What have you done to your DeLorean today?

Started cleaning the motor to try and figure out where it's seeping oil from. Tightened down the oil light sender. Does anyone know if there should be a bolt in this hole in the timing cover? It had some oil in it but I don't have any spare bolts that are the right size. I tried one from elsewhere on the timing cover but it didn't feel right - like it wasn't threading and I didn't want to force it. The hole is just below and to the right of the idler pulley bracket, you can see the clip that holds the oil light sender wire.

http://dmctalk.org/attachment.php?at...0&d=1361841900

I got a new WUR/Control Pressure Regulator so today I went to install it. Everything went fine - I removed the old one and put in the new one. The last thing I had to do was tighten up one of the fuel line bolts that goes into the WUR. I over-tightened it and broke the head of the bolt off, leaving the threaded part stuck in the new WUR. This is what happens when novice DIY'ers tries to fiddle with mechanical parts.
I was pretty pissed off because I was going to reinstall the battery and start it up for the first time since November.
Anyway, how the hell do I fix this? Also, the bolt it one of those ones with a little hole under the head (hollow bolt?)- is that something I need to order specifically or can I find one at a hardware store?
How tight are those fuel line bolts supposed to be? I didn't want gas spewing out of them so I thought they should be really tight.

Quote:

---

Originally Posted by pezzonovante88

I got a new WUR/Control Pressure Regulator so today I went to install it. Everything went fine - I removed the old one and put in the new one. The last thing I had to do was tighten up one of the fuel line bolts that goes into the WUR. I over-tightened it and broke the head of the bolt off, leaving the threaded part stuck in the new WUR. This is what happens when novice DIY'ers tries to fiddle with mechanical parts.
I was pretty pissed off because I was going to reinstall the battery and start it up for the first time since November.
Anyway, how the hell do I fix this? Also, the bolt it one of those ones with a little hole under the head (hollow bolt?)- is that something I need to order specifically or can I find one at a hardware store?
How tight are those fuel line bolts supposed to be? I didn't want gas spewing out of them so I thought they should be really tight.

---

You should be able to grab the bolt with some tweezers or something and turn it out, since it's hollow inside. You definitely need to call up a vendor (or a friendly owner with spares) and get the correct replacement. A hardware store won't have it. Torque on these should only be 8 lb/ft.

Quote:

---

Originally Posted by jawn101

You should be able to grab the bolt with some tweezers or something and turn it out, since it's hollow inside. You definitely need to call up a vendor (or a friendly owner with spares) and get the correct replacement. A hardware store won't have it. Torque on these should only be 8 lb/ft.

---

Too late to edit my post, but I should update the above to say that it depends which bolt you snapped what the torque should be. Check section D:02:01 part 10 in your shop manual for the torque spec for the particular size bolt you're dealing with. The smallest ones are ~8 ft/lb but if I'm reading your question above correctly and it's an M14 bolt then it's 11-14 ft/lb

Quote:

---

Originally Posted by jawn101

Too late to edit my post, but I should update the above to say that it depends which bolt you snapped what the torque should be. Check section D:02:01 part 10 in your shop manual for the torque spec for the particular size bolt you're dealing with. The smallest ones are ~8 ft/lb but if I'm reading your question above correctly and it's an M14 bolt then it's 11-14 ft/lb

---

It's the smaller bolt that I snapped.

Quote:

---

Originally Posted by pezzonovante88

I got a new WUR/Control Pressure Regulator so today I went to install it. Everything went fine - I removed the old one and put in the new one. The last thing I had to do was tighten up one of the fuel line bolts that goes into the WUR. I over-tightened it and broke the head of the bolt off, leaving the threaded part stuck in the new WUR. This is what happens when novice DIY'ers tries to fiddle with mechanical parts.
I was pretty pissed off because I was going to reinstall the battery and start it up for the first time since November.
Anyway, how the hell do I fix this? Also, the bolt it one of those ones with a little hole under the head (hollow bolt?)- is that something I need to order specifically or can I find one at a hardware store?
How tight are those fuel line bolts supposed to be? I didn't want gas spewing out of them so I thought they should be really tight.

---

All sorted out now. Got someone at work to fix it. Ordered new bolts and washers.

Quote:

---

Originally Posted by pezzonovante88

All sorted out now. Got someone at work to fix it. Ordered new bolts and washers.

---

Glad to hear it!

Continued to re-assemble the engine from the VOD cleaning. Got to this point as of lastnight:

Attachment 16904

The photo is aptly titled "Almost there...."

Just have to reattach the fuel lines, re-crimp one ground wire, put the alternator belt back on, lock the alternator back in place, hook up the battery, and be glad it's over (: ...

Then I move onto the headliners, driver's door trim, and sun visors!

Quote:

---

Originally Posted by jawn101

Started cleaning the motor to try and figure out where it's seeping oil from. Tightened down the oil light sender. Does anyone know if there should be a bolt in this hole in the timing cover? It had some oil in it but I don't have any spare bolts that are the right size. I tried one from elsewhere on the timing cover but it didn't feel right - like it wasn't threading and I didn't want to force it. The hole is just below and to the right of the idler pulley bracket, you can see the clip that holds the oil light sender wire.

http://dmctalk.org/attachment.php?at...0&d=1361841900

---

Did you ever find out if there is a bolt in that place?

Quote:

---

Originally Posted by dmc3130

Did you ever find out if there is a bolt in that place?

---

Nope... do you have one there? :)

I'm considering taking a fingerful of Right Stuff and just going along the seams of the oil pan to crankcase, crankcase to block, and timing cover to block to see if that stems the mess. It won't be pretty for now, but I think I'm going to have to pull the motor again anyway and put better seals in all these places than we did last time. Could clean it up pretty easily then.