Don't feel too bad...it also supplies power to illuminate the instrument panel (5 bulbs), license plate (2), cigar lighter, itself, and clock (early).
Printable View
It just occurred to me that it would be far easier to hang the skirt from the body of the car itself. DOH! Now if only I hadn't drilled those holes in the spare tire well access cover! Oh, well -- it was already broken in several places. I can either buy another one from Houston, or use it to teach myself fiberglass repair. :)
Farrar
I think you will find initial installation and later maintenance easier if you attach the splash guard to the removable panel.
The splash guard does not drop straight down -- it angles rearward behind the pump boot:
Attachment 4042
That's why my rubber was cut too short -- I measured straight down. One of these days I hope to replace it with a piece that is the correct length.
Bill Robertson
#5939
Hm, my splash guard is ten inches tall and the entire length of the access panel. Maybe I made mine too big! I will have some time to experiment later this week.
Farrar
I really hate those pump covers, so I will avoid using one if possible. For now, I will see if I can use a belt or suspenders, instead of both.
Farrar
You can't run the full width of the access cover, otherwise the guard won't clear the heater core hoses.
Mine is 8.125" tall (with the Gorilla Tape extension) and 14.125" wide:
Pump covers suck. They are a PITA to install, they shrink with time, and they crack. I think you'll be very pleased with a splash guard. Even after driving to Virginia Beach in the rain, the next day I only had a couple of drops of water in the boot when I took the pump out to show someone my tuna baffle.
Remember that most aftermarket fuel pumps are designed to be frame mounted:
Attachment 4043
In such a location they are exposed to far more water than they will ever see in a DeLorean pump boot.
Lotus could have saved us all a lot of trouble if they had just put the plenum drain at the outside edge, next to the fender (as the Ford Truck Division does, thank you very much).
Bill Robertson
#5939
Driving in the rain hitting a huge water puddle, driving over dirt patches or roads, general air moisture. Do as you wish Farrar but as poorly engineered as the car was I think covering the fuel pump is worthwhile long term. Of course at the rate you guys are replacing pumps I suppose long term is not an issue. It amazes me how resistant you are to an ounce of prevention here. If its a matter of not wanting to spend the money on a cover, fine, then cover that cat with some gorilla tape.
Aftermarket pumps are designed to be frame mounted (ie: exposed to huge water puddles, dirt patches, general air moisture, etc). Please try again.
Ford truck fuel pumps (electric) are mounted to the frame from the factory.
Attachment 4044
(As you can clearly see, they are also designed for road salt exposure -- this truck came out of New Jersey).
Bill Robertson
#5939
May I humbly suggest that you try to work smarter, not harder. It might make you a more pleasant person.
Bill Robertson
#5939
It's not mere exposure to water -- it's the fact that the top of the fuel pump is lower than the top of the boot and the boot is sealed against fuel leaks. Because of this setup, water, once it has arrived, has no way to drain out.
I am going to consider covering the pump, but I have to perform a test first. I will install my own water guard, and then pour a bunch of water over the hood and windshield. Then I will look at the pump to see how wet it is. If I need a cover, I will seek something more permanent than a rubber cap (which will shrink in hot weather as New Orleans has for 9 months out of the year) -- for example, a plastic cap with a rubber grommet in the middle for the fuel hose to poke through.
Farrar
Ignore Sean. I know three owners running splash guards, and all of us are quite happy with them.
I think your pump problems are caused by poor grounding. Notice you suffer motor failures, not bearing or vane failures. I would try grounding the pump directly to the frame and see if that doesn't work better (assuming your crappy braided strap at the motor mount is still halfway usable).
Bill Robertson
#5939
I have a second engine block ground which you installed for me after the fire (back when we thought it was electrically-caused). As for better grounding of the pump, I may try seeking a better ground for the inertia switch as I don't think I want to lose that safety feature.
Farrar
There are quite a few DeLoreans with melted inertia switch connectors, #5939 among them -- I don't think the damn things are grounded worth 2 cents.
Bill Robertson
#5939
Sounds like a good addition to my ground bus.
Now we'll switch gears entirely and enter the realm of the hypothetical.
[insert spooky music here...]
I found something else I want to do in the future: install a time-delay relay on the power window circuit. I am sick and tired of turning the car off and taking the key out, only to discover that I left the windows down for the Nth time and I have to put the key back in and turn it on in order to roll up the windows again. :lol:
Farrar
The Blue/White junction is right next to the door lock circuit breaker -- just cut the windows loose from the junction and reconnect them to the circuit breaker (live all the time). You would only need to add an inch or two of wire.
Nevermind: the windows are Green/White. You can still use the circuit breaker (or any other protection that tickles your fancy), but you'd need to cut the windows loose under the console (that's where the Green/White junction is).
Bill Robertson
#5939
I was actually planning on adding a relay to the power window circuit anyway, in advance of my re-doing the center console armrest -- and, in the process, replacing the stock window switches with different ones. The reason for this is that the window switches I bought have a relatively low amperage rating.
I will post a schematic of my future power window circuit later.
Farrar
Actually, I checked the switches and they're rated for 10 amps at 12v DC, so that should be fine. No relays to add except the delay relay. Using this guide as a ... er .. guide, I came up with this:
Attachment 4048
I'm no electrician, so someone please correct me if I've made a mistake here.
Thanks,
Farrar
I also made this for the cooling fan circuit. However, I forgot to label the relay terminals. They should be self-explanatory, but for reference they are:
top: 86
left: 30
right: 87
bottom: 85 and 87A.
I have just discovered OpenOffice "Draw." Hooray for being able to draw straight lines without a ruler! (I can never find my ruler.) :D
Farrar
I think I found a place to get my alignment done... Not too far from my new apartment, I found an honest-to-goodness alignment shop -- yep, that's all they do! And judging from the look of their shop, they still do things the old-fashioned way. How nice it would be to not have someone saying "Well, your car's not in the computer..."
Farrar
Its for as long as I own the car and isn't transferable hence needing to swap vin tags. I paid $180 including taxes, fees, and whatever other nickel and diming they could think of.
I verified with the manager that it is for the life of the car, as often as I want, no mileage limits, and absolutely no future cost including shop fees. Considering that an alignment cost $80 I think I got a pretty good deal. As long as Firestone doesn't go bankrupt I am all set.
When I get around to replacing one of my rear shocks (long story) I am going to bring the thing in again for another alignment.
Thanks, Ron! I will sketch something up and see if it works.
In other news, I can't use my new fuel pump yet, because there's a coupling stuck in the bottom of the fuel pump carrier which I can't remove. Bill Robertson must have the best thread-lock compound on the planet...
It will have to wait until Sunday.
Farrar
You mean like this?
Attachment 4197
Farrar
That would work, but the load is still going through the delay module. Actually, that's how the switched line coming in is stock (but feeds a lot of things). They should add "Enable" to their relay...it got me too. lol
I'd try this:
Attachment 4205