Yes, precision measurements would work. Looking for the length and diameter of the shaft that seats inside the hub nut, the with and depth of the groove for the circlip, and the diameter of the circlip itself. Thanks!
Printable View
Well as usual, now that I need it for something I can't locate it. Funny thing is I ran across it while reorganizing the garage 6 mo ago. Dang it !
Sorry about that.
Its all good.
In other news, here are some of the completed number characters...
Attachment 8927 Attachment 8930 Attachment 8926 Attachment 8929 Attachment 8928
And of course after looking at them all lined up right now, I may need to make adjustments to the middle of the 3 and 8 (slightly raise upward). We'll see though.
Hope to have the rest done by the end of this week. Then next week, drawing a whole gauge...
Decided to look in one more place on hunch and found the AD this morning. I have it with me and will get you those numbers this evening.
More Numbers...
Attachment 8943 Attachment 8944 Attachment 8942
Now the 9. Not a very important number. No possible configuration other than a BTTF 95mph unit would use one. Just in case though, I tried two things...
First, I tried just flipping the 6 so the 9 is a direct mirror of it...
Attachment 8946
Then I also tried manipulating the closed loop so it would vertically be the "smaller" loop since it is the TOP loop on the 6 and 8 which is smaller than the bottom...
Attachment 8945
At first, the mirror 9 didn't look right, so I created the modified one. But now comparing the two with the other numbers, the mirror one is probably the better one. Thoughts?
All I have left now is the 4, then I can get some of the letter characters done. Here is everything so far...
Attachment 8951 Attachment 8947 Attachment 8943 Attachment 8948 Attachment 8949 Attachment 8944 Attachment 8942 Attachment 8950 Attachment 8946 Attachment 8945
Jim, check your PM's and E-mail
I like the mirrored one best as well.
I may have messed the post referencing this, but what are the numbers for and why do they need to be remade/customized?
If these are vector images I could help you make whatever you need.
All you really need to read is the first post of the thread. In short though, I'm building an electronically controlled and backlit instrument cluster. New decals need to be printed for the gauges, and there is no perfect match for the typeface used. Therefore, I'm recreating all of them by hand using high resolution scans and measurements. They are vector drawings, as will be the final layout before its handed off to the specialized printers.
Thanks for the offer to help, but I'm almost done. :rock_on:
Finished the 4. All numeral characters for the cluster are complete. They are all based off of the speedometer and tachometer numbers. All secondary numbers (kph and small gauges) use identical typeface just scaled smaller.
Quick summary...
All characters are 3mm wide by 5.6mm tall. Exceptions are the 1, which is 1.6mm wide, and the 4, which is 3.5mm wide. Majority of the line widths are approximately .8mm with several exceptions. The radii used on the 0 does NOT completely match the other character's radii, but is close. The vertical portion of the 0 is perfectly strait with no radii, and all other characters have a very slight radii in most of their vertical portions. Characters with dual loops (3,5,6,8 ) have a larger radii on the bottom loop than the top loop. The 5 and 6 have a much larger bottom radii than the bottom of the 3 and 8. The 9 does not exist on any OEM design, 85mph, 140mph, or metric.
I will now work on drawing out all the letters. MPH, km/h, RPM/100, VOLTS, TEMP, OIL, FUEL.
If anyone has high resolution pictures or vector graphics of the common automotive icons for Battery, Temp, Oil, and Fuel; it would be very helpful. I'm not looking forward to drawing those especially since they exist identically everywhere. There must be a good source for them.
The final lineup....
Attachment 8968 Attachment 8969 Attachment 8970 Attachment 8971 Attachment 8967 Attachment 8972 Attachment 8973 Attachment 8974 Attachment 8975 Attachment 8976
Attachment 9311 Attachment 9313 Attachment 9310
And then some...
Attachment 9312
After struggling with the P, then realizing it matches some skewed angles of the 0, nearly everything I need for the speedometer is done. As you can see I've also started on the actual speedo itself. Only have the easy bits right now though, as I've previously measured these dimensions they were easy to draw. Perhaps slightly more difficult will be all the angled hash-marks on their exact angle and position, but I don't foresee too much difficulty. Of course there is no "outline" on the speedo face right now, and as the colors are inverted its hard to tell exactly where the borders are. You could highlight the image though if you need a basic idea. When I get it completed I'll have all the colors proper so it'll look exactly like a DeLorean speedometer.
Something that I was thinking about working on is an LCD replacement to go where the clock and rheostat are located. Its purpose would be like on a modern car display information such as door status, Avg. MPG, Inst. MPG, Check Engine, Cruise Control Output, Outside Temp, Maybe Compass, etc... I love your progress and cant wait to see your prototype at DCS! I havent fully decided about my project yet, although It would be a good addition to your cluster. In my opinion anyway lol. What's everyones thoughts on the LCD?
Davidrucker11387
DeLoDave, 6410
OLEDs are nice but sometimes hard to come by in the size format that I would like. Also if going the trouble of OLED I would want full color instead of 1 or 2 color formats like they are commonly available. The '84 Chrysler Laser is where my inspiration has come from so far on the LCD screen idea and I too was thinking on going with a digital dash but more on the lines of its obvious that its digital and not looks stock but works digitally also like the laser. I attached a picture for those of you that havent seen those cars.
If you want that kind of digital dash, it's sort of already been done using gauges from Dakota Digital.
Attachment 9486
First render of a speedometer. Few nuances still remaining...
Most of the angles between ticks on the stock speedo are about 16º. However there are a few that are 15º and 14º. This variability will be too difficult to manage with my basic software for the needle. Therefore I have decided to make them all 16º. This results in the 5mph tick being a little too close to the trip rest opening. Unfortunately that opening is a fixed location, as the new shaft will need to be in the exact same spot to clear the cluster lens.
The stock speedo is biased about 2º counter clockwise. I have recreated that here, but I may keep it strait on the final product. This will allow for better 5mph placement and better overall aesthetics.
As is obiously noticeable, the km/h ticks are not here yet, perhaps tomorrow. I still need to draw a lowercase k, m, and h. With time running out I may omit that on the initial prototype prints.
The prototype I hope to bring to DCS will be an 85mph speedometer. But the final product will still be available as 140mph or all metric (240kph).
I will soon also be placing an order for a temp sender and oil pressure sender so I can use them as a measurement base without sacrificing my own car. I will be back to PIC programming soon now.
Also just today I ordered a mid 80's Saab 900 fuel level sender. As I understand it this is a direct fit for our tank but with different connectors and perhaps no low fuel light switch. Also I believe this sender reverses the variable resistance from what the stock gauge needs to read (reverse full and empty). As I understand this is the fuel sender which TankZilla used. The new cluster will be able to operate on both this unit and stock style units, user selectable so you can change it out whenever you need to.
Got the Saab fuel level sender today. This unit will fit inside the stock location for the OEM level sender. It reads in reverse of the OEM unit, so it is not a drop-in replacement for those without a good unit right now. I got this for two reasons, first is to have a benchtop unit for testing with the new cluster. And second is to eventually replace my original sender (still working mostly fine after 120k+ miles!). Since the new cluster will operate strictly off of logic, it is a relatively simple manner to create two programs which will operate in normal or reverse. User selectable! So the fuel gauge will work on original senders, and all DMCH reproduction senders, including the new all-in-one unit with the new fuel pump.
Attachment 9641
In addition to that, I've been reading quite a few reports lately about people having problems with their TankZilla units. It also seems that most all of the problems are with the adapter box associated with it, NOT the unit itself, which I do believe is the exact unit I just purchased. Therefore people with TankZillas will be able to bypass their adapter boxes if they wish and run their sender directly with this new cluster.
A junk yard would not be a reliable way to procure 100+ chips for producing the cluster in numbers. If I was just doing for myself then yes.
I have found alternatives to using this chip so it fortunately is no longer necessary. I'm just driving it strait off the PIC. A little extra programming never hurt anyone right? :D
Considering that there is a program out there to allow a TRS-80 Model 100 to read an SD card, I'd say you're right about that! :)
Yesterday, I was under my dashboard doing some electrical stuff and found myself looking up at the underside of my gauge cluster. I immediately started thinking about this project. :lol:
I have not yet cut into this discussion, however I'm very impressed with what I read and see.
On DMCNews Hervey mentioned soon having a new unit that combines fuel pump and fuel sender into one unit.
You may want to consider and contact him for details enabling you to incorporate another improvement into your project.
Welmoed.
If I could give you pricing right now I would. Just too many uncertainties still. Biggest factors will the the parts costs for stuff I need to have made for me. New cluster housing, new fascia, new needles, and perhaps more. Right now a whole new old stock cluster from DMC costs $328.13, or $578.13 for the metric one. It will be above those numbers, but I still have no idea how much higher.
Nothing majorly new to report. I'm working on the vector graphics for the other gauges right now. Even if I cannot complete a working prototype by DCS I'd still like to have some sample decals printed up to bring with, and perhaps one or two example gauges showing how they will work.
I've also recently purchased from DMCMW a new left front hub nut and retaining ring. The idea here is I'll attach the new speed sensor in the same fashion that the angle drive is attached. Then I can quickly swap it onto my car once its ready to real road testing. This will also be how the part is provided with the new cluster.
I've also purchased an engine water temp sensor for the temp gauge. I will use this to calibrate the temp gauge function.
I'm also now working on basic circuit design layout for each individual function. Once proven out individually for the prototype, they will be combined for the final design.
While it may still be at least a year before these can be sold, I may be looking to have a few real-world test mules installed into cars across different parts of the country by the end of this year. These will need to be heavily used cars in all weather conditions. More info on this after I have the first working prototype.
One small suggestion:
When designing fonts, it is standard to slightly increase the size of characters with curved tops or bottoms and make them extend slightly higher and/or lower than the characters with flat tops/bottoms. So, for example, the numeral "0" should actually extend slightly below the baseline and be slightly taller than, say, the numeral "1". This is called "overshoot" and is done to compensate for an optical illusion that makes the curved edges look like they are not properly lined up. The usual overshoot is about 1.5%. You can read about it here:
http://www.typographydeconstructed.com/baseline/
As soon as I have a/c again I plan to drive my car in all kinds of weather. I will also be re-doing my console and kneepads in the future and that would be a good time for me to install a new cluster. If you need a test mule in a hot and humid area of the U.S., let me know... otherwise I look forward to watching the progress continue to unfold here. :)
Anything new?
Currently getting quotes for the decal printing, and to also have one hopefully printed up before DCS. Unfortunately there will not be a complete prototype ready for DCS. If I can get a prototype decal printed before DCS I will rig it up with some lights to give a good impression of the backlighting for people to see at the show. I'll also have all of my bits and pieces with for people to see the replacement for the angle drive, etc.
Work on my own car is taking up too much time to get everything else I wanted done. But oh well. I will be selling them for sure at DCS '14.
Been quickly finishing the vector images for the gauge faces. What I'm doing now is NOT final. There may be tweaking of positioning still happening. I also will further refine the characters to reflect the 1.5% baseline extension on the curved characters. Right now I'm just quickly finishing what I can so I can get accurate printing quotes and still hopefully a prototype printed before DCS.
Here is a Speedometer and Tachometer. I have now removed the 2º CCW shift the stock speedo has.
Attachment 10353 Attachment 10354
those look great, jim! :thumbup:
Who would have thought finding a high resolution image or vector image of the STANDARD International Automotive Fuel Gauge symbol would be so hard?
Well it is. So I have to make my own. Spent less than an hour making the gauge, including the characters for FUEL. Then the entire rest of the evening drawing out the fuel icon by hand. I do think though the results speak for themselves....
Attachment 10358
"UNLEADED FUEL ONLY" will follow later for the final prints. Since its an irrelevant statement these days, perhaps I'll have an option to omit it. I know the metric cluster has the bottom segment in red, does it still carry the Unleaded text?