View Profile: dn010 - DMCTalk Forum

Today, 09:44 AM

dn010 replied to a thread [Frame & Body] Passenger side torsion bar is broken in General DeLorean Discussion

The one thing I never see anyone do or mention is to remove the gas strut first, then opening the door as far as it will go in order to further...

6 replies | 227 view(s)

03-13-2025, 12:13 PM

dn010 replied to a thread [General] Trailing Arm Measurements in General DeLorean Discussion

I have not forgotten about this, should have these for you tomorrow.

6 replies | 419 view(s)

03-13-2025, 12:06 PM

dn010 replied to a thread Looks like the Alpha V is on life support in Open Discussion

I noticed the delorean.com website is all different now too. they finally took down their reservation system. It seems like they just hired whatever...

78 replies | 31051 view(s)

03-11-2025, 05:27 PM

dn010 replied to a thread [General] Trailing Arm Measurements in General DeLorean Discussion

Any specific measurements you?re looking for? I have an old junk one sitting here.

6 replies | 419 view(s)

03-11-2025, 08:32 AM

dn010 replied to a thread Trailing Arm Measurements in General DeLorean Discussion

I have one rotting away outside leaning against the side of my garage that I can measure for you tonight.

1 replies | 158 view(s)

03-10-2025, 02:09 PM

dn010 replied to a thread [Transmission 5-Speed] To clutch or not to clutch in General DeLorean Discussion

Hint: The DeLorean uses the Valeo 52352501 clutch kit. You are not limited to having to buy it from a DeLorean vendor.

4 replies | 315 view(s)

02-26-2025, 01:38 PM

dn010 replied to a thread [Wanted] Adjustable clutch linkage in DeLorean Parts

Thanks man, I'll give that a shot and leave the adjustable linkage as a last resort.

8 replies | 1441 view(s)

02-26-2025, 01:15 PM

dn010 replied to a thread [Wanted] Adjustable clutch linkage in DeLorean Parts

Sometimes the floor mat rides up there and I have to pull it back, so it does happen sometimes but I typically check it and move it down every time I...

8 replies | 1441 view(s)

02-26-2025, 11:58 AM

dn010 replied to a thread [Wanted] Adjustable clutch linkage in DeLorean Parts

My clutch releases extremely close to the floor. New: clutch, pressure plate, T/O bearing, pilot bearing, master cylinder and slave cylinder....

8 replies | 1441 view(s)

02-25-2025, 02:24 PM

dn010 replied to a thread [Suspension] Front wheels far forward in opening (and rear tire clearance) in General DeLorean Discussion

This is what I was trying to allude to also. Most Deloreans I have seen actual numbers for don't even hit the 3.5 they want, they're mostly in the 2s...

78 replies | 7764 view(s)

02-18-2025, 03:42 PM

dn010 replied to a thread [Suspension] Front wheels far forward in opening (and rear tire clearance) in General DeLorean Discussion

Did you measure both with and without the support brackets attached, with the car's weight on all wheels evenly? It was unclear to me in post 37,...

78 replies | 7764 view(s)

02-18-2025, 11:53 AM

dn010 replied to a thread [General] Some more pics of a few pieces i just completed vacuum forming... in General DeLorean Discussion

Your mailbox is full.

5 replies | 967 view(s)