Log in

View Full Version : Post your "must have" and/or "essential" restoration supplies



Rich_NYS
01-21-2014, 01:18 AM
I've had my car for one week and so far I've already made at least 3-4 trips to the hardware & home improvement stores.

I removed an access panel & noticed I'll need some black RTV.....few days later I bought a nice super-gucci heat gun & plastic scrapers....then blending pads & cleaner.....then adhesive remover. Tonite I realized I should get some contact cement and a telescoping magnet.

What are the items you think are ranked as "must have" and/or "essential?" I need to stock up! :cool:

Dangermouse
01-21-2014, 01:21 AM
Super-Gucci ? Don't think I have a designer one :)

NightFlyer
01-21-2014, 01:36 AM
Super-Gucci ? Don't think I have a designer one :)

You really need to get with the times Dermot! Only designer heat guns are worth buying. Although I personally prefer the Hugo Boss heat gun to the Super-Gucci :biggrin:

An 8mm square drain plug socket for changing the oil (assuming you have the stock/OEM plug). Or you can just use a piece of 5/16" square bar stock from Menards like I do.

Rich
01-21-2014, 01:49 AM
Materials and tools that are helpful with restoring a D, most of which come out of lots of threads or experience - most of them are good for any 30+ year old car:

Dielectric grease for when you renew the grounds, assuming the car has seen some moisture over the years.
Cooling system pressure test kit for verifying good integrity of the system and the pressure cap(s).
Torque wrench
1/2in. square drive extensions plus a good Allen key fitting (1/2in. sq x 3/8in. hex) plus a breaker bar if you need to de-torque the doors - a common issue due to PO mistakes. 3/8" sq. drive is NOT OK for this job.
12V test lamp probe. It's amazing how much handier it is than a volt-ohmmeter.
A volt-ohmmeter
The special square wrench to unscrew the OE-style oil pan drain plug!! Size is given in post #3 I now see!
If you get into trouble with the K-Jet then a fuel pressure test kit's good for troubleshooting, and so is a dwell-tach.

And, not so much for restoration work, just for keeping it shiny:
Bar-Keeper's Friend - liquid or powder - deep clean the SS as needed, keep it off the fascias or at least don't scrub them with it...
Your favorite spray stainless cleaner - good for small touch-ups on handprints
Black Again or Maguire's Natural Shine - for black sections of fascias, for louver and side vents and rub strips (keep it off the SS) - NOT ArmorAll

I'm sure the forum will be adding to the list of Essentials. Happy shopping!

ALEXAKOS
01-21-2014, 03:56 AM
HEALTH INSURANCE!!!!!!!!!!!!!!!!!!!:blackeye::blackeye::b lackeye::blackeye:

I almost drilled by ballsacks when the drill tip snapped and bounced it onto my crotch making a hole on my pants between my inner thigh and my right ballsack.

If that went through either my thigh or ballsack (yes I have said ballsack one too many times), it would have been a painful removal cause I had to make the drill work the opposite direction to unwind my pants that were swirled on to the drill!:swear1::swear1:

Not funny:nono:

ALEXAKOS
01-21-2014, 04:01 AM
To extend my emergency list:
- Fire extinguisher
- First aid kit
- Mobile phone ON YOU not near you. If something falls on you or you become trapped (God forbid) that you call someone immediately.

Surprises are nasty most of the times:blackeye:

Rich_NYS
01-21-2014, 09:21 AM
You really need to get with the times Dermot! Only designer heat guns are worth buying. Although I personally prefer the Hugo Boss heat gun to the Super-Gucci :biggrin:


Super-Gucci ? Don't think I have a designer one :)


haha! Wagner Digital heat gun: two-speeds, 250 - 1350 degrees = super-gucci. 8)

Rich_NYS
01-21-2014, 09:27 AM
HEALTH INSURANCE!!!!!!!!!!!!!!!!!!!:blackeye::blackeye::b lackeye::blackeye:

I almost drilled by ballsacks when the drill tip snapped and bounced it onto my crotch making a hole on my pants between my inner thigh and my right ballsack.

If that went through either my thigh or ballsack (yes I have said ballsack one too many times), it would have been a painful removal cause I had to make the drill work the opposite direction to unwind my pants that were swirled on to the drill!:swear1::swear1:

Not funny:nono:

Way too much info...lol :umm:

Jonathan
01-21-2014, 09:56 AM
Patience.

Time.

Money.

Mark D
01-21-2014, 10:10 AM
If you're doing a full on restoration then you'll need a few sets of metric wrenches, sockets, ratchets, screw drivers, pliers, etc. But I'm assuming since you're diving into a car restoration you have basic mechanical skills and most likely already have these tools. In addition I'd also invest in:

-Good air compressor and in line water/oil separator.

-Pneumatic impact wrench w/ impact rated sockets

-Pneumatic orbital sander, disc sander, cutoff wheel, etc.

-Sand blast cabinate and aluminum oxide blast media. Blast cabinates are surprisingly cheap and you'll save hours when you're stripping and prepping parts for refinishing.

-Hydraulic press. These are also much cheaper than you think and you'll find a million uses for it especially if you are working on the suspension, bushings, bearings, etc.

-Torque wrench. Ref service topics ST-09-7-81 and ST-24-10-81 for revised torque specs. Some of the values listed in the original service manual were later updated.

-Copy of the service manual, parts manual, and all service topics if you don't already have copies. Most of this can be found free online ...more info here:

http://dmctalk.org/showthread.php?2866-Searchable-Workshop-Technical-Bulletins-and-Volvo-Engine-Manuals
http://dmcnews.com/files.html
http://dmcnews.com/bulletins/index.html

OverlandMan
01-21-2014, 10:26 AM
12V Power Probe for testing electrical circuits
Patience
Metric tools as others have mentioned
A car lift - I don't have one but damn it would be nice and make certain jobs go so much quicker!!!
Pneumatic tools
Fire extinguisher - not a joke!
Computer to access this forum
Shop manual
Cold beer, Whisky, and an occasional cigar
The ability to let the BTTF stuff roll off
A credit card with a good rewards program - you're going to spend a lot of $$$ on this car!
An understanding wife

Rich_NYS
01-21-2014, 10:48 AM
Good stuff....thanks.

Any suggestions on spray lubricants, cleaners, adhesives or other useful "expendables" to have?

I saw a post where NightFlyer mentioned welding plastic with a cable tie, so I know he must have a few super-gucci McGuyver go-to kit suggestions... :thumbup:

DavidProehl
01-21-2014, 12:10 PM
As far as "expendables": PB Blaster or other similar solution to breakdown rust and losen frozen bolts.

Tools: Dremel with extension cable (http://www.amazon.com/Dremel-225-01-Flex-Shaft-Attachment/dp/B0000302Y8) - Can't tell you how many times the dremel has saved the day. Cutting free bolts that won't come any other way, using a wire brush attachment to polish parts, and misc other uses. Also found that now that I have one I use it for a bunch of other projects.

Bill6298
01-21-2014, 12:54 PM
I have ended up using my "cheap" stubby wrenches more than my regular metric set. Line or Flare Nut wrenches are also helpful from time to time.

Exolis
01-21-2014, 01:58 PM
Cold beer, Whisky, and an occasional cigar
The ability to let the BTTF stuff roll off
A credit card with a good rewards program - you're going to spend a lot of $$$ on this car!
An understanding wife


I was getting worried that these items weren't mentioned yet! Probably the most important ones!

LordFly
01-21-2014, 04:20 PM
HEALTH INSURANCE!!!!!!!!!!!!!!!!!!!:blackeye::blackeye::b lackeye::blackeye:

I almost drilled by ballsacks when the drill tip snapped and bounced it onto my crotch making a hole on my pants between my inner thigh and my right ballsack.

If that went through either my thigh or ballsack (yes I have said ballsack one too many times), it would have been a painful removal cause I had to make the drill work the opposite direction to unwind my pants that were swirled on to the drill!:swear1::swear1:

Not funny:nono:

Haha, I'm sure it wouldn't be funny if you got hurt, but I just about burst out laughing at work reading this!

My recommendation: A wire brush and dielectric grease! So many electrical problems with these things just from corroded connections. I wire brush and dielectric grease EVERY SINGLE electrical connection I have ever touched.

Edit: I'm talking the small fine wire brush, the ones that look like toothbrushes.

ALEXAKOS
01-21-2014, 04:25 PM
Haha, I'm sure it wouldn't be funny if you got hurt, but I just about burst out laughing at work reading this!.

WORD!
Excibit A:
http://img.tapatalk.com/d/14/01/22/2amuvu6y.jpg

NightFlyer
01-21-2014, 05:17 PM
I saw a post where NightFlyer mentioned welding plastic with a cable tie, so I know he must have a few super-gucci McGuyver go-to kit suggestions... :thumbup:

I've been tinkering with cars with my Dad since I was 10 years old. Over the course of 30 years, one tends to acquire a lot of tools - some quite useful, others not so much. I honestly don't recall having ever bought a tool specifically just for the DeLorean (I even already had the 5/16" square bar stock for the oil drain plug, as a lawnmower I previously owned used a similar plug).

And as I'm always on a budget, you learn to improvise and use that which is available to you, even if it isn't always the proper/ideal tool/material for the job at hand :smile:

Then again, compared to others, I haven't had to do too much work on my D, as the original owner stored it in a temp/humidity controlled carcoon for almost its entire life prior to my purchase of it. If you really want to preserve the rubber and foam parts on the car, there's nothing better than a temp/humidity controlled carcoon. Probably the only reason that I can still run the original belts to this day without much of a worry.

One tool that I was particularly glad to have though was a very long needle nose pliers - handy for doing spark plug and fuel injector work without having to remove a bunch of parts just to gain access.

A car cover is nice for winter storage situations where you won't be doing much work to the car - I highly recommend the fitted cover from DMCH.

As other have mentioned, a good air compressor and set of air tools is always nice for working on cars, although I can't say that I've used many on the D - in fact, the only time I ever recall using an compressed air tool on the D was an impact gun to remove the brake caliper bolts. I prefer to remove/apply the wheels lugs manually with a socket wrench.

Some type of ANTI-SEIZE or NEVER-SEIZE is CRUCIAL.

A good socket set is a MUST when working on any car - both standard and metric.

I personally use an old fuel pump when changing the coolant on the D, so as to avoid the introduction of air into the cooling system as much as possible. One of the most important things on a D is a properly functioning cooling system. For my complete coolant change procedure, you can check out the following link:

http://dmctalk.org/showthread.php?7919-My-Delorean-VIN-3305-coming-to-Italy!!&p=125964&viewfull=1#post125964

If I come up with anything else, I'll post as they come to mind. Unfortunately though, trips to pick up tools/materials/supplies/parts is just one of the many joys inherent in working on your car :cool:

Rich_NYS
01-21-2014, 05:46 PM
One tool that I was particularly glad to have though was a very long needle nose pliers - handy for doing spark plug and fuel injector work without having to remove a bunch of parts just to gain access.

True story: Yesterday I thought how I could really use a pair of these when I removed the shifter quadrant plate. There was a screw, a fuse, and a mystery piece of plastic that I wanted to get out. I used two long screwdivers.




I personally use an old fuel pump when changing the coolant on the D, so as to avoid the introduction of air into the cooling system as much as possible. One of the most important things on a D is a properly functioning cooling system. For my complete coolant change procedure, you can check out the following link:

http://dmctalk.org/showthread.php?7919-My-Delorean-VIN-3305-coming-to-Italy!!&p=125964&viewfull=1#post125964



Nice write-up.....

Rich_NYS
01-21-2014, 05:53 PM
My recommendation: A wire brush and dielectric grease! So many electrical problems with these things just from corroded connections. I wire brush and dielectric grease EVERY SINGLE electrical connection I have ever touched.

Edit: I'm talking the small fine wire brush, the ones that look like toothbrushes.

That's a good one, exactly the type of thing I'd like to have on hand. Otherwise, what seems to happen is: I have something apart and realize I really need [or should have] some kinda sealant, adhesive....etc. before putting it back together. If I don't have it on hand, that means not finishing the reassembly until after a trip to the store (which might not be until the next day or two.)

Thanks!

louielouie2000
01-21-2014, 05:54 PM
Good stuff....thanks.

Any suggestions on spray lubricants, cleaners, adhesives or other useful "expendables" to have?

I saw a post where NightFlyer mentioned welding plastic with a cable tie, so I know he must have a few super-gucci McGuyver go-to kit suggestions... :thumbup:

Regarding cleaners, the best thing I ever used on my stainless panels was foaming windex in a can. It's a bit tricky to track down these days, but's it's good stuff and very cheap compared to other products people in the community use. Check amazon if you can't find any at your local retail stores. Obviously it's just a surface cleaner for removing finger prints & dust... makes a great car show spritzer. You'll need a scotch brite pad if the graining on your car is brown/black/dingy looking, though.

If your seat/steering wheel leather is dried out, I've heard good things about using Bag Balm. Apparently it is meant to sooth mother cows chapped udders... but it's supposed to be a cheap miracle cure for leather, too. Look it up on youtube and proceed with caution. It is a petroleum product.

You'll also soon find that keeping all your black trim black is a never ending battle (especially the louvers). There is stuff like Meguire's Back to Black, but it has it's cons, as well. If you ever decide to paint your louvers, that stuff will almost certainly cause your paint to bubble. Regarding trim paint, everyone seems to be using SEM Trim Black these days.

As far as things to keep in your car, like others have mentioned, a fire extinguisher is #1. I'd use one that avoids powders... they're a bitch to clean up after. I'd make some little spade connector electrical jumpers as an emergency backup in case your cooling fan switch (aka "otterstat") or RPM relay or anything like that dies. Do a search on jumpers... with the electrical issues these cars have, they come in handy in a pinch. You might also consider getting a window punch. I've been trapped inside a DeLorean after a wreck, and believe me, it isn't fun. Keeping a small tote bag with various wrenches/screwdrivers, etc is a good idea, too. If your insurance company offers a towing coverage, go for it. You'll need it. AAA will drop you after 3 tows in 1 year. Do a search for RPM conversion charts, and print one out to keep in your glove box. Odds are that your angle drive will die during your ownership, and then you'll be without a speedometer until your replacement comes in the mail.

There's about a thousand things I'm forgetting, but these are some good starting points. Welcome to the fun of DeLorean ownership!! :whip:

Rich_NYS
01-21-2014, 06:01 PM
12V Power Probe for testing electrical circuits
Patience
Metric tools as others have mentioned
A car lift - I don't have one but damn it would be nice and make certain jobs go so much quicker!!!
Pneumatic tools
Fire extinguisher - not a joke!
Computer to access this forum
Shop manual
Cold beer, Whisky, and an occasional cigar
The ability to let the BTTF stuff roll off
A credit card with a good rewards program - you're going to spend a lot of $$$ on this car!
An understanding wife


Great list, I think I have most of it but the lifts I have access to are 30 & 60 miles away (no biggie.)

Chase Freedom started rackin' points already -lol.

Patience & ability to let the BTTF stuff roll off? -Well, work in progress on those...haha! :rant:

Rich_NYS
01-21-2014, 06:08 PM
Regarding cleaners, the best thing I ever used on my stainless panels was foaming windex in a can.

Have you tried scotch-brite's foaming cleaner? I haven't yet, but my wife said she has & loves it.


You'll also soon find that keeping all your black trim black is a never ending battle (especially the louvers). There is stuff like Meguire's Back to Black, but it has it's cons, as well. If you ever decide to paint your louvers, that stuff will almost certainly cause your paint to bubble. Regarding trim paint, everyone seems to be using SEM Trim Black these days.

Paining the black trim is on my to-do list for this summer, good heads up on the bubbling....thanks.



You might also consider getting a window punch.

My brother joked about getting me one for Christmas....not such a bad idea after all, I guess!




There's about a thousand things I'm forgetting, but these are some good starting points. Welcome to the fun of DeLorean ownership!! :whip: Thanks man, and I appreciate the suggestions. :thumbup:

Dangermouse
01-21-2014, 06:08 PM
Caught this on TV at the weekend. New homeowner doing some gardening DIY.

Point here being - make sure you know who to use the tool correctly


http://www.youtube.com/watch?v=qUjgmSh9bmE

Jonathan
01-21-2014, 08:19 PM
Point here being - make sure you know who to use the tool correctly

Yes! (You beat me to it Dermot)

I got thinking I should add a couple suggestions that are actually tools and not just philosophical or being an idiot (as I did above)... and thought of the multimeter (volt, current, etc.) as well as perhaps a First Aid kit.

But part of what came to mind was only getting tools you know what to do with or are willing and able to learn how to use. The voltmeter is a good example. It's a valuable tool if you know what to do with it, but useless if you're not sure how it works or what to do with the info you get from testing.

Wrenches don't exactly require a training course, but if you start a job you don't feel very confident doing, then put the tool in someone else's hand (fuel accumulator, exhaust manifold gaskets, brake lines, etc.)

Rich_NYS
01-21-2014, 09:07 PM
Patience.

Time.

Money.

Agreed! :thumbup:

Rich_NYS
01-21-2014, 09:11 PM
Yes! (You beat me to it Dermot)

I got thinking I should add a couple suggestions that are actually tools and not just philosophical or being an idiot (as I did above)... and thought of the multimeter (volt, current, etc.) as well as perhaps a First Aid kit.

lol...WTH you talkin' bout Willis?! I see all good stuff :thumbup:




But part of what came to mind was only getting tools you know what to do with or are willing and able to learn how to use. The voltmeter is a good example. It's a valuable tool if you know what to do with it, but useless if you're not sure how it works or what to do with the info you get from testing.

Wrenches don't exactly require a training course, but if you start a job you don't feel very confident doing, then put the tool in someone else's hand (fuel accumulator, exhaust manifold gaskets, brake lines, etc.)

For sure....my car leaves next weekend for exhaust manifold gaskets & valve adjustment. 8)

DMCMW Dave
01-22-2014, 12:35 AM
-- Can't tell you how many times the dremel has saved the day. --.

Buy lots of the cutoff wheels. They only seem expensive until you figure out how much time they save.

sdg3205
01-22-2014, 01:14 AM
Band aids. Crucial for door work.

Rich_NYS
01-30-2014, 10:19 AM
I have ended up using my "cheap" stubby wrenches more than my regular metric set. Line or Flare Nut wrenches are also helpful from time to time.

I got these last night for $15, seems like a pretty decent set for the price. Good reviews so far.

http://www.homedepot.com/p/Husky-Combo-Wrench-Set-28-Piece-28CW002/204342563

Rich_NYS
01-30-2014, 10:33 AM
-Pneumatic impact wrench w/ impact rated sockets


I got this one last night: http://www.homedepot.com/p/Husky-1-2-in-Impact-Combo-Kit-H4430C/204256358






http://dmctalk.org/showthread.php?2866-Searchable-Workshop-Technical-Bulletins-and-Volvo-Engine-Manuals
http://dmcnews.com/files.html
http://dmcnews.com/bulletins/index.html

Very helpful, I'm lovin' the searchable tech manual.....

David T
01-30-2014, 03:19 PM
I got this one last night: http://www.homedepot.com/p/Husky-1-2-in-Impact-Combo-Kit-H4430C/204256358






Very helpful, I'm lovin' the searchable tech manual.....

What you need is a function of what you intend to be doing. If you are just doing clean-up that is one thing but if you are doing mechanical work there are all kinds of tools and supplies that are required or just nice to have and make the job easier. The 3M S/S cleaner is nice but expensive. Windex is a lot cheaper and works well enough. A blending pad is necessary for scratches. Glass cleaner, leather cleaner/treatment, carpet cleaner, etc. Also important is a good place to work. Preferably with light and heat. The there is the list of stuff to carry when you are out with the car. That depends on it's condition and what you can reasonably expect to do "on the road". Once you start collecting tools you never seem to have enough. I have made some special tools that I have seen others use. For instance, to work on the doors I have a short piece of cable that I hook to keep the door partially open so I can sit on the sill and work inside. There is the jig and other tools to adjust the torsion bars. There is a bunch of special tools to work on the motor and transmission. There are all manner of electrical tools to work on the electrical system. For hand tools you will need Metric and English sockets and wrenches. I could go on and on. It all comes down to what you want to do and your budget.

DMCVegas
01-30-2014, 04:38 PM
The one restoration supply everyone needs:

http://hbcumoney.files.wordpress.com/2013/08/moneystacks.jpg

Mark D
01-30-2014, 05:33 PM
Wow...looks like there's between 800,000 to 1 million dollars in that pile. At first I was thinking more but I don't think it's solid cash all the way through. It looks like there is a black box in the center making it appear like there are more bills there than there really are.

The first thing I was reminded of was the giant block of cash in the storage unit in Breaking Bad.

Either way, point well made :-D