No.
Printable View
By the way, most people who have replaced the evaporator/heater core say it's a real nightmare. It's not, really -- you just have to make sure you follow the procedure in the Workshop Manual. First get familiar with the area and how everything fits together, and then when you're following the procedure make note of how many fasteners the book says you have to deal with, because some of them are hard to find. If anything seems stuck, STOP and look for more fasteners, because the box is just plastic and it will break.
We did not remove the dashboard to get the HVAC box out, but the glovebox had already been removed (pending replacement). A trouble light comes in very handy, as will a small flashlight, but really the job is not too bad, in my opinion. It is messy because of the old tar seal that had to be removed and coolant dripping out, and it is time-consuming because of all of the stuff which has to be removed and replaced, but it is not particularly difficult, at least not removing and replacing the HVAC box.
The tricky part, for me, was the part under the wheel well. Here's a tip: put the accumulator on FIRST. The reason I say this is because the hose which runs from the condenser to the evaporator may not have enough play or flex in it for you to have a lot of maneuvering room for when you put the orifice tube in. This was the case on my car, so I found it easier to install the accumulator, then insert the orifice tube and install the bent metal pipe connector, then make sure it was at the right angle to clear the accumulator, before re-attaching the short hose and tightening everything down.
Also, don't force the orifice tube in -- just place it into position, and as you tighten the fitting down that will do the rest of the work for you.
All in all, I'd say it was not a very bad job. But then again, I'm not finished just yet... ;)
Having consulted elsewhere on DMCTalk and also on Facebook, it seems that John Hervey did not include the necessary 90-degree fitting on the end of his short a/c hose (the one that runs from the evaporator to the condenser). He did, however, include that "hub" which contains the high-pressure cutout switch and high-pressure release valve. If you look at the picture here, you will see the entire assembly. I have everything in that picture except for the 90-degree fitting.
I received NOS versions of the high-pressure switch and release valve with the evaporator kit I bought from Dave and Julee. However, without the adapter block I have no way of installing them, so I will need to figure out some way of adapting Hervey's parts to my system.
The fittings for that Hervey hub are exactly the same as those on the bottom left of the condenser, which is where DMC put the adapter block and high pressure relief valve on the later cars. I can install the hub in between the condenser and the hose. The only drawback is that my sight glass will be on the front of the car, and I will have to run two wires from the high pressure switch back to the harness, because the high pressure switch will be located in a different location from stock. However, it should work. I will test this theory on Saturday.
Huh? While I understand if you got a high pressure switch and valve included with your evaporator... Do you not already have a version of each already on that new adapter block Hervey sold you with the short hose (but without the 90º)?
For what its worth, the high pressure relief valve that Hervey sells will NOT screw in to an OEM adapter block, the o-ring seat is different. The same is likely true going the other way.
From what I remember, the hose I got at first was for early vin cars and would not work with the newer accumulators. So I bought his setup with the block, gauge, and switch and that bolted right on. The hose could have used another few inches of length but as long as you run it directly, it worked.
Well, if you want to use Hervey's setup, you'll need to get that 90º. Perhaps you can call him and get one.
If you want to use the OEM adaptor block that goes into the condenser, you're probably going to need another new short hose as well which can reach all the way to the evaporator inlet. The short hose included with Hervey's adapter block would be too short to reach directly to the evaporator, and also wouldn't have the correct curves necessary to make the attachment. Incidentally, if you do have more money to throw at this and want a good working setup without going back to Hervey, I have a spare short hose just for this purpose, and I'll sell it to you for a deal. It will work with or without the OEM style adapter block.
I'm posting this with Tapatalk, so I'm not sure if it will work correctly.
Anyway, today I decided to finish the air conditioning job. As you can see here, the 90-degree fitting is absent from my wheel well.
Attachment 12028
But conveniently, Hervey's "hub" has the same fittings male to female, which means it can be installed on either end of the short hose. I have therefore installed it where the DMC "adapter block" would have gone.
Attachment 12029
As you can see, the sight glass is useless without a mirror. Nonetheless, I don't think I will be using it very often. All I have to do is run a couple of wires for the high-pressure switch, and all should be well.
... eventually ...
... because I connected the system to Stephen's vacuum pump tonight -- the pump to the yellow or "charging" hose from my manifold gauge set, and the red and blue high- and low-pressure hoses to the system as normal. I opened the lines and turned on the pump. When I walked to the front of the car, I heard what sounded like hissing coming from the wheel well. This is far superior to the hissing sound I had coming from underneath the dashboard prior to the evaporator replacement, but it is still bad news. I nonetheless ran the pump for about a half hour, and when I checked the gauges it was reading -5 in. Hg. -- not enough.
The only thing I could think was that I had noticed some slack in the fitting by the orifice tube. I checked it and although I couldn't tighten the fitting anymore, the tube was still swiveling. I disconnected the fitting and checked the O-ring. Although it looked OK, I replaced it with a new one. (I have many spares.) Everything back together, I turned on the pump again and heard the same hissing sound. Turned it off again. Decided to try two O-rings. This seems to have worked. However, I can hear a different sound from the accumulator. It sounds like it was almost coming from inside the accumulator. I double-checked all of the connections and made sure they were all tight, but the sound only changed slightly.
Having got enough mosquito bites for my taste, I decided to call it a night a little early today and post my experience here for you guys to ponder. I plan to try to vacuum the system down again tomorrow when I have more time and it's less skeetery outside. In the meantime... what do y'all think?
Thanks in advance, and sorry for any iPad-related typos.
Farrar
I still won the race.