Farrar's car blog

You guys should exchange phone numbers....

Quote:

---

Originally Posted by Farrar

I am still not sure what I am going to do about my exhaust -- Houston's headers flow better so I would like to keep them, but they are beginning to rust, besides I am not sure they could be used for two mufflers because of their length. I will have to make some careful measurements the next time I have the car in the air. That work is a very long way off -- first vacuum leak, then air conditioning.

Farrar

---

Quote:

---

Originally Posted by stevedmc

Oh crap. I forgot about that. Well you better upgrade to Spec .01 by Saturday.

---

Quote:

---

Originally Posted by Farrar

In your case, yes... because you don't have a big muffler in the way like I do! On my car, I doubt I could get a wrench in there with sufficient torque to get the nut off. I was hoping I wouldn't have to get the timing cover off until I switched to dual exhaust...

Farrar

---

Quote:

---

Originally Posted by stevedmc

Shoot, it looks like I was wrong. A quick search of Autozone.com indicated it is no longer available. You could get the gaskets from Rock Auto though. They ship pretty dang quick.

Edit: I posted this too soon. Disregard what I said.


The timing cover gasket is a piece of cake once you get the crankshaft pulley off. We could do that for you Saturday as long as the nut easily comes off.

---

Quote:

---

Originally Posted by Farrar

No, it's the timing cover gasket -- too low to be the valve cover gaskets.

I have all three gaskets but haven't installed them yet.

Farrar

---

Quote:

---

Originally Posted by stevedmc

We can easily fix your oil leak if is due to a bad valve cover gasket.

Part # VS26090 is available from Autozone. They may have to special order it but if you go in the store today they should be able to have it for you by Friday. I ordered my set from Rock Auto and it was about $12.

It shouldn't take more than an hour to do the work and it would make a nice tech session repair.

---

Quote:

---

Originally Posted by Farrar

Oh, man, I forgot all about that!

Well, if I do have a vacuum leak around the intake manifold there is little I can do about it -- I put fresh O-rings under the manifold and tightened down the intake manifold's bolts as tight as I dare (the heads started rounding off). And don't forget, my oil leak is back so every time I drive the car it collects oil in the engine valley.

I have a gig Friday night (see video) but it should be over with by 10pm, which means I may be able to get a decent amount of sleep before Saturday morning's shin-dig.

http://www.youtube.com/watch?v=WdgXM6MSWMY

Farrar

---

Quote:

---

Originally Posted by stevedmc

Bill would be proud. You better fix that car soon. Our little shin dig is this Saturday.

If it makes you feel any better I am currently without AC as well. I messed up my crankshaft pulley pretty bad when I was taking off the nut that holds it. Fortunately the part that runs the water pump and alternator is fine but the AC section is whop sided like the tire on my bike.

---

Quote:

---

Originally Posted by Farrar

I used to smoke a pipe. I still have two pipes at home, but I haven't done anything with them in a while. They're probably no good anyway, but they do look pretty.

I bought a 99¢ cigar yesterday afternoon, so I am all set to do the test. I will remove the carburetor and seal the top of the intake manifold with duct tape, then cap off one of the manifold vacuum ports and stick a long hose on the other. After that I will be ready to do the test. All I need to do is find the time to do it, which is difficult this time of year.

I really do wish I could drive the car right now; when I walked out of the apartment this morning to go to work it was 68°F with low humidity -- perfect window-open driving weather, no need for air conditioning.

Farrar

---

Quote:

---

Originally Posted by sean

You guys should exchange phone numbers....

---

This thread is public so that anyone can jump in with a comment at any time. (Case in point: your post above.) Just because there are only two people engaged in a discussion for a few minutes does not make it a private discussion.

Other people have said in the past that they read this thread while not necessarily posting in it, and I assume they were not lying to me, so I will continue to keep the discussion open since nothing of a sensitive nature has been thus herein discussed, nor is any such information likely to be disclosed in such a public forum.

Unless you were just trying to be funny, in which case :lol:

Farrar

Quote:

---

Originally Posted by Farrar

Unless you were just trying to be funny, in which case :lol:

---

lol....let's not forget one learns quickly to be very careful when offering a room around Steve.

Quote:

---

Originally Posted by Ron

lol....let's not forget one learns quickly to be very careful when offering a room around Steve.

---

Or asks him to remove a main pulley nut. :biggrin:

Would anyone be interested in sharing a room with me for DCS?

Quote:

---

Originally Posted by stevedmc

Would anyone be interested in sharing a room with me for DCS?

---

If I didn't have the family coming with I'd do it.
Attachment 5951

Quote:

---

Originally Posted by sean

Or asks him to remove a main pulley nut. :biggrin:

---

One has to be willing to overlook certain accidental double-entendres; for example, I once knew a young bass player who broke his nut while adjusting the G string. In the proper context, I was able to listen to his tale of woe with proper seriousness.

Farrar

Quote:

---

Originally Posted by Farrar

, I once knew a young bass player who broke his nut while adjusting the G string.

---

Farrar FTW!

Quote:

---

Originally Posted by Farrar

I once knew a young bass player who broke his nut while adjusting the G string.

---

Now wait a second!...I can see this the other way around, ie breaking a G string while adjusting a nut, in either sense, but...

Quote:

---

Originally Posted by Ron

Now wait a second!...I can see this the other way around, ie breaking a G string while adjusting a nut, in either sense, but...

---

The nut on an instrument of the viol family is that small light-colored piece or plastic/ivory at the very top of the fingerboard. It has indentations in it to help hold the strings in place. If your instrument is cheap or badly-maintained (and his was) it is possible to break the nut at one of those indentations as they are naturally that piece's weak spots.

Back on topic: found out that the small cigar I bought at the gas station is grape-flavored. Ew! I am glad I don't need to smoke it for very long to do my test.

Farrar