View Profile: Mark413 - DMCTalk Forum

Today, 04:17 AM

Bitsyncmaster replied to a thread 1982 Frame Off Restoration in Johnny Z's DeLorean Restoration Shop

Yes our cars use two relays to power the headlights. That relay kit is good when you still use incandescent bulbs in the running lights (also...

1440 replies | 419417 view(s)

05-19-2025, 02:42 PM

Bitsyncmaster replied to a thread [Electrical] Connectors for Fan fail module in General DeLorean Discussion

Are you looking for male 1/4" crimp terminals?

4 replies | 141 view(s)

05-09-2025, 03:52 PM

Bitsyncmaster replied to a thread [Electrical] AC Panel lights suddenly stopped working in General DeLorean Discussion

You could try black paint around the walls of the push buttons.

18 replies | 841 view(s)

05-09-2025, 03:46 PM

Bitsyncmaster replied to a thread [Electrical] AC Panel lights suddenly stopped working in General DeLorean Discussion

Your not the only one that the light bleed bothered. Looks like I need to do something with the push button decals now.

18 replies | 841 view(s)

05-09-2025, 02:32 PM

Bitsyncmaster replied to a thread Dcs 2025? in DeLorean Events/Car Shows

Yes the old format was nice. I went to four of them. If it's located to far that year just wait another two years. I did go to the one in Florida...

7 replies | 962 view(s)

05-04-2025, 06:11 PM

Bitsyncmaster replied to a thread [General] V-band clamp for GM fuel pump in Custom DeLoreans/Mods

Here it is with the pump installed. I used a 3D printed top hold down plate that is 0.125" inch thick ABS. It does seem strong enough and much less...

41 replies | 27270 view(s)

05-03-2025, 07:40 PM

Bitsyncmaster replied to a thread [General] V-band clamp for GM fuel pump in Custom DeLoreans/Mods

It works great. Ring has one cut and it just snaps over the tank ridge. Simple hose clamp really locks it in place. Hose clamp bought at ACE...

41 replies | 27270 view(s)

04-29-2025, 06:00 PM

Bitsyncmaster replied to a thread [Frame & Body] Door torsion bar stuck in retention plate in General DeLorean Discussion

The splines are twisting a little. I never thought that could happen but when all the torque was off the bracket, it just slipped out with your...

26 replies | 869 view(s)

04-29-2025, 05:26 PM

Bitsyncmaster replied to a thread [Frame & Body] Door torsion bar stuck in retention plate in General DeLorean Discussion

The problem is doing it the conventional way. You have someone holding the counteracting torque while you pull the bracket off to rotate is one...

26 replies | 869 view(s)

04-29-2025, 10:45 AM

Bitsyncmaster replied to a thread [Frame & Body] Door torsion bar stuck in retention plate in General DeLorean Discussion

I only opened vertical. So a long support pole to keep it from closing. I did this all alone.

26 replies | 869 view(s)

04-29-2025, 10:29 AM

Bitsyncmaster replied to a thread [Frame & Body] Door torsion bar stuck in retention plate in General DeLorean Discussion

Yes I have done it on both doors. I think I'm the original owner that posted this first. I did this about 20 years ago after the group at a tech...

26 replies | 869 view(s)

04-29-2025, 08:50 AM

Bitsyncmaster replied to a thread [Frame & Body] Door torsion bar stuck in retention plate in General DeLorean Discussion

With the T panel removed and the door vertical, you can slowly release the tension and the bracket will stop rotating just short off the rear glass. ...

26 replies | 869 view(s)

04-28-2025, 07:57 AM

Bitsyncmaster replied to a thread [General] V-band clamp for GM fuel pump in Custom DeLoreans/Mods

I printed that top plate with ABS. Testing both, it looks like the ABS is very slightly more flexible than PLA. I haven't done a break test yet but...

41 replies | 27270 view(s)

04-27-2025, 07:53 AM

Bitsyncmaster replied to a thread [General] V-band clamp for GM fuel pump in Custom DeLoreans/Mods

I 3D printed the top ring at 0.125" thick and I think it will be strong enough rather then make one in metal. I will look if I can make it thicker...

41 replies | 27270 view(s)

04-26-2025, 05:34 PM

Bitsyncmaster replied to a thread [General] V-band clamp for GM fuel pump in Custom DeLoreans/Mods

I'm convinced this is the way to go. It will wait till I get a chance to replace my glued one. I ordered at T- bolt clamp the for the new one and I...

41 replies | 27270 view(s)

04-26-2025, 08:05 AM

Bitsyncmaster replied to a thread [General] V-band clamp for GM fuel pump in Custom DeLoreans/Mods

I just thought of another way to do the clamp. Could probably get enough flex with the 3D printed ring, so cut a slot so you can clamp it under the...

41 replies | 27270 view(s)

04-26-2025, 07:26 AM

Bitsyncmaster replied to a thread [General] V-band clamp for GM fuel pump in Custom DeLoreans/Mods

Here is the finished clamp installed. It should give you a little more clearance since the pump is clamped all the way down.

41 replies | 27270 view(s)

04-25-2025, 01:07 PM

Bitsyncmaster replied to a thread [General] V-band clamp for GM fuel pump in Custom DeLoreans/Mods

Here is what I have designed right now. Still always thinking about changes. But it looks like this will work. Just a 3D printed ring with 4 holes...

41 replies | 27270 view(s)

04-25-2025, 04:16 AM

Bitsyncmaster replied to a thread [General] V-band clamp for GM fuel pump in Custom DeLoreans/Mods

Look at this photo of the DMCH pump. Probably if the pump had the flat side on the rear it would clear. Now is that pump sitting rotated how it has...

41 replies | 27270 view(s)

04-24-2025, 03:46 PM

Bitsyncmaster replied to a thread [General] V-band clamp for GM fuel pump in Custom DeLoreans/Mods

The fuel pump filter would take care of that. Some of the all in one pumps put it on the outside at the bottom. Most put it inside at the bottom. ...

41 replies | 27270 view(s)

04-23-2025, 03:03 PM

Bitsyncmaster replied to a thread Fuel Pump in DMCTalk F.A.Q. - Frequently Asked Questions

Yes an original or vendor copy of the original sender is wired directly to the fuel gauge. No ECU is required. The problem with that setup is the...

15 replies | 1315 view(s)