I'll be sure to impress your new neighbors with my work uniform.
Printable View
Halfway through evaporator replacement! Got the box out and disassembled. Now to sand the rusty flaps so I can get new foam to adhere before re-assembling the box with the new evaporator core, etc.
So that's whats you taking so long to get back down here. Someone is playing in the computer.
Good thing Steve posted, else this post would have been combined with my previous one regardless of timestamp.
Quick update since it's past my bedtime: We shut down a little after 9pm.
New foam from Home Depot is on the flaps -- they were rusty and had to be sanded and sprayed clean, but the foam adhered fine and I think it makes a good seal.
The sealing tape supplied with the kit from DMCMW was more than enough to do the job.
The evaporator is installed, but the heater core lines are not.
The accumulator is installed but fittings have not been 100% tightened yet.
Steve left me his vacuum pump. Later this week -- probably this weekend -- I will tighten down those fittings and vacuum out the system one evening, then leave it overnight and check the vacuum reading in the morning.
If we did the work correctly, then I should have amazing a/c when this is all done -- with the exception of the condenser, everything in the system will be less than two years old (I started buying the parts for this project about two years ago with the hoses and compressor; the most recent purchase was the evaporator kit from DMCMW).
I *do* need help adapting this early-style system to accommodate a high-pressure switch and high-pressure release valve, which were provided in the kit I received but are not shown in the workshop manual. If someone could tell me how to install it in my system, that would be most excellent.
Thanks again to Steve for all his help. I hope the ice cream made it worth the trip.
I am tired but happy -- a welcome combination of feelings. I feel like I accomplished something important today! :)
By the way, most people who have replaced the evaporator/heater core say it's a real nightmare. It's not, really -- you just have to make sure you follow the procedure in the Workshop Manual. First get familiar with the area and how everything fits together, and then when you're following the procedure make note of how many fasteners the book says you have to deal with, because some of them are hard to find. If anything seems stuck, STOP and look for more fasteners, because the box is just plastic and it will break.
We did not remove the dashboard to get the HVAC box out, but the glovebox had already been removed (pending replacement). A trouble light comes in very handy, as will a small flashlight, but really the job is not too bad, in my opinion. It is messy because of the old tar seal that had to be removed and coolant dripping out, and it is time-consuming because of all of the stuff which has to be removed and replaced, but it is not particularly difficult, at least not removing and replacing the HVAC box.
The tricky part, for me, was the part under the wheel well. Here's a tip: put the accumulator on FIRST. The reason I say this is because the hose which runs from the condenser to the evaporator may not have enough play or flex in it for you to have a lot of maneuvering room for when you put the orifice tube in. This was the case on my car, so I found it easier to install the accumulator, then insert the orifice tube and install the bent metal pipe connector, then make sure it was at the right angle to clear the accumulator, before re-attaching the short hose and tightening everything down.
Also, don't force the orifice tube in -- just place it into position, and as you tighten the fitting down that will do the rest of the work for you.
All in all, I'd say it was not a very bad job. But then again, I'm not finished just yet... ;)
Having consulted elsewhere on DMCTalk and also on Facebook, it seems that John Hervey did not include the necessary 90-degree fitting on the end of his short a/c hose (the one that runs from the evaporator to the condenser). He did, however, include that "hub" which contains the high-pressure cutout switch and high-pressure release valve. If you look at the picture here, you will see the entire assembly. I have everything in that picture except for the 90-degree fitting.
I received NOS versions of the high-pressure switch and release valve with the evaporator kit I bought from Dave and Julee. However, without the adapter block I have no way of installing them, so I will need to figure out some way of adapting Hervey's parts to my system.
The fittings for that Hervey hub are exactly the same as those on the bottom left of the condenser, which is where DMC put the adapter block and high pressure relief valve on the later cars. I can install the hub in between the condenser and the hose. The only drawback is that my sight glass will be on the front of the car, and I will have to run two wires from the high pressure switch back to the harness, because the high pressure switch will be located in a different location from stock. However, it should work. I will test this theory on Saturday.
Huh? While I understand if you got a high pressure switch and valve included with your evaporator... Do you not already have a version of each already on that new adapter block Hervey sold you with the short hose (but without the 90º)?
For what its worth, the high pressure relief valve that Hervey sells will NOT screw in to an OEM adapter block, the o-ring seat is different. The same is likely true going the other way.
From what I remember, the hose I got at first was for early vin cars and would not work with the newer accumulators. So I bought his setup with the block, gauge, and switch and that bolted right on. The hose could have used another few inches of length but as long as you run it directly, it worked.
Well, if you want to use Hervey's setup, you'll need to get that 90º. Perhaps you can call him and get one.
If you want to use the OEM adaptor block that goes into the condenser, you're probably going to need another new short hose as well which can reach all the way to the evaporator inlet. The short hose included with Hervey's adapter block would be too short to reach directly to the evaporator, and also wouldn't have the correct curves necessary to make the attachment. Incidentally, if you do have more money to throw at this and want a good working setup without going back to Hervey, I have a spare short hose just for this purpose, and I'll sell it to you for a deal. It will work with or without the OEM style adapter block.
I'm posting this with Tapatalk, so I'm not sure if it will work correctly.
Anyway, today I decided to finish the air conditioning job. As you can see here, the 90-degree fitting is absent from my wheel well.
Attachment 12028
But conveniently, Hervey's "hub" has the same fittings male to female, which means it can be installed on either end of the short hose. I have therefore installed it where the DMC "adapter block" would have gone.
Attachment 12029
As you can see, the sight glass is useless without a mirror. Nonetheless, I don't think I will be using it very often. All I have to do is run a couple of wires for the high-pressure switch, and all should be well.
... eventually ...
... because I connected the system to Stephen's vacuum pump tonight -- the pump to the yellow or "charging" hose from my manifold gauge set, and the red and blue high- and low-pressure hoses to the system as normal. I opened the lines and turned on the pump. When I walked to the front of the car, I heard what sounded like hissing coming from the wheel well. This is far superior to the hissing sound I had coming from underneath the dashboard prior to the evaporator replacement, but it is still bad news. I nonetheless ran the pump for about a half hour, and when I checked the gauges it was reading -5 in. Hg. -- not enough.
The only thing I could think was that I had noticed some slack in the fitting by the orifice tube. I checked it and although I couldn't tighten the fitting anymore, the tube was still swiveling. I disconnected the fitting and checked the O-ring. Although it looked OK, I replaced it with a new one. (I have many spares.) Everything back together, I turned on the pump again and heard the same hissing sound. Turned it off again. Decided to try two O-rings. This seems to have worked. However, I can hear a different sound from the accumulator. It sounds like it was almost coming from inside the accumulator. I double-checked all of the connections and made sure they were all tight, but the sound only changed slightly.
Having got enough mosquito bites for my taste, I decided to call it a night a little early today and post my experience here for you guys to ponder. I plan to try to vacuum the system down again tomorrow when I have more time and it's less skeetery outside. In the meantime... what do y'all think?
Thanks in advance, and sorry for any iPad-related typos.
Farrar
I still won the race.
Everyone else, feel free to ignore Steve and post helpful or encouraging comments. I need both right now.
On a positive note, your r134a only cost $6.40 a can before tax. One thing I forgot to mention is to make sure the fittings on your gauge are not leaking. My el cheepo Harbor Freight gauge had a leak on the high side that kept me from being able to get a good vacuum. It would be a good idea to inspect your fittings where the gauge connects to the compressor to ensure you don't hear any hissing noises coming from there as well. I corrected the leak on my gauge by replacing the o rings with some spares I had left over from my $5 o ring kit from O'Reillys.
Hopefully someone else can chime in with some positive comments. I suspect they will be more jealous though because they probably paid $15 a can for their r134a.
You shouldn't have to use two o-rings...look it over real well to see what's up with that.
...you mentioned using the fittings to press the orifice tube in IIRC, did that give you any trouble or seem hard to tighten at all?
If you don't get, say, 10-15 hg within a few seconds, you have a leak.
Hang in there!
Maybe the wrong size O-ring was supplied with the hose. It's possible. The next time I am at the auto parts store I will look for an R-134 O-ring kit. Supposedly they contain all of the O-rings you need and then some. But as of right now, I am in no hurry. I just cleaned up the garage and closed everything.
No. It snapped right in and I tightened the fittings to push it in the rest of the way with almost no resistance.
Well, I don't know what else to do. I've done everything by the book.
Thanks, but I am giving up for now.
If you've already lost the race, there's no point in finishing. Steve taught me this. Thanks, dude. Let me know when you want your vacuum pump back.
Awe man. Don't quit. I was just joking.
Do you still have your old accumulator? I would flush it, install it, and see if you can pull vacuum with it.
Farrar, I think you have already compromised the A/C by not having the 90 degree fitting and moving hoses around to compensate. I think you should take a break and get the fitting from Hervey so you can put it together like I showed in that pic I gave you. You shouldn't need 2 o-rings, that sounds like trouble. You could also try filling with nitrogen, then you could possibly feel the gas escaping and find the leak that way. Just a few ideas.
If you can't find the leak, just put a can of R134a on your charge gauge and only open the valve a little. That should give you time to hear or spray soapy water around the system. The fittings don't need much force since they are o-ring sealed. You should use a little refrigerant oil on the o-rings when you assemble them.
Use Ester oil if you have it (It don't matter for wetting an o-ring), just wet the whole thing.
The idea of sacrificing a $6.40 cent can of r134a sounds like a good idea if it will help to find the leak.
I was about to make another suggestion though, and ask if it is possible.
I have a small 3 gallon air compressor. Could we use this to put some pressure in his system to find the leak? If we could figure out how to connect it to his gauge we could give it a few quick bursts of pressure until he has 30 or so pounds in it. Then all we would ned is some soapy water and we should be able to find the leak.
Would it be possible to do this or would this screw something else up? I certainly want his AC to work so we can be friends again.
Its always more difficult to pull out the moisture than it is to introduce it. Compressed air from an air compressor, especially when run in a very humid environment will introduce a TON of moisture. Probably to the point of saturating the desiccant in the accumulator. I would either do the quick and dirty r134a charge, or find a container of pressurized dry nitrogen and use that to pressurize the system.
Yes and No. It all depends on how much vacuum, the temperature and how long you hold the vacuum.
After all, a pan of water will evaporate left out to stand in a room for a week or two.
Your vacuum pump pulls the existing water vapor quickly but takes longer to draw the moisture out of the desiccant and oil.
The recommended minimum time is 45 min. My bother in law (owns an AC shop) will keep the pump on all night when he installs a new system (grocery store). So it's just best to keep it evacuated as long as you can. But with new oil and new dissident, you really don't need to evacuate it that long.
http://www.youtube.com/watch?v=_laMB4H0Y_s
I ran the pump for just over an hour. The gauge read almost -29 in. Hg. when I shut off the lines then turned off the pump at about 3:45pm.
I will check the gauge again in the morning, and if all looks good, I will pull vacuum on it again just to be safe, while I look for the wiring for the low-pressure switch and wire in the high-pressure switch. Steve tucked that wiring away somewhere and I can't find it...