View Full Version : Transmission 5-Speed LED gear shift knob
Bitsyncmaster
07-02-2013, 04:16 PM
It's just an idea that poped into my head. It would look so cool but you would need a wire running up to the knob. The shaft could provide the ground.
NightFlyer
07-02-2013, 04:18 PM
It's just an idea that poped into my head. It would look so cool but you would need a wire running up to the knob. The shaft could provide the ground.
Would the shift pattern be illuminated? Where would the bulb be mounted - would you hollow out the ball?
Farrar
07-02-2013, 04:31 PM
Would running a wire up the shaft require hollowing it out? On my car (automatic), the stick is solid metal.
If you wanted some variety, you could use EL wire for the pattern.
Bitsyncmaster
07-02-2013, 04:37 PM
My thoughts would be a black delren ball with the shift pattern in clear plastic. Then the LED would be mounted inside the ball and glued shut. There would be a small pin to connect the wire. I guess you could machine a hollow shaft. These are just dreams of mine. I'm to busy with my other products to start another one.
Ozzie
07-02-2013, 10:46 PM
Cool idea.
I know of one now defunct vendor, who use to make them:
20305
(Click pic for a close up.)
Someone posted installation instructions, they show the wiring up to the knob: Rieger Illuminated Shift Knob Instructons (http://www.peterbeers.net/vw_roadtrip/GTI/GTI_Mods/Rieger_Shift_Knob_Install/rieger_shift_knob_install.htm)
Kenny_Z
07-03-2013, 02:49 AM
I've always thought a lighted flux capacitor in a clear acrylic would look awesome. Especially on a stainless shift arm.
dvonk
07-03-2013, 11:40 AM
dave, you have so many awesome ideas... this sounds incredible.
Bitsyncmaster
07-03-2013, 12:54 PM
A crazy thought came to me today. Maybe the shifter shaft would work as a transformer core. So I could make a primary winding down under the boot (would need an AC power supply) and a secondary winding in the shift ball. That way I could get power to the ball without any wires.
dvonk
07-03-2013, 12:59 PM
that would be even more amazing...
Dangermouse
07-03-2013, 01:07 PM
Would a button-cell battery version be easier to do?
Bitsyncmaster
07-03-2013, 01:11 PM
Would a button-cell battery version be easier to do?
Even with an LED running between 1 to 2 ma. a button cell would not last long.
jawn101
07-03-2013, 01:55 PM
A crazy thought came to me today. Maybe the shifter shaft would work as a transformer core. So I could make a primary winding down under the boot (would need an AC power supply) and a secondary winding in the shift ball. That way I could get power to the ball without any wires.
This is a glimpse into the mind of an evil genius if there ever was one. Keep it up, Dave... :)
PS this idea sounds really cool. I'd love an illuminated knob, but I might give the aforementioned "hollowed-out volcano lair" design a miss.... ;)
wrkey
07-03-2013, 06:49 PM
On an Automatic, how about the wires from the test connection points ran to the shifter and the LEDs are illuminated based on the shifting trans. Then we could have a cool illuminated shifter and "test" the govenor shift points as well. Maybe have the DMC logo... lite each letter for each shift - in 3rd they area all lit. Or perhaps they are in a cool blue in any other point besides drive where they turn to yellow and then Green as you progress through the gears. Perhaps red when in reverse.
Hmmm... that could be fun.
Bitsyncmaster
07-03-2013, 06:57 PM
Another idea:devil:
Machine the shaft to insert a fiber optic "light pipe". Then put the LED under the boot.
NightFlyer
07-03-2013, 07:15 PM
I like it Dave!
I'm working on an alternative illumination project of another part of the car - will reveal if I'm successful!
jawn101
07-03-2013, 07:15 PM
On an Automatic, how about the wires from the test connection points ran to the shifter and the LEDs are illuminated based on the shifting trans. Then we could have a cool illuminated shifter and "test" the govenor shift points as well. Maybe have the DMC logo... lite each letter for each shift - in 3rd they area all lit. Or perhaps they are in a cool blue in any other point besides drive where they turn to yellow and then Green as you progress through the gears. Perhaps red when in reverse.
Hmmm... that could be fun.
Wow, that is such a cool idea! I love it :)
Spittybug
07-04-2013, 01:37 PM
Another idea:devil:
Machine the shaft to insert a fiber optic "light pipe". Then put the LED under the boot.
+1
or simply run a wire up the shaft and heat shrink tube the shaft to hide it.
or use thin gauge copper wire are wrap the entire shaft on the way up. Lacquer the whole thing to insulate it.
Bitsyncmaster
07-04-2013, 06:34 PM
+1
or simply run a wire up the shaft and heat shrink tube the shaft to hide it.
or use thin gauge copper wire are wrap the entire shaft on the way up. Lacquer the whole thing to insulate it.
I could mill a very thin slot in the shaft but it's making the connection to the knob thats the problem since you have to twist it many times to install the knob. I think my transformer idea is the way to go if it works.
If EL is under consideration, why not run EL up one side of the shaft, get it inside the shifter ball routed the right way, then route it down the other side so the shaft is lit up? Or use properly-sized heat shrink tubing to hide most of the wiring?
DMC81
07-05-2013, 04:57 PM
Just had thought, I dont know much about guns but what about the gun sights that glow non stop? I have seen some of those sights that are pretty bright even in the day time. Is that sort of technology that could be put to use for something like this? Just an idea..
jawn101
07-05-2013, 05:31 PM
Just had thought, I dont know much about guns but what about the gun sights that glow non stop? I have seen some of those sights that are pretty bright even in the day time. Is that sort of technology that could be put to use for something like this? Just an idea..
Tritium tubes. I run across those a lot in my other hobbies. They aren't terribly powerful in a well-lit environment like the cabin of a D. Work fine in the dark (as on a watch) or in isolated environments (like the sight of a gun, which is enclosed and coated on the inside to improve visibility) - but in daylight you'd barely see them. Plus they can't be controlled as far as color - the phosphor that the inside of the vial is coated with determines the color for the life of the tube (which is approximately 12.5 years)
DMC81
07-05-2013, 05:35 PM
Tritium tubes. I run across those a lot in my other hobbies. They aren't terribly powerful in a well-lit environment like the cabin of a D. Work fine in the dark (as on a watch) or in isolated environments (like the sight of a gun, which is enclosed and coated on the inside to improve visibility) - but in daylight you'd barely see them. Plus they can't be controlled as far as color - the phosphor that the inside of the vial is coated with determines the color for the life of the tube (which is approximately 12.5 years)
I knew someone would know alot about that stuff..lol
jawn101
07-05-2013, 05:36 PM
I knew someone would know alot about that stuff..lol
They are wicked cool though, I keep one in a custom housing on my keychain. I'm just waiting for the day someone asks me where my plutonium is.... :)
Bitsyncmaster
07-05-2013, 08:29 PM
Tritium tubes. I run across those a lot in my other hobbies. They aren't terribly powerful in a well-lit environment like the cabin of a D. Work fine in the dark (as on a watch) or in isolated environments (like the sight of a gun, which is enclosed and coated on the inside to improve visibility) - but in daylight you'd barely see them. Plus they can't be controlled as far as color - the phosphor that the inside of the vial is coated with determines the color for the life of the tube (which is approximately 12.5 years)
I remember the old radium watch dials. I guess they found out it's not good to be exposed to that.:shocked:
DMC81
07-05-2013, 08:30 PM
They are wicked cool though, I keep one in a custom housing on my keychain. I'm just waiting for the day someone asks me where my plutonium is.... :)
Is it a Delorean key chain? Either way it sounds cool. :woot:
jawn101
07-05-2013, 08:41 PM
I remember the old radium watch dials. I guess they found out it's not good to be exposed to that.:shocked:
Yeah, radium was a fair sight more dangerous. Tritium is a weak beta particle that can't even penetrate a sheet of paper, much less human skin. It is an isotope of hydrogen and completely harmless unless ingested in liquid form or inhaled, and even then it's quite weak.
DMCMW Dave
07-05-2013, 08:43 PM
I saw this at SEMA a few years ago, kind of surprised it has not caught on.
http://www.indy-cator.de/engl/indy-cator-shifter-knob.php
jawn101
07-05-2013, 08:56 PM
Wow, that's really cool. I say we challenge them on "The installation of the INDY-CATOR in the onboard network is just as easy as its programming" by sending a D over :)
DMCMW Dave
07-05-2013, 09:00 PM
Wow, that's really cool. I say we challenge them on "The installation of the INDY-CATOR in the onboard network is just as easy as its programming" by sending a D over :)
German seems a bit rough.
It has an internal motion/position sensor (like an iphone?) that figures out the gear by location and movement. It is only connected to external 12V power. It was pretty cool in person, I suppose the price is a bit prohibitive. Google it and there are some you-tube videos of it working.
jawn101
07-05-2013, 09:07 PM
German seems a bit rough.
It has an internal motion/position sensor (like an iphone?) that figures out the gear by location and movement. It is only connected to external 12V power. It was pretty cool in person, I suppose the price is a bit prohibitive. Google it and there are some you-tube videos of it working.
Oh, wow! Very cool, smart way to do it.
Texas Twister
07-08-2013, 09:17 AM
I think it was sureshifter.com.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.