Search:

New LED Headlights

Truck-Lite has developed new headlights, in the past they had a set that looked strange and didn't deliver the projection needed for an efficient headlight.

The new...

Hi Brandon,

Thanks so much for organizing our last tech day, it was indeed a very good turnout.

Please sign me up for the upcoming one, if you can use any assistance please let me know.
...

Dave, indeed it doesn't have the valve. While filling I watched carefully not to overfill according to the bottle gauge. However it still popped.

Dyno :-)

The engine is modified to a stage III with:

Don's Crazy Cams and Hervey's Headers, magnaflow exhausts, modified intakes and exhaust ports.

Here is a write-up of the original...

Yes, unfortunately after I rebuilt the engine to the last bolt and nut (running better than new with I might say 239 HP non turbo), rebuilt the breaks to the last piston, all electrical, new...

In replacing A/C lines, it's important to hookup high and low correctly to the compressor.

43622

Unfortunately that also took-out half the evaporator box. So having to replace the box and...

Thanks for all that have contributed.

I'm testing to see where it runs best and will post an update when I've had the best results.

On a side note. I also had start and cutoff issues. The...

According to my paperwork it was sold (by Dave) to the previous owner in Dec of 2013 and I bought it from him in March of Last year.

The car does come with some incredible paperwork, originating...

excerpt from : http://www.projectvixen.com/dmcnews-archive/msg79587.html

High Performance Cam Shafts (I call them "Don's Crazy Cams")
developed by Don Steger from DeLorean Motor Company -...

Excellent. Thanks so much for that tip.

I followed your instructions very carefully from :

http://www.dmctoday.com/showthread.php?97-Ford-Duraspark-Ignition/page7

41090

Got the duraspark at a local autozone, The harness /...

David, I read about that. The coil that was in the car is a MSD 2 HEI coil (according to spec it doesn't need the resistor, it's actually supposed to perform better at higher voltages)
...

Bill, very good point. I was also in the process of checking that. Thanks for the suggestion.

It turns over, but wont start. Using a jumper I can get it started after several tries. then it runs good. The starting spark is orange. running I dont know.

Battery is brand new (optima yellow top deep cycle) . Its fully charged.

I'll check the cold start injector and post an update.

Spark plugs are dry and light brown/tan. The spark is orange, so not good) I haven't tried the fluid.

I can get it started using a jumper cable with a second car. Once it's run I can usually start...

Hi Bill, I performed the tests the k-jet gurus mention, switching the plugs. Checking injectors. Checked all vacuum lines. Spark gaps, valve timing, compression test (dry and wet). All seem good.
...

I'm looking is someone might know the correct timing for Don's Crazy cams. I read in an article it should be :

"When running Don's Crazy Cams, adjust your timing from 13 degrees to 20 degrees."
...

That sounds perfect. Thanks


Sent from my iPhone using Tapatalk

Hi Ryan,

I tried that and tried the old strut again just to see. Both result in the same issue. It may open more than halfway , but have to help it the rest of the way. It will stay open once...

I have the pj Grady lift Pistons


Sent from my iPhone using Tapatalk

Hi Brandon,

Thanks so much for the offer. Lets plan on getting together once Nick is back.

Nick, can you let us know when you're back to plan a day.

Guys, Thanks so much

Maurice

Hello,

My divers side door is only opening halfway (I have a new spring), so I believe my torsion bar needs adjustment. I've read up on it and saw a YouTube video on it. It doesn't look to...

Hi Spittybug, thanks for the word of caution. The battery has been replaced and I'm in the process of replacing all the relays / fuses etc. Unfortunatly the damage has been done in the past, so...

Of all parts that have gone bad, my fuse box mounting tray is fully rusted and rotted away.

The part I'm looking for is:

http://www.deloreanindustries.com/26-mounting-tray-lh/...