View Full Version : Anybody here vacuform?
TTait
02-26-2014, 01:02 AM
Have been pondering how to recreate the original ripple texture in the vinyl. Urban legend says it was created with some kind of hot press that did not destroy the grain. I understand nobody has been able to reproduce the results. I'll bet you could do it with vacuforming - just a question of how hot to get the vinyl before sucking it down.
Anybody game?
Silverbullet
02-26-2014, 03:53 AM
I am not sure what you want to make.... or what the ripple texture is... We use a hair-cell grain... form up to a 2' x 4' panel... not sure as to the temp, as we look at the sag of the plastic, and judge when it is hot enough, when it sags a certain amount....
Craig
TTait
02-26-2014, 04:27 PM
The oem vinyl has a kind of crinkle texture to it here and there that makes it look more supple - take a look at your knee pads or center console if they are still original. Recovered pieces don't look entirely right without that texture grained into it.
http://store.delorean.com/images/Product/large/110460.jpg
If you think there might be some promise, we could do a test - I have some grey vinyl and am semi local to you...
Tom
Silverbullet
02-26-2014, 06:47 PM
We use MDF (wood) to make molds... and we lock the plastic sheet in place 2'x 4' and it retracts to above heaters... when it sags enough, we send it back over the mold, and the mold raises up into the plastic, and we hit the vacuum.... wait till cool, and remove and trim out...
We do this in Adelanto, CA off 395 at Rancho Rd.
Craig
David T
02-26-2014, 10:55 PM
Vacu-forming is primarily used to reshape plastic that is already molded. An example would be a plastic canopy on an airplane out of a flat sheet. The hard vinyl parts (like the top of the dash) are injection molded from pellets that are melted and then squirted into a mold under high pressure. The mold would have the texture on the inside surfaces which get transferred to the plastic.
mluder
02-26-2014, 11:48 PM
If I understand correctly, I think the objective is to reproduce the texture of the rippled vinyl that covers the center counsel and knee pads... perhaps the vinyl on the rear side trim (speaker) panels?
I'm not sure vacuum forming would do that.
Cheers
Steven
TTait
02-27-2014, 03:00 AM
Exactly - that was my thought. I'm wondering if there is a temp where the vinyl could be heated to that would soften it enough that if pulled down onto a ripple mold with vacuum (grain/finished side up) that you could leave the ripples in place when it cooled.
Wouldn't have to mill the mold for some testing, just find some molds with a similar amount of relief.
SoCalDMC12
02-27-2014, 07:20 AM
Why not use silicon br to make a mold of the vinyl pattern (grain and ripples) and use that to make the vinyl parts?
TTait
02-27-2014, 02:37 PM
The vinyl has a cloth like backing on it for durability - if you laid up vinyl I'm guessing you would have to do a few layers and then and lay in a backing?
The advantage I saw to vacuforming, if it worked, is that you could take an existing sheet of grey of black vinyl and add the ripples in just a few minutes. Once set up someone could spend 30 minutes once every month or two and produce all the vinyl the community could ever use. Nice side job.
Silverbullet
02-27-2014, 08:06 PM
The texture on my elbow rest-console (Very heavy) does not match the Shift panel texture, or the Knee pad texture... We use the Hair-cell texture, it is not smooth, it keeps the pattern even after vacuum forming... I would think the texture of the raw plastic would make the difference...
Craig
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.