View Full Version : Engine burning up thrmo time switches
Bikercmbc
07-05-2013, 12:40 PM
The car wouldnt start, switched the plugs and it will start and run fine. narrowed it down to the TTS. replaced the TTS with a nos one. car started up just fine after it was replace. the next time tried to start same problem. why would the TTS be getting burned up? starter sometimes sticks and does not spin, could this be sending too many amps to the TTS and burning them up?? or just coincidence and try to replace it again?
DMCMW Dave
07-05-2013, 12:58 PM
The car wouldnt start, switched the plugs and it will start and run fine. narrowed it down to the TTS. replaced the TTS with a nos one. car started up just fine after it was replace. the next time tried to start same problem. why would the TTS be getting burned up? starter sometimes sticks and does not spin, could this be sending too many amps to the TTS and burning them up?? or just coincidence and try to replace it again?
That will happen if it is hooked up backwards. Which should not be possible due to the indexing on the plug, but if someone reversed the wiring (even at the factory) it will burn out the heater.
It can't sent amps, only volts, and 12 volts will not burn out the heater. 12 volts across the switch part of the thermotime switch will burn it out.
Bikercmbc
07-05-2013, 01:16 PM
ok, it shouldn't have been hooked up backwards. I have two more NOS TTS so I guess I will replace it again and see what happens.
Thanks Dave
sdg3205
07-05-2013, 02:16 PM
Dave,
The Lambda switch, also on the Y-pipe with the spade connector... how often do those fail?
My Lambda system/FV kept operating at around 50% no matter what, which led me to believe my O2 sensor and/or lambda switch was toast. I've gone ahead and replaced both but still have to finish putting the intake back together for testing and adjustment, but I was just curious.
I'm going to reset the baseline for the injectors with the bottles, then go for mixture from there.
DMC5180
07-05-2013, 02:16 PM
ok, it shouldn't have been hooked up backwards. I have two more NOS TTS so I guess I will replace it again and see what happens.
Thanks Dave
Gee, are you hoarding NOS TTS's? Can never have too many I guess.
Bikercmbc
07-05-2013, 03:02 PM
Bought out an old dealerships stock of nos parts. Had three of them in the inventory.
DMC5180
07-05-2013, 03:30 PM
Bought out an old dealerships stock of nos parts. Had three of them in the inventory.
Cool, Did you get a left front fender or grooved trunk lid in the deal or any other N/A parts in the acquisition. Out of curiosity who was the Old Dealer?
DMCMW Dave
07-05-2013, 04:13 PM
ok, it shouldn't have been hooked up backwards. I have two more NOS TTS so I guess I will replace it again and see what happens.
Thanks Dave
I'd check for shorts. They are getting too scarce/expensive to blow up as a test.
DMCMW Dave
07-05-2013, 04:15 PM
Dave,
The Lambda switch, also on the Y-pipe with the spade connector... how often do those fail?
My Lambda system/FV kept operating at around 50% no matter what, which led me to believe my O2 sensor and/or lambda switch was toast..
Never seen one fail. For what you are seeing it would have to fail closed. Easy to test, just disconnect it and see if that solves your problem.
OR measure it with an ohm meter. It is a switch. Should be open all the time unless you put it in your freezer for a while.
Delorean02378
07-05-2013, 04:32 PM
Kyle was kind enough to post this for me as he's been helping me get 10989 back on the road. Unfortunately, I'm stuck at work all day today.
I switched the ThermoTime switch out and it fired right up. Let it run for a few minutes then shut it down. Tried it again and it fired right up.
Let it sit for 2 hours and it went back to it's old ways of turning over but not starting. Seems like it's not getting gas (the car has the new fuel/pump combination kit and a new accumulator kit) The car also has the nology stage 1 set up and Kyle just replaced the plugs with new ones from DMCMW
Tried it again on Wednesday and it would turn over but not start. I poured a little gas in the intake and it fired right up.
If you switch out the plugs on the cold start valve it will also fire right up.
Dave could a bad starter have anything to do with it shorting out? It works most of the time but sometimes it just clicks and doesn't turn over. I have an original starter in good condition that (with Kyle's help) can switch out and probably will.
Any suggestions of where to begin testing for shorts? Any other ideas?
Bitsyncmaster
07-05-2013, 04:45 PM
You need to test if the CSV is working. Put a voltmeter on the two CSV pins and when the car is cranking you should get 12 volts if your engine temp is below 95 deg.
Bikercmbc
07-05-2013, 04:50 PM
we did that, with the csv cranking there is no 12v before we replaced the TTS. 12v at the WUR thats why we switched went towards the TTS. once the TTS was replaced the CSV would work briefly. guess we can check that tonight if we are getting the 12v needed at the CSV with the new TTS installed.
Don't know which dealership it was, kirk got the parts from a guy in the ATL area who bought the inventory. no LFF or anything super rare, just the usual gaskets, seals and different parts that are still mostly available.
Delorean02378
07-05-2013, 04:55 PM
we did that, with the csv cranking there is no 12v before we replaced the TTS. 12v at the WUR thats why we switched went towards the TTS. once the TTS was replaced the CSV would work briefly. guess we can check that tonight if we are getting the 12v needed at the CSV with the new TTS installed.
Don't know which dealership it was, kirk got the parts from a guy in the ATL area who bought the inventory. no LFF or anything super rare, just the usual gaskets, seals and different parts that are still mostly available.
With the exception of a brand new NOS Clock still in the original packaging. BINGO! I'll save that one for my dad's car.
Bikercmbc
07-05-2013, 04:59 PM
yeah, didnt know if you wanted everyone to know about it, thats why I left it out.
DMCMW Dave
07-05-2013, 05:25 PM
Kyle was kind enough to post this for me as he's been helping me get 10989 back on the road. Unfortunately, I'm stuck at work all day today.
I switched the ThermoTime switch out and it fired right up. Let it run for a few minutes then shut it down. Tried it again and it fired right up.
Let it sit for 2 hours and it went back to it's old ways of turning over but not starting. Seems like it's not getting gas (the car has the new fuel/pump combination kit and a new accumulator kit) The car also has the nology stage 1 set up and Kyle just replaced the plugs with new ones from DMCMW
Tried it again on Wednesday and it would turn over but not start. I poured a little gas in the intake and it fired right up.
If you switch out the plugs on the cold start valve it will also fire right up.
Dave could a bad starter have anything to do with it shorting out? It works most of the time but sometimes it just clicks and doesn't turn over. I have an original starter in good condition that (with Kyle's help) can switch out and probably will.
Any suggestions of where to begin testing for shorts? Any other ideas?
Not powered by the starter itself. The TTS is actually powered by the same white-red wire that keys the starter. Unless you have some strange wiring problem, if the starter is getting power so is the TTS.
You can test the TTS with an ohm meter. There are two pins on the TTS. IF COLD one pin will measure a short to ground. The other will measure 30ohms or so to ground (this is the heater). If either one measures open to ground, the TTS is bad (or hot - you must do this test with the coolant below about 90F).
I'd start chasing the TTS wiring vs the diagram. You could have a bad connection somewhere in the harness (or a bad ground connection on the engine intake runner ground).
DMCMW Dave
07-05-2013, 05:26 PM
You need to test if the CSV is working. Put a voltmeter on the two CSV pins and when the car is cranking you should get 12 volts if your engine temp is below 95 deg.
If it starts with the plug swap, it works.
DMC5180
07-05-2013, 05:33 PM
Don't know which dealership it was, kirk got the pnight if we are getting the 12v needed at the Carts from a guy in the ATL area who bought the inventory. no LFF or anything super rare, just the usual gaskets, seals and different parts that are still mostly available.
Interesting, My car was sold through Bill Spreen Toyota, Atlanta GA. They are No longer in business. Makes me wonder If the inventory came from them. Guess we will never know.
Thanks anyway.
Bikercmbc
07-05-2013, 05:43 PM
I'd start chasing the TTS wiring vs the diagram. You could have a bad connection somewhere in the harness (or a bad ground connection on the engine intake runner ground).[/QUOTE]
which one is the intake runner ground? is that the one right side when looking at the engine near the back corner, with the quick disconnect?
DMC5180
07-05-2013, 05:48 PM
I'd start chasing the TTS wiring vs the diagram. You could have a bad connection somewhere in the harness (or a bad ground connection on the engine intake runner ground).
which one is the intake runner ground? is that the one right side when looking at the engine near the back corner, with the quick disconnect?[/QUOTE]
Top left next to the ISM. Not sure what the Quick disconnect ground goes to.
Bikercmbc
07-05-2013, 06:24 PM
ok, ill look around and check the grounds and test the TTS tonight. thanks everyone
Bitsyncmaster
07-05-2013, 08:24 PM
If it starts with the plug swap, it works.
That tells you the CSV is working but it was the wiring that can be bad. My car the CSV never worked when I got it. It turned out to be a bad connection in the bulkhead connector. A bad crimp on the pin I would guess but it was on the back side so I just bypassed it.
jawn101
07-05-2013, 08:58 PM
That tells you the CSV is working but it was the wiring that can be bad. My car the CSV never worked when I got it. It turned out to be a bad connection in the bulkhead connector. A bad crimp on the pin I would guess but it was on the back side so I just bypassed it.
+1, I had the same bad pin on the back side as Dave. I removed my rear wall and got into the bulkhead to fix it personally. It's the white 2-pin church connector.
DMC5180
07-05-2013, 09:15 PM
+1, I had the same bad pin on the back side as Dave. I removed my rear wall and got into the bulkhead to fix it personally. It's the white 2-pin church connector.
Jon,
The white 2 Pin connector is for the FV not the CSV. Perhaps yours was a different connector. I had a Pin Back out in the Blue BH Connector (WUR Heater wire).
jawn101
07-05-2013, 09:53 PM
Jon,
The white 2 Pin connector is for the FV not the CSV. Perhaps yours was a different connector. I had a Pin Back out in the Blue BH Connector (WUR Heater wire).
No, you're right - that's what I meant. It was the CSV. Thanks for the clarification :)
Delorean02378
07-24-2013, 10:24 PM
First of all, thanks to everyone that responded with ideas. Dave M. you were on the money regarding the bad connection.
Kyle may have solved the problem tonight. Here's a picture of what was replaced. I'll give you one guess which connection was bad and replaced (see picture).
Also, here's a video of 10989 driving around the neighborhood tonight and a picture of the engine. The Stage 1 Exhaust sounds really good. I'll be going out in a couple hours to see if it starts right up again. Pray for me Julee.
No comments on those wheels!!! :smile:
http://www.youtube.com/watch?v=Rb2ME-j09Ec&feature=youtu.be
Still a long way to go but I'm hoping this will be a driving restoration.
DMCMW Dave
07-24-2013, 10:30 PM
Pray for me Julee.
No comments on those wheels!!! :smile:
http://www.youtube.com/watch?v=Rb2ME-j09Ec&feature=youtu.be
Still a long way to go but I'm hoping this will be a driving restoration.
Looks like someone lowered the front and not the back, or put huge tires on the rear. Hard to tell with those wheels I guess.
Delorean02378
07-24-2013, 10:36 PM
Looks like someone lowered the front and not the back, or put huge tires on the rear. Hard to tell with those wheels I guess.
Good catch Dave. The front was lowered with the Eibach shocks and springs and the rear shocks and springs are sitting in the trunk.
DMCMW Julee
07-24-2013, 10:37 PM
Pray for me Julee.
Done!
....and the rear shocks and springs are sitting in the trunk.
where they are helping to hold down the front!
Good to see a D out and about - thanks for the video.
Delorean02378
07-24-2013, 11:19 PM
Fired right up after sitting for two hours. Will keep checking over the next few days.
Today was one of those good days as a Delorean owner!
Grover
07-26-2013, 02:37 PM
Failed check valve on the new all in one fuel unit. Call your DeLorean Vendor and ask to be put on order for the new version of the pump that is being released.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.