View Full Version : General Slave Cylinder 4.3 Engine Swap
Alves
07-05-2013, 12:07 AM
How's everyone doing? Just a quick question.
So firstly I'm doing a 4.3 Vortec Engine Swap. Everything's gone pretty well up to now, but I've run into a problem that could be difficult to handle and I'm just curios if you guys would have any better ideas.
When I trying to install the slave cylinder the slave cylinder protrudes one inch beyond the bell housing by one inch and actually hits the vortec engine. I'm using the original transmission.
I know my explaining of the problem was not top notch so if there's anything you don't understand just ask me to clarify.
My current plan is to move the slave cylinder back and cut the throwing bearing fork pin. Im guessing this probably isn't the most efficient way of accomplishing what I want and would love suggestions.
Thanks guys
DMC5180
07-05-2013, 12:22 AM
How thick is your bell housing adapter plate? Can you post a couple photos?
Alves
07-05-2013, 12:41 AM
2034920350
The adapter plate is a half inch thick. I can cut out the adapter plate where there the slave cylinder is inserted. This leaves me with a half inch of obstruction
I think cutting the pin on the fork is a fine idea. However the pin is not very long. I would recommend cutting out a hole on your adapter plate (1/2") and cutting the pin the other 1/2". So long as you move the cylinder forward the exact same distance you hack off the pin it should operate exactly the same.
Nice swap! must be nice working with nice clean parts too!
Alves
07-05-2013, 12:55 AM
I think cutting the pin on the fork is a fine idea. So long as you move the cylinder forward the exact same distance you hack off the pin it should operate exactly the same.
Nice swap! must be nice working with nice clean parts too!
Thanks man. That's exactly my idea. I'm just no mechanic so I always assume there's a better way :)
Sorry, I edited my response. I misread your initial post.
Alves
07-05-2013, 01:02 AM
Sorry, I edited my response. I misread your initial post.
No problem, I appreciate your help!
DMC5180
07-05-2013, 01:05 AM
2034920350
The adapter plate is a half inch thick. I can cut out the adapter plate where there the slave cylinder is inserted. This leaves me with a half inch of obstruction
Can you put a tape measure against the face of the bell housing to show the overhang. It sure looks like less than 1 inch and more like 5/8". Cut a Clearance hole in the Adapter/spacer plate. I know of a couple GM conversions that used a 3/4" spacer plate with out issue.
Alves
07-05-2013, 01:18 AM
Can you put a tape measure against the face of the bell housing to show the overhang. It sure looks like less than 1 inch and more like 5/8". Cut a Clearance hole in the Adapter/spacer plate. I know of a couple GM conversions that used a 3/4" spacer plate with out issue.
It's been measured, its exactly 15/16"
DMC5180
07-05-2013, 01:24 AM
Okay, Sounds like you will be doing some pin cutting then.
vwdmc16
07-05-2013, 03:42 AM
If you cant get a slave to fit, perhaps you could convert to a pull style slave cylinder. A bracket can be fabricated to attach to some of the bolts that hold the trans halves together. No personal experience with this style slave but its popular with air cooled vws and sandrails running VW trans. the only trick might be to find one with the right size bore.
http://www.mooreparts.com/store/product/2931/Hydraulic-Slave-Cylinder/?gclid=CI-2hv7el7gCFUfhQgodK1oAlA
http://images.nitrosell.com/product_images/2/379/LR-798560.JPG
http://images.nitrosell.com/product_images/2/379/CNC300B.JPG
DMCMW Dave
07-05-2013, 10:59 AM
I know of a couple GM conversions that used a 3/4" spacer plate with out issue.
Well - there is an issue. If the plate is too thick, the trans input shaft misses the pilot bearing and Bad Things Happen.
DMC5180
07-05-2013, 11:37 AM
Well - there is an issue. If the plate is too thick, the trans input shaft misses the pilot bearing and Bad Things Happen.
True, I recall Darryl Tinnerstet doing a GM V6 conversion in the 90's. He used a 3/4" plate. I don't know what he did regarding the Pilot bearing to Input shaft (offset). Perhaps a Male/Female bearing housing extension was machined to fit the bearing bore. I'm not sure what is possible given the space limitations.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.