PDA

View Full Version : Engine Has anyone tried Davis Unified Ignition distributor caps?



bdmiko
07-10-2013, 05:09 PM
Removing my intake manifold this weekend and while I am at it I thought I would replace the distributor cap, rotor, etc. Came across this at Summit Racing and was wondering if it would actually fit and work:
http://www.summitracing.com/parts/dui-240003rd/overview/year/1982/make/delorean/model/dmc-12

If anyone has comments on these or any experience with these I would appreciate your feedback.

Dangermouse
07-10-2013, 05:18 PM
I'm going to guess NO, as the website lists a GM V6 as the engine for an 1981-1983 DeLorean.

It seems to be for a coil-on-plug design.

bdmiko
07-10-2013, 06:05 PM
Glad I asked. Thought maybe this was a crossover part.

Chris 16409
07-10-2013, 06:19 PM
I would stick to a Bosch Cap. If you have your old one handy search for the part number on eBay. There are still Bosch caps to be had for sale. I believe that Bosch is no longer making new ones, so what's on eBay is older stock. See if you can find a German made one. The newer ones were made in Spain I believe.

Bitsyncmaster
07-10-2013, 06:50 PM
From the photo it looks like an uneven fire cap. It may be something to try.

David T
07-10-2013, 11:45 PM
For all of the time and work it takes to get in there it just makes sense to order the correct parts from your favorite D vender. As long as you are at it you should just go ahead and do a full tune-up including:
Spark Plugs
Distributor cap
Rotor
Ignition wires
Air, fuel, oil filters
Fuel injector seals
New vacuum hoses under the intake manifold
Master water pump kit with all of the hoses, seals and gaskets, "O" rings and idler bearings and belts.

As expensive as the parts may be from the vendors, you rarely save anything shopping for yourself, especially when it doesn't fit or doesn't work right. By the time you figure in delays, return shipping, credit, etc, you wind up spending even more than if you bought it all from a "D" vendor. They will know what you need and will sell you stuff that fits and works.
David Teitelbaum

bdmiko
07-11-2013, 01:45 AM
For all of the time and work it takes to get in there it just makes sense to order the correct parts from your favorite D vender. As long as you are at it you should just go ahead and do a full tune-up including:
Spark Plugs
Distributor cap
Rotor
Ignition wires
Air, fuel, oil filters
Fuel injector seals
New vacuum hoses under the intake manifold
Master water pump kit with all of the hoses, seals and gaskets, "O" rings and idler bearings and belts.

As expensive as the parts may be from the vendors, you rarely save anything shopping for yourself, especially when it doesn't fit or doesn't work right. By the time you figure in delays, return shipping, credit, etc, you wind up spending even more than if you bought it all from a "D" vendor. They will know what you need and will sell you stuff that fits and works.
David Teitelbaum

Makes sense. The main reason for removing the intake manifold was for better access to the clutch slave cylinder, water pump and vacuum hoses. But while I was in there I thought it may be worthwhile to replace some more things.

Would it also make sense to replace the vacuum switch, thermistor and lambda switch?

DMC5180
07-11-2013, 02:05 AM
Would it also make sense to replace the vacuum switch, thermistor and lambda switch?

Not worth it IMO. The Failure rates on those are EXTREMELY LOW. However, You should make sure the contact tabs are clean and free of any Green corrosion. It also would not hurt to put dab of Dielectric grease on the male/female terminals for good measure.

David T
07-11-2013, 10:56 AM
Makes sense. The main reason for removing the intake manifold was for better access to the clutch slave cylinder, water pump and vacuum hoses. But while I was in there I thought it may be worthwhile to replace some more things.

Would it also make sense to replace the vacuum switch, thermistor and lambda switch?

What he said. It can't hurt to test the parts though. Make sure everything is hooked up correctly too. Before reinstalling the intake manifold you should pressure test the cooling system and make sure there are no leaks. Yes, doing the clutch slave cylinder is very easy with the manifold removed.
David Teitelbaum

Ron
07-14-2013, 10:19 AM
Fuel Accumulator discussion moved HERE (http://dmctalk.org/showthread.php?7508-Fuel-Accumulator)
(Post 35) (http://dmctalk.org/showthread.php?7508-Fuel-Accumulator&p=111544&viewfull=1#post111544)