:hmm: it has already been used successfully in a 369 by at least one owner in the UK, and having driven his car I know it drives a lot better with the uprated parts. As Nick mentioned though the...
Type: Posts; User: MikeWard
:hmm: it has already been used successfully in a 369 by at least one owner in the UK, and having driven his car I know it drives a lot better with the uprated parts. As Nick mentioned though the...
Increased horsepower? Dyno graphs please.
It might be worth checking with GTO Racing in the UK, I believe they sell an uprated input shaft.
https://www.gtoracing.co.uk
Autosparks make those connectors brand new.
If they don't currently have enough in stock, perhaps try contacting them to obtain pricing/timeline for the quantity you require....
Using a couple of piggyback crimps pickup the +12v from the glove box light, and the switched earth at the blue diode behind the hvac panel.
65288
Fair enough.
I was going from the Lotus recommended spec for the UN1 gearbox, which is 75w90 GL-5 fully synthetic. It works well for me.
Side note Castrol TAF-X has long since been...
Why not? Just curious as I've run Castrol TAF-X 75w90 fully synthetic in mine since mid 2012, 8 years on and 20k+ miles later and haven't had any ill effects from using it.
He is probably too busy 'reacting' to his own posts on Facebook/Instagram to be able to respond to you.
As Chris said, the Amsteer joints are the only ones to use. It really isn't worth taking a risk on such a safety critical part by using the cheaper alternatives. The Amsteer joints are tried and...
I would suggest following this guide on checking correct routing of the vac pipes (without the need to remove the manifold):
http://www.deloreaneurotec.uk/viewtopic.php?f=17&t=4619&p=61868
...
As dmcnc said, the original seat covers did have ruching in the leather. See this clip from 1981 at around the 1 minute mark. https://youtu.be/kZo8d-z4iCM?t=58
Possibly Renault 19?
https://www.ebay.co.uk/itm/303126120197
The info in that topic has been superseded, check this topic: http://www.deloreaneurotec.uk/viewtopic.php?f=17&t=5937#p78083
Correct.
If you use the B28E fuel distributor the frequency valve and piping, and WOT switch are removed from the equation as they are not used, along with the lambda system.
DeLoreanGo stock fully refurbished control pressure/warm up regulators: https://www.deloreango.com/us/control-pressure-regulator-warm-up-regulator.html - professionally rebuilt by Ken Mills Injection...
I would suggest fitting the entire set of B28E Volvo fuelling/igntiion parts if you want to get the best benefit out of it - including the fuel distributor which get's rid of the frequency...
Here are the current UK regs on the rear fog light requirement.
The modification doesn't specifically follow those regs in that it converts two lamps to function as rear fog lights, however for...
:rofl::aniclap::aniclap:
Agreed, I had my car on a dyno a number of years ago and performed a back-to-back test running standard filter vs a K&N filter. There was literally zero difference to power output between the two...
Ah I see what you mean.
I'm sure if someone was to take the time to remove that part, take measurements of the i/d, o/d and thickness of the o-ring and then get in touch with Arran at DeLoreanGo...
If we're talking about the same o-ring then I believe it is the o-ring at the end of the pressure regulator assembly (circled below) which is responsible for sealing off the flow when the engine is...
The CPR should have a fine mesh filter.
59984
Unfortunately (and particularly on American rebuilt units) it is typical to see the original filter swapped out for a sintered style brass filter. I...
That's interesting. I can't say I have ever see the type shown on the left in that picture, and I've shimmed a fair few PPR's over the years, they have always been the type shown on the right. What...
It's certainly worth retesting with the vac pipes disconnected, plugged and electrical connection disconnected.
I had a quick look and it appears that the 076 distributor is from a Volvo 260.
...
The shims only affect primary pressure, they should have zero impact on control pressure, if it does then something else is up. 70PSI is way out for control pressure - as Ron noted it should be a...