View Full Version : 3165's e-brake failed today almost crashed my wifes camaro!
DMC3165
04-12-2014, 10:54 PM
Yup it happened. No pics or anything and this could have been a whole lot worse! So I'll share this as a cautionary tale. I just finished a bunch of work on my car. So I took my son for ice cream just to test my work. Got home and parked my car at the top of my drive which has a somewhat substantial incline. My wife returned home shortly after in her 1 year old SS Camaro. 15 minutes later I was outside doing some yard work when out of the corner my eye I watched 3165 starting to roll right towards my wife's camaro. And believe me it just took off! Fortunately I was 5 feet away. I dropped the hose and ran for the car. No time to open the door whereas the cars were only 10 feet apart. So "like an idiot" I grabbed the back of the car abd used all my might to stop it from hitting the other car. With only inches to spare I stopped it and yelled for my wife to get the F out here. Thankfully she heard me and was able to jump in and push the brake until I could secure the car. Thankfully nothing was damaged and no one got hurt. Could've been a whole lot worse. Just thought I'd share this as a cautionary tale.
DMC3165
04-12-2014, 10:56 PM
Here's a few pics of both cars from last summer
2649426495
NightFlyer
04-12-2014, 11:09 PM
Did a cable snap, or was the e-brake just not adjusted very well?
DMC3165
04-12-2014, 11:12 PM
E-brake could use another adjustment. Possibly pads too.
Jimmyvonviggle
04-12-2014, 11:24 PM
Good thing you didn't get hurt, I mean it's good to save the car but that's pretty crazy.
DMC3165
04-12-2014, 11:45 PM
Good thing you didn't get hurt, I mean it's good to save the car but that's pretty crazy.
Yeah we're nutty car people. My wife and I were just talking about this and she said she'd have done the same thing without hesitation. We are both nuts when it comes to cars always have been. Truthfully we both met street racing back in the 90's. Cars are in our blood!
Hokie
04-13-2014, 12:32 AM
So "like an idiot" I grabbed the back of the car abd used all my might to stop it from hitting the other car. With only inches to spare I stopped it and yelled for my wife to get the F out here.
Wow! You stopped 2800 pounds of rolling awesomeness with your bare hands? We're not worthy! :) Glad everyone and every car is ok!
NightFlyer
04-13-2014, 12:49 AM
E-brake could use another adjustment. Possibly pads too.
Unless you use the e-brake while the car is in motion, the pads never/barely wear.
Glad everything worked out - NICE SAVE :thumbup:
Rich_NYS
04-13-2014, 12:50 AM
Not sure which is more badass: you stopping the car, or the pic of the two cars in your driveway....
(Nice save!)
DMCMW Dave
04-13-2014, 12:27 PM
Unless you use the e-brake while the car is in motion, the pads never/barely wear.
:
But they will fall off the plates.
chris williams
04-13-2014, 01:53 PM
But they will fall off the plates.
Yes we have had a long discussion about this on our own forum, it seems a lot of UK owners have been suffering with this issue.
Chris
NightFlyer
04-13-2014, 02:46 PM
Sounds like pad delamination is a bigger problem than I ever thought it was. Good to know - thanks guys :thumbup:
JohnZ
04-13-2014, 05:36 PM
Man that Camaro is HUGE :eek5: ! I'm not used to big cars, and the Delorean itself is something wider that common cars here in Italy but gosh... the Camaro is a truck! (at least compared to the sleek dmc-12)
:D
Silverbullet
04-13-2014, 05:51 PM
Do you park the car not in reverse? Or do you have an auto? I have a lot more slope than you on my driveway, and with the car in reverse, you can't move it...
Craig
DMC3165
04-13-2014, 06:12 PM
Do you park the car not in reverse? Or do you have an auto? I have a lot more slope than you on my driveway, and with the car in reverse, you can't move it...
Craig
I'm not a huge fan of leaving the car in gear. Years back a friend of mine had a short in his car and the starter spontaneously engaged sending his car right into a guardrail. I generally park mine in the garage which is totally flat and a good pull on the brake handle is more then enough to hold it in place.
In some situations I do leave it in gear but not out of habit. I'm also not a fan of using the drive train to hold the vehicle in place especially for long periods of time. Probably for no good reason just my own neuroses :nervous:
Silverbullet
04-13-2014, 07:21 PM
I have always just left my car in gear, and I have had a lot of cars with stick, Corvette's also you are to put the car in reverse. I am not sure how it could ever hurt the drive train, I would guess the horsepower would put more stress on the drivetrain than the weight of the car.... Most cars the starter motor will not crank without putting the clutch in, I would guess it is a good safety feature...
Craig
Nicholas R
04-13-2014, 10:34 PM
I don't care what vehicle it is, I never rely on the the parking brake. Talking to other manual drivers down here in FL apparently it's uncommon to leave the car in gear. Only thing I could assume is because it's so flat. My firs car was a manual and driving in hilly Cincinnati all the time, I always needed to leave the car in gear. Since then I always have, with every manual car, and always will.
DMC3165
04-14-2014, 05:37 AM
My primary background is commercial trucking. As a rule you never park them in gear. Class 8 trucks have no ignition interrupts like a clutch lockout or anything. After doing that for 18 years it's just force of habit.
Dangermouse
04-14-2014, 01:02 PM
If you fancy a good read, one of the UK owners, Darren C, has posted this outstanding review of the e-brake system
http://www.deloreaneurotec.co.uk/forum/viewtopic.php?f=21&t=4125
as well as ways to improve it.
The British MOT checks the effectiveness of all the brakes, on a rolling road, every year.
Darren has had a collection of British sports cars over the years, so he has good references with this system.
DMCVegas
04-15-2014, 10:21 AM
My primary background is commercial trucking. As a rule you never park them in gear. Class 8 trucks have no ignition interrupts like a clutch lockout or anything. After doing that for 18 years it's just force of habit.
Well now, with all due respect, and remember I said that now, that's an absolute apples to moist towelette comparison. Mechanical control functions of the two work in totally opposite ways.
Pneumatic brakes function totally different from hydraulic ones. Hydraulic brakes need pressure pumped into them via fluid to apply braking force by pushing the friction material against the drum or rotor surface so that the wheel will slow down and stop.
Pneumatic brakes on the other hand are set up as such that there are heavy springs that are always forcing the friction material against the drum surface. The pressure that is pumped into the via compressed air is meant to overcome that spring and pull the friction material AWAY from the drum surface so that the wheel can be free to turn.
So when you push the brake pedal in a hydraulic car, you're pumping pressure into the brakes. When you press the brake pedal on a pneumatic commercial truck, you're actually opening a valve to purge the compressed air out of your brake lines. So when you park a dump truck, an 18-wheeler, or the like, you don't need to worry about placing the truck in gear because it's the equivalent of someone constantly stomping on the brake pedal in your DeLorean because you've completely purged the lines of all pressure. Which of course is why when they tow a truck/truck & trailer that's disabled, you have to screw those long bolts into the actuators to release the brakes.
Now I don't know about other states, but in California and Nevada, you are required to place a manual transmission into gear when parking. The drivetrain is meant to handle it, trust me. Again, it's why so many instruction manuals require you to do so.
As for the parking brake pads themselves, yes, they should be changed out. Sure there is a minuscule amount of wear on pads and shoes (depending upon your vehicle's design) when you reinstall your discs or drums after each brake service and perform your preliminary adjustments. But more importantly are not only the factors of time, but contamination. When you drive through oily puddles you almost immediately after brake and thus scrape/burn off any oil or other contaminates. But parking brake pads don't get that luxury. Most of the time they're applied with the car at a full stop, so they never get cleaned at all. That allows oil to soak in. So yeah, I'd recommend swapping the pads out and adjusting your cables.
And also, put your car in gear when you park it. If engine braking is enough to slow down your car, it's enough to keep it from moving at all when it's stopped.
DMC3165
04-15-2014, 11:09 AM
Well now, with all due respect, and remember I said that now, that's an absolute apples to moist towelette comparison. Mechanical control functions of the two work in totally opposite ways.
Pneumatic brakes function totally different from hydraulic ones. Hydraulic brakes need pressure pumped into them via fluid to apply braking force by pushing the friction material against the drum or rotor surface so that the wheel will slow down and stop.
Pneumatic brakes on the other hand are set up as such that there are heavy springs that are always forcing the friction material against the drum surface. The pressure that is pumped into the via compressed air is meant to overcome that spring and pull the friction material AWAY from the drum surface so that the wheel can be free to turn.
So when you push the brake pedal in a hydraulic car, you're pumping pressure into the brakes. When you press the brake pedal on a pneumatic commercial truck, you're actually opening a valve to purge the compressed air out of your brake lines. So when you park a dump truck, an 18-wheeler, or the like, you don't need to worry about placing the truck in gear because it's the equivalent of someone constantly stomping on the brake pedal in your DeLorean because you've completely purged the lines of all pressure. Which of course is why when they tow a truck/truck & trailer that's disabled, you have to screw those long bolts into the actuators to release the brakes.
Now I don't know about other states, but in California and Nevada, you are required to place a manual transmission into gear when parking. The drivetrain is meant to handle it, trust me. Again, it's why so many instruction manuals require you to do so.
As for the parking brake pads themselves, yes, they should be changed out. Sure there is a minuscule amount of wear on pads and shoes (depending upon your vehicle's design) when you reinstall your discs or drums after each brake service and perform your preliminary adjustments. But more importantly are not only the factors of time, but contamination. When you drive through oily puddles you almost immediately after brake and thus scrape/burn off any oil or other contaminates. But parking brake pads don't get that luxury. Most of the time they're applied with the car at a full stop, so they never get cleaned at all. That allows oil to soak in. So yeah, I'd recommend swapping the pads out and adjusting your cables.
And also, put your car in gear when you park it. If engine braking is enough to slow down your car, it's enough to keep it from moving at all when it's stopped.
Actually your incorrect. The braking system on heavy trucks uses a two chamber system for parking and service brakes. When the air is evacuated for parking a spring brake applies forcing a slack adjuster to turn an s-cam that separates the 2 brake shoes and applies them against the drum. When the system is charged for driving the spring is compressed in abd the second service chamber functions as the operating side every time you push the brake pedal to apply the brakes. Both require a minimum of 60 psi to operate. Anything below 30 and the spring brake automatically comes on stopping the vehicle as a safety precaution.
When I said force of habit I meant leaving the stick in neutral and only applying the parking brake.
DMCVegas
04-15-2014, 07:16 PM
Actually your incorrect. The braking system on heavy trucks uses a two chamber system for parking and service brakes. When the air is evacuated for parking a spring brake applies forcing a slack adjuster to turn an s-cam that separates the 2 brake shoes and applies them against the drum. When the system is charged for driving the spring is compressed in abd the second service chamber functions as the operating side every time you push the brake pedal to apply the brakes. Both require a minimum of 60 psi to operate. Anything below 30 and the spring brake automatically comes on stopping the vehicle as a safety precaution.
When I said force of habit I meant leaving the stick in neutral and only applying the parking brake.
My apologies on the misinformation then. :reading: That apparently is the difference in working with an ancient single-chamber brake with a reservoir tank on trailer and the introduction of the second chamber. Looks like I heard wrong.:what_the: I should have researched that personally beforehand.
But the principal of a parking brake with the two-chamber system is the same. When the system is evacuated of all air and pressure is purged out of both the Service and Parking chambers, it's that massive spring that presses down and still turns the cam to fully engage the brakes for parking. So it's just like having someone stomp the pedal constantly instead of relying upon a secondary set of pads.
I wouldn't worry about leaving the car in gear. It's not going to hurt it one bit. And until this thread, I've never heard of a short engaging a starter motor in any car. But I would though highly consider changing out those old pads, inspecting your forks (trust me, I broke mine), and checking the cable and then re-tensioning it back up.
Kenny_Z
04-16-2014, 12:06 AM
I would have done the same thing but most likely would have been crushed between those two very cool looking cars.
I don't trust the parking brakes in Red either so I always leave her in gear.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.