View Full Version : General WTH -- Odd Pressure Readings???
First some background:
BAE turbo Car (boost OK).
Started and idled OK, hot or cold.
Would not rev over 4000 RPM (neutral).
Accelerated OK, gradually or full throttle, from a stand still up to ~3000, then loss of power -- only symptom was the deep throat sound as if running out fuel but no bronking if throttle held steady at any position).
=======
Primary pressure OK. Control Pressure high when dead cold (54psi then 72psi within 15 seconds).
Replaced the CPR/WUR (1st) => Pressures to specs at all temps.
No significant improvement in rev or performance.
Suspected FD. Placed injectors in separate containers -- delivered ~6oz in 1 minute, ~equal.
Replaced FD => Revs 5000 RPM max (neutral), no significant change in performance.
Replaced CPR/WUR (2nd) => Primary pressure 100. Control Pressure 100 psi.???
Suspected gauge- Swapped back to CPR/WUR(1st), pressures OK.
Blew out return line w/ 120psi air. Line was clean.
Swapped back to CPR/WUR(2nd) => Primary pressure 100psi. Control Pressure 100 psi cold.
What am I missing??? How is it possible for the primary pressure to be 72psi with 2 CPR/WURs and changing NOTHING but swapping for yet another CPR/WUR change the Primary Pressure, much less raise it over the 72psi???
I have always understood that the PPR sets the system pressure (72psi) making it impossible for either pressure to ever be higher as long as the pump is not changed and the return line is clear???
I don't think this has anything to do with the performance problem, necessarily, but WTH?
Any thoughts appreciated!
David T
06-26-2013, 10:54 PM
If it stumbles at high revs it can be a couple of things.
Fuel delivery (not enough at high flows)
Air blockage (dirty filter)
Plugged cat
My personal favorite, high voltage breakdown in the secondary ignition circuit. (bad plugs, cap, rotor, coil, wires).
Because it is a turbo car you can also be leaning out because of air leaks (false air) with all of that extra induction plumbing.
Other less likely causes include valves needing adjustment, low compression because of a cracked piston, etc. Maybe start with a compression test and read the spark plugs. That will tell you the condition of the mechanicals and if you are running rich or lean.
David Teitelbaum
It doesn't do what I would call stumble...it just runs out of power quickly but smoothly at ~3000, a lot like a governor kicking in. If I let off of the accelerator to say 2/3 to 3/4 it will pull fine, press it back down and all you get is the deep throat sound while pulling just the same (unlike when one is running out of fuel...I can hold it down anywhere higher and it will never change.
I thought 6oz in one minute with the plate down was the norm?
I am going to do the test again with a couple of brand new injectors to compare all with...
Tried another new filter...other was clean inside.
I will try dumping it before the cat for sure (but those pressures are bugging me to no end).
Plugs, cap, rotor, wires are new. I tried my D's coil - no change.
(fwiw- I tried another distributor before the pressure weirdness.)
Compression is very good (he had the bottom end beefed up for the turbo a short while before the problem presented itself).
(And I checked it anyway.)
New plugs looked good after running it around (as hard as I dare) 5 min and after 30 min.
Thanks for input!
P.S. any thoughts on the 100 psi pressure?
Spittybug
06-27-2013, 12:47 AM
Sounds like insufficient advance. Is dizzy mechanical advance working smoothly? Advance should be ~ 33* at WOT, 3,000 RPM. As high as maybe 50* at cruise at 3,000 RPM.
Bitsyncmaster
06-27-2013, 09:02 AM
100 PSI is no good. If the return line is clear then the PPR is broken or plugged. I think the 6 oz/min is about normal but a turbo may require more.
Sounds like insufficient advance. Is dizzy mechanical advance working smoothly? Advance should be ~ 33* at WOT, 3,000 RPM. As high as maybe 50* at cruise at 3,000 RPM.The distributor was reworked to limit advance per the BAE installation instructions when the turbo was installed. Tripple checked.
100 PSI is no good. If the return line is clear then the PPR is broken or plugged. I think the 6 oz/min is about normal but a turbo may require more.That's what is puzzling about it...the primary pressure is fine with all but one CPR...how could a CPR cause the primary pressure to go above 72 psi, or change it at all???
The CPR return line goes to the FD, so I thought it might be the passage in the FD, on the way to the port the frequency valve and line to the tank. So, I tried another FD -- SOS.
:hmm:
Yesterday, I removed the return line at the tank and put it in a jug and started it up...Got a little dripping at first... nothing. ???
Disconnected the FD end and manually blew it out with ease. ???
Inspected the PPR for debris etc, again...nothing.
Put the other CPR/WUR on...same as before, ~54psi then 72psi within 15 seconds, cold.:frantic:
David T
06-27-2013, 10:13 AM
I understand you replaced ignition parts and they are new. Just because they are new cannot rule them out as to being the cause. It sounds like an electrical problem because it is very repeatable. I would reinspect each part and verify it's condition and installation.
David Teitelbaum
DMCMW Julee
06-27-2013, 01:49 PM
Ignition problems will not cause erratic/wrong fuel pressure readings.
Erratic/wrong fuel pressures will make the engine run poorly.
(Dave on julee's phone)
Kukem
06-27-2013, 01:57 PM
Ignition problems will not cause erratic/wrong fuel pressure readings.
Erratic/wrong fuel pressures will make the engine run poorly.
(Dave on julee's phone)
The jig is up! Apparently it's been Julee all along giving out the technical information but just letting "Dave" post it. We're on to you... =P
(Sorry I couldn't help myself... back to the topic at hand)
David T
06-27-2013, 03:45 PM
The jig is up! Apparently it's been Julee all along giving out the technical information but just letting "Dave" post it. We're on to you... =P
(Sorry I couldn't help myself... back to the topic at hand)
I understand where you are coming from but since the symptoms do match up with erratic fuel pressures, for the moment I am disregarding them as to the original problem, loss of power above 4,000 RPM's. If the fuel pressures were that bad you would be seeing other symptoms more indicative of a fuel system problem. At this point I am not convinced it is a fuel delivery problem and certainly not a CPR or PPR problem. I agree it is often hard to distinguish which system to blame, ignition or fuel. Right now my bet is on ignition. A 50/50 bet and I could be wrong. More troubleshooting and diagnosis will settle this but for now I would stay with ignition.
David Teitelbaum
Bitsyncmaster
06-27-2013, 06:10 PM
I would think at idle speed your should get a large volume of gas returned to the tank. It should be close to the full flow the pump is capable of delivering.
I agree. Which is why I was thinking it was the FD/PPR. The only thing I can guess right now is that I have two FDs with a problem at the PPR not allowing it to get to the return line. I have seen brake hoses get a flap in them and cause an intermittent blockage, so I'm going to try putting the a spare injector line on at the FD and see what comes out of it...
I been thinking it might have something to do with this section of the FD which I've never heard any one say much about (including that it has a 3rd o-ring). It does align with the CPR/WUR port....
20163
I eliminated the CAT today (no change), but no more time to play with it.
dmc6960
06-28-2013, 01:28 AM
Have you tried removing a shim from the PPR?
Bitsyncmaster
06-28-2013, 08:37 AM
Have you tried removing a shim from the PPR?
I found it takes quite a large shim to bring my pressure up from 70 PSI to 75 PSI. Took about 0.040".
Have you tried removing a shim from the PPR?Yes, on the 2nd FD/PPR, because the primary pressure was 79 psi. It had two, I removed the thin one and it was then OK, at 72 psi.
What are you thinking... -- Again, I can't get past how the CPR/WRU could ever raise the Primary pressure to 100 psi????
Not to mention trying two FD/PPRs... :confused:
Sounds like insufficient advance. Is dizzy mechanical advance working smoothly? Advance should be ~ 33* at WOT, 3,000 RPM. As high as maybe 50* at cruise at 3,000 RPM.
I went back to square one and checked EVERYTHING...the vacuum advance now has a leak (bad!...looked like it had been hot on the bottom side, as did the firewall....), which I am 100% certain was fine before because I marked the main pulley to get an accurate reading after disabling one of the centrifuge weights (the 5000 RPM one per BAE instructions), then applied vacuum at 5-10-15 in hg. per WS manual to check it out.
:swear1: One down, and one to go (hopefully... ;-)
dmc6960
06-30-2013, 12:53 AM
What are you thinking...
Well, that was more of a generic thought process. I too am unsure how the CPR could be directly related to 100psi primary.
I do recall though of an incident one of the MN folks had back in 2006. We were driving back from DCS'06 and his car starting loosing power, eventually to the point where the engine stalled - Luckily right at an exit ramp. Started doing some basic troubleshooting, eventually discovered NO FUEL coming back to the tank through the return line with the fuel pump jumped. The owner then remembed he had just recently replaced his PPR O-rings with ones he got from Hervery. Well, upon removing the PPR the O-rings were absolutely HUGE. They had swelled up in the 10% ethanol gas, all the way to the point of completely choking off the return line. Luckily he just happened to still have the original O-rings with him, and we installed them and were on our way back home with no more problems.
With that said now, I'm going to re-read everything you've written in this thread again. Its situations like these I *almost* wish I still had K-jet on my car to do interactive troubleshooting.
NightFlyer
06-30-2013, 01:51 AM
Well, that was more of a generic thought process. I too am unsure how the CPR could be directly related to 100psi primary.
I do recall though of an incident one of the MN folks had back in 2006. We were driving back from DCS'06 and his car starting loosing power, eventually to the point where the engine stalled - Luckily right at an exit ramp. Started doing some basic troubleshooting, eventually discovered NO FUEL coming back to the tank through the return line with the fuel pump jumped. The owner then remembed he had just recently replaced his PPR O-rings with ones he got from Hervery. Well, upon removing the PPR the O-rings were absolutely HUGE. They had swelled up in the 10% ethanol gas, all the way to the point of completely choking off the return line. Luckily he just happened to still have the original O-rings with him, and we installed them and were on our way back home with no more problems.
With that said now, I'm going to re-read everything you've written in this thread again. Its situations like these I *almost* wish I still had K-jet on my car to do interactive troubleshooting.
This is most interesting, as I was thinking about ordering Hervey's o-rings and replacing my stock ones with his, but perhaps not...
dmc6960
06-30-2013, 01:55 AM
This is most interesting, as I was thinking about ordering Hervey's o-rings and replacing my stock ones with his, but perhaps not...
Let it be said now...
NEVER REPLACE YOUR ORIGINAL PPR O-RINGS UNLESS YOU KNOW FOR 100% CERTAINTY THAT THEY ARE NOT WORKING.
Odds are they are fine, and your hot-start issue is something else. (Bad accumulator, bad check valve, leaking injectors, leaking fitting).
Let it be said now...
NEVER REPLACE YOUR ORIGINAL PPR O-RINGS UNLESS YOU KNOW FOR 100% CERTAINTY THAT THEY ARE NOT WORKING.
Odds are they are fine, and your hot-start issue is something else. (Bad accumulator, bad check valve, leaking injectors, leaking fitting).
AMEN to that!
NightFlyer
06-30-2013, 02:25 AM
Let it be said now...
NEVER REPLACE YOUR ORIGINAL PPR O-RINGS UNLESS YOU KNOW FOR 100% CERTAINTY THAT THEY ARE NOT WORKING.
Odds are they are fine, and your hot-start issue is something else. (Bad accumulator, bad check valve, leaking injectors, leaking fitting).
Sorry for jacking Ron's thread with this - but this is some GOOD info!
I won't be anymore - thanks for the heads-up Jim :thumbup2:
No problem! ..at least you didn't say put a carb on it... :devil:
NightFlyer
06-30-2013, 02:46 AM
I was going to say convert it to L-Jet :deviltail:
Seriously, and pressure readings aside, did you check the throttle spool, micro-switch, and butterfly/TB?
Yeah. It's opening up all the way and the switch is functioning. (...and the plates have good springs ;-)
NightFlyer
06-30-2013, 03:15 AM
Yeah. It's opening up all the way and the switch is functioning. (...and the plates have good springs ;-)
Any unusual smoke from the exhaust?
No, the only symptom is the limited RPM (and the pressure mystery).
Kenny_Z
06-30-2013, 11:11 AM
Let it be said now...
NEVER REPLACE YOUR ORIGINAL PPR O-RINGS UNLESS YOU KNOW FOR 100% CERTAINTY THAT THEY ARE NOT WORKING.
Odds are they are fine, and your hot-start issue is something else. (Bad accumulator, bad check valve, leaking injectors, leaking fitting).
Ugh, I remember doing this. Still had the hot start issue after replacing the accumulator and verifying everything else. Replaced the rings (were bad but not horrible) but I nicked one without knowing it. The problem actually got worse and it took a week to get all the way back around to checking the PPR rings. Once I put in a set without nicking them I had zero issues.
Kenny_Z
06-30-2013, 11:25 AM
I'm not sure if this will even apply since my issue was bad all over the board but have you tried to pull out the distributor to see if shaft has any play? I had an issue in my Nova where I couldn't get a stable idle or power out of it at any speed. I eventually pulled the dizzy and found that the shaft had worn bearings. The rotor must have been rocking around under the cap. I replaced the unit and it solve all my issues.
I'm not sure if this will even apply since my issue was bad all over the board but have you tried to pull out the distributor to see if shaft has any play? I had an issue in my Nova where I couldn't get a stable idle or power out of it at any speed. I eventually pulled the dizzy and found that the shaft had worn bearings. The rotor must have been rocking around under the cap. I replaced the unit and it solve all my issues. Yeah, I even tore it down to ensure the weights were free etc. ...It's like new inside.
NightFlyer
06-30-2013, 03:47 PM
Does the BAE use a wastegate? If so, have you checked that?
Soundkillr
06-30-2013, 05:12 PM
Does the BAE use a wastegate? If so, have you checked that?
The bae does use a wastegate but if memory serves, and this is the car I think it is, the owner had the wastegate welded closed.
Farrar
07-02-2013, 02:32 AM
Shot in the dark: partially-blocked filter screen in the CPR?
The original and one replacement didn't have one...and the 3rd looked clean....
Finally had a chance to get back to "the project".
Got the Advance unit on. All is well there.
99% sure I have the pressure weirdness figured out but I'll know 100% when a good WUR/CPR gets here. That's right three bad units! The "(1st)" one evidently died on me between swapping it out and putting it back on after trying the other FD, which had a piece of screen and a o-ring packed in the PPR return port.... I could have cut the hair pile in half if I would have checked the pressure in between...maybe.
Anyway, I finally figured out a way to get it to point me somewhere:
Removed the FD return line going to the tank to eliminate it.
Put a spare line back on the FD with the loose end going to a clear jug.
Disconnected the line from the WUR/CPR to the FD at the WUR/CPR and put it into the jug.
Put a spare line back on the WUR/CPR and put the loose end into the jug.
(Something had to give itself away!)
At 70F (Jumped RPM Relay):
(1st):
100 Primary Pressure, 100psi Control Pressure. FD return trickling. WUR/CPR return flowing.
I pulled the PPR and spotted a scars in a line on the piston and then found the screen/piece of o-ring (I still can't see how it didn't blow on through unless they had it pinching the edge of the screen.)
Swapped the PPR out of the 1st FD.
72psi Primary Pressure, 68psi Control Pressure. FD return flowing. WUR/CPR return flowing.
No need to go further. Bad WUR/CPR (should have been ~30psi).
(2nd, was good):
72psi Primary Pressure, 72psi Control Pressure. FD return flowing. WUR/CPR return flowing.
No need to go further...
(Original):
72psi Primary Pressure, 72psi Control Pressure. FD return flowing. WUR/CPR return flowing.
No need to go further.
(Finally, a bad spare I had marked, "23psi@70F" (too low) from my D back when):
72psi Primary Pressure, 24psi Control Pressure. FD return flowing. WUR/CPR return flowing.
The pressure rises as it gets warmer fwiw and revs great now parked, but I didn't take it out on t road -- I'm not going to change ANYTHING until the new WUR/CPR gets here (...and I don't want to tear down my monstrosity of a tester over being impatient ;-)
This one confirms test procedures (I hope ;-)
Soooo, I contacted DMCMW.
OH! They were not where I was getting the other units (long story -- don't ask).
Bottom line- I'm thinking with all of them running so high that the Control Pressure was overcoming the FD plunger and starving it of fuel at high RPM...
I'll post end result asap
Maybe all this will help someone somehow in the future...
Installed the new WUR/CPR. Pressures were good throughout the warm up period and all.
It had a few dirty injectors, but running great now... I like the turbozzzzzz ;-)
THANKS to those with input and being a sounding board!!!
Farrar
07-31-2013, 02:48 PM
Congrats! So is the moral of the story that a rebuilt/cleaned CPR is not as good as a brand new one?
No. As I mentioned, I used a DMCMW WUR/CPR, which are rebuilt.
I would say...always use a know good unit for replacement when trouble shooting a true basket case??
And overall, if the VOD is open and the history is unknown, just buy new "everything in there" to begin with ;-)
Farrar
07-31-2013, 03:31 PM
No. As I mentioned, I used a DMCMW WUR/CPR, which are rebuilt.
Oh, my bad -- this part threw me off:
Installed the new WUR/CPR.
Damn, I wish I had time to re-read the threads I post on. :P
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.