around 1985 or so. These were sand cast in aluminum and really were a pain to install as you had to disassemble the existing handle and re-use all but the handle.
In 2000 or so, DMCH had the first reproductions made - they are identifiable by the "www.delorean.com" on the backside of the finder guard on the handle assembly. We had a total of about 2500 made across 2-3 orders from 2000 through 2013.
Around that time, Ed Uding also had some reproductions made. As a copy of a copy, they had their own set of issues. We bought around 300 or so from Ed between 2016 and 2020 and eventually got unhappy enough with them that we went back to our old supplier, which had gone out of business and the tooling was lost. We re-tooled earlier this year with a new supplier and DMCH units are available now.
Not sure when you bought yours or which version you might have, but as you may know, the first 1000 or so cars had doors made from softer, kirksite dies and not the production tooling. VIN 1472 would likely fall into that category. I agree that NONE of the door handle versions mentioned fit as good as an original - few reproduction parts few DeLoreans or any cars ever do - but these are certainly improved over the originals in terms of durability and cost.
The complete history of aftermarket DeLorean door handles is as follows...
Original door handles began to fail early on in cold weather environments when the doors would freeze shut in the winter when left outside in snow, ice, etc. People would yank and yank on the handles and they would snap off. Nowadays that fail mostly from fatigue after 40 years of exposure to UV and general use. I'm not sure what the availability of door handles was after the factory closed, but the earliest ad I saw for a metal replacement - handle only, not the entire assembly - was around 1985 or so. These were sand cast in aluminum and really were a pain to install as you had to disassemble the existing handle and re-use all but the handle.
In 2000 or so, DMCH had the first reproductions made - they are identifiable by the "www.delorean.com" on the backside of the finder guard on the handle assembly. We had a total of about 2500 made across 2-3 orders from 2000 through 2013.
Around that time, Ed Uding also had some reproductions made. As a copy of a copy, they had their own set of issues. We bought around 300 or so from Ed between 2016 and 2020 and eventually got unhappy enough with them that we went back to our old supplier, which had gone out of business and the tooling was lost. We re-tooled earlier this year with a new supplier and DMCH units are available now.
Not sure when you bought yours or which version you might have, but as you may know, the first 1000 or so cars had doors made from softer, kirksite dies and not the production tooling. VIN 1472 would likely fall into that category. I agree that NONE of the door handle versions mentioned fit as good as an original - few reproduction parts few DeLoreans or any cars ever do - but these are certainly improved over the originals in terms of durability and cost.
Interesting read. I purchased a set of Eds handles in 2018 and they had their own set of issues. Poor fit and alot of friction so much so i had to entirely remove them and lubricate the pivot points as they were unusable as installed on the car out of the box. He has several other cheap copies of parts but blames the customers or denies selling anything when there is any issue.
FABombjoy
06-18-2021, 12:31 PM
the earliest ad I saw for a metal replacement - handle only, not the entire assembly - was around 1985 or so. These were sand cast in aluminum and really were a pain to install as you had to disassemble the existing handle and re-use all but the handle.
I have an unused set of these and they look like a high school metals class project. I'm shocked they were sold for money and I can't imagine installing them without completely refinishing the exterior to match the car. The instructions are written in machinist's shorthand and include no diagrams or anything that would have been helpful to a DIYer. Truly from the wild west era of aftermarket parts.
dmcerik
06-18-2021, 04:17 PM
I have an unused set of these and they look like a high school metals class project. I'm shocked they were sold for money and I can't imagine installing them without completely refinishing the exterior to match the car. The instructions are written in machinist's shorthand and include no diagrams or anything that would have been helpful to a DIYer. Truly from the wild west era of aftermarket parts.
Can confirm on look of those early metal handles. My drivers side had that early version on it from the time I got the car in 1999 until I replaced them last year with a repo pair I got from DeloreanGo. I've been very happy with the fit and function of the pair I got from DeloreanGo.
Ive come across those handles before as well. I just assumed they were some backyard fix! Wow
Drive Stainless
06-19-2021, 02:09 AM
Did anyone ever make a set that matched the profile of the rub strips?
MrChocky
06-19-2021, 08:03 AM
I have a metal one still in its bag with instructions that came with parts for 1005. I need to check what the situation is with what's fitted. Certainly the passenger side door is a very poor fit right now, so some yanking is needed to open the door.
dmcerik
06-22-2021, 11:26 AM
Can confirm on look of those early metal handles. My drivers side had that early version on it from the time I got the car in 1999 until I replaced them last year with a repo pair I got from DeloreanGo. I've been very happy with the fit and function of the pair I got from DeloreanGo.
Here's a picture of my handle fit on my drivers door. Overall I think it's decent.
https://photos.app.goo.gl/aRZD9VQLjjntjb7RA
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.