On my car, the spark plugs look great in fact much the same as your most recent photo, however one exhaust manifold and cat is a bit hotter than the other side. can't remember which at the moment but...
Type: Posts; User: 82DMC12
On my car, the spark plugs look great in fact much the same as your most recent photo, however one exhaust manifold and cat is a bit hotter than the other side. can't remember which at the moment but...
I have the same kit. Sure looks slick and it's easy to install. However a couple years later I remain somewhat unconvinced that you get the same brake pressure with this system as opposed to mostly...
Yeah a couple years ago I replaced the cowl and added a stainless intake screen. Seems like cheap insurance if nothing else. The cowl is kind of a pain to remove, needing to remove a few screws that...
That would be ideal but maybe even only a 2" hole would be fine
Sent from my Pixel 6a using Tapatalk
Now that you have the HVAC box out, I would love to know if it is possible to cut a rectangular hole In the face of the box facing the passenger seat vertically above the drain tube somewhere so that...
I'm getting ready to take this car on a 9 hour trip in a couple of weeks so I've been driving it as much as I can to shake out any final issues, and fortunately nothing has popped up. I did the same...
The wiring for the cigar lighter is ridiculous. I used to blow that fuse and the bulb most of the time when I removed the center console. Hard to see what you're doing in there when reinstalling...
Same thing, it cannot be done the way you were trying to do it. Have you priced out how much a new rear window costs?
Sent from my Pixel 6a using Tapatalk
These two marks indicate how much twist remains in the bar at the show door position. The door would have to be far beyond vertical to remove the bar without the spline plate. It's possible the bars...
I'm sure you had assistance to make sure the door didn't tip over backwards on the roof and disconnected the wire harness first? I was not interested in testing that limit and certainly would not...
Also, OP, are you seriously trying to remove the torsion bar with the gas strut in place?
Sent from my Pixel 6a using Tapatalk
Have you actually done this? I tried this urban legend myself while having my T panel off and it's not true. There remains too much twist, vertical is nowhere near enough, it would have to be...
Well you're about 2 minutes from smashing your rear window and denting the T-panel, and possibly injuring yourself. That foam won't do shit.
Your problem is you have not relieved the tension on...
Honestly I would probably be so disheartened I would buy something completely different. That's the truth.
Sent from my Pixel 6a using Tapatalk
Yeah I do worry. I've had close calls before and maybe someday it won't be my lucky day. I try to avoid certain areas, driving at night, avoiding bad weather, and drive very defensively. I will...
Good question! I guess everything I do to this car is a labor of love so to me I'm glad it's the best it can be. My old mounts were not bent from the outside looking at them but once I had them out...
I had to do a couple of minor adjustments to the passenger door striker but otherwise at this point the car was done. It was filthy from all this work all winter so I drove it out the driveway to...
At this point, all that was left was to install the T panel and weather stripping. Even after all of this work, I still had a tough time getting the T panel aligned and set exactly where it needs to...
The next job was to install a new set of rear upper infill panels which is what the T-panel attaches to on the rear inside. I had to remove the first set of panels because I found the M6 screws that...
Next I received my windshield side trim pieces from the power coat company (Thanks Eric Woltkamp in FL!). These were a pair of NOS side trim pieces that I had shipped directly to Eric so his company...
OK I just realized I'm about a month behind on this blog!
In early April I took delivery of my refinished dash from David Hudgins (see my review in the vendor /product reviews section) which...
Good to know. I will try the micro edge blades first since that's what I have on order but if they give me trouble I will try a silicone. One of the vendors was telling me Deloreans are especially...
I've had a wiper blade chattering problem for a while. I had Bosch icon blades for a really long time and I think they were pretty good. Then I switched to some beam type wipers which never got much...
I have the DPI Delphi pump and the stud is a non-issue. it sits under the pump in a sort of recess if I recall.
I know he has a busted up binnacle he's going to try to work on but he told me there are some technical challenges. Not sure if it can be done this way.