Log in

View Full Version : Plastic vaccum line drivers side engine bay



hylnder777
09-05-2013, 02:55 PM
Does anyone know where this vacuum line goes, "see pic" It seems to go into the drivers side rear left side pontoon thru a hole. It looks like it attached in the engine area near the distributor. I have it capped off as my line is missing and don't know where it goes? I know the computer is behind the driver seat and was wondering if that's where it gets vac for the idle control. Any help is appreciated.
PS, sorry for using your pic, I couldn't find a good one :)
Martin

Vin 3005

NightFlyer
09-05-2013, 03:08 PM
That vacuum line goes to the heater control valve, usually found in the recess between the engine and firewall/bulkhead on the left-hand/passenger side. No. 2 in the diagram below.

It connects on the other end to the A/C Mode Switch. When the mode switch is set to Max A/C, it closes the heater control valve which cuts off the flow of engine heated coolant going to the heater core.

http://store.delorean.com/images/Category/large/7-1-3.gif

Jimmyvonviggle
09-05-2013, 03:54 PM
Mine too is cut, and I have been wondering where this goes in the engine bay.

Can anyone post some pics please?

NightFlyer
09-05-2013, 04:02 PM
Mine too is cut, and I have been wondering where this goes in the engine bay.

Can anyone post some pics please?

Give me a few minutes...

Goes into the vacuum reservoir/canister attached to the heater control valve, in-between the engine and firewall/bulkhead on the passenger side. Video to follow shortly.

21791

NightFlyer
09-05-2013, 04:56 PM
21792


http://www.youtube.com/watch?v=To_JLNCh_QU

hylnder777
09-05-2013, 06:03 PM
Great video, thank you. I hooked up a new hose, now the question I have is, what's on the other side of the pontoon wall? I looked under the driver side rear fender well and found nothing? Where is the part that links the mode switch? Someone said it's behind the driver seat, I'm clueless...Thanks

Jimmyvonviggle
09-05-2013, 06:08 PM
Hey nightflyer that was awfully nice of you. Appreciate that!

NightFlyer
09-05-2013, 07:12 PM
Great video, thank you. I hooked up a new hose, now the question I have is, what's on the other side of the pontoon wall? I looked under the driver side rear fender well and found nothing? Where is the part that links the mode switch? Someone said it's behind the driver seat, I'm clueless...Thanks

Not sure exactly how that line is routed through the cabin, but eventually, it terminates on the other end either at Port 3 of the A/C Mode Switch (#7 in the diagram below) or 't's into another vacuum line behind the dash center stack controls (#2 in the diagram below) that does connect to Port 3 of the switch - not sure which, but should be easy enough to figure out if you're working behind the dash. The vacuum line at issue is #29 in the diagram below. Hope that helps.

From the parts manual diagram, it appears to stay solid as it runs through the pontoon, bulkhead/firewall, and to the termination point behind the dash center stack controls. As it shows straight, I'm guessing that it must enter the cabin somewhere behind driver's seat and then curves to run along the center console and up behind the dash center stack controls.

Perhaps someone with a bit more knowledge on this particular area than myself can assist further.

http://store.delorean.com/images/Category/large/7-3-0.gif

Tillsy
09-08-2013, 10:48 AM
From the parts manual diagram, it appears to stay solid as it runs through the pontoon, bulkhead/firewall, and to the termination point behind the dash center stack controls. As it shows straight, I'm guessing that it must enter the cabin somewhere behind driver's seat and then curves to run along the center console and up behind the dash center stack controls.

Correct, it runs with the harness on the left/driver's side of the centre console.

DMCMW Dave
09-08-2013, 11:55 AM
The hard line starts about two inches from the hot water valve. It is the same line through the pontoon, through the electrical compartment behind the driver, and up the console on the left side. It changes to a rubber line just forward of the shifter. Sometimes this joint is in the console, sometimes just forward of the HVAC panel. The rubber line goes to the mode switch.

NightFlyer
09-08-2013, 03:29 PM
BTW - if you notice coolant spray on the loom cover and underside of the engine cover in my video, it's because my stock/OEM heater control valve is leaking where the pivot shaft of the butterfly penetrates the valve housing. It only leaks upon cold start ups, and even then not much coolant at all (just enough to make a mess). Once everything is warm and expanded the leak stops. You can either replace with a stock/OEM valve, a cross reference of a similar design, or get a fully sealed piston valve and never have to worry about leaks from this valve again.

I purchased the Everco #74612 piston valve from AutoZone for $9.49 plus tax. Will replace it this winter.

http://www.autozone.com/autozone/parts/Everco-Heater-Control-Valve/_/N-91sh0?itemIdentifier=142760_0_3020_

kings1527
05-18-2014, 04:19 AM
Did you get the valve installed yet? I love the idea of a fully sealed unit and never have to deal with it again!

NightFlyer
05-18-2014, 05:57 PM
Did you get the valve installed yet? I love the idea of a fully sealed unit and never have to deal with it again!

Yeah, installed it last year. Been working great without any issues as far as I can tell (haven't used the A/C since installation, as it hasn't been warm enough here to justify it, and I've always been more of a windows down kinda guy anyway). No leaks for me anyway (which is why the old one was replaced - it developed a leak near the butterfly pivot in the body).

Being fully sealed is only one of the benefits - the other two are 1) it's all high grade (maybe even glass lined) nylon composite, and thus will never rust or rot away; and 2) it's all self contained, with no external linkages to get caught up on other hoses/lines that are routed in the same general area.

Dave S. previously noted in a another thread on the subject that such a design creates the potential for the vacuum to pull coolant into the vacuum system/intake upon a complete internal failure. However, their are several layers of protection against such happening inside the housing of the valve, thus even if the piston valve itself were to fail, two other barriers/seals would need to also fail in order for this to actually happen. Personally, I think you have better odds of winning the lottery than this valve failing ever causing coolant to infiltrate the vacuum/intake.

Bill and Steve have been running the same valve on their cars for years now without issue - and you know how much they use their A/C :biggrin:

I personally highly recommend it! :thumbup: