FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    17
    Views
    582

    [Electrical] I don't think the problem with OEM socket is not...

    I don't think the problem with OEM socket is not deep enough but it had a larger diameter and the current power plugs don't hold very well.
  2. Replies
    20
    Views
    377

    [Suspension] Did you tighten the LCAs with them not extended? ...

    Did you tighten the LCAs with them not extended? With stock bushings you need to tighten them at normal extension.
  3. Replies
    24
    Views
    1,293

    [Engine] Rod and Main bearings are made with soft...

    Rod and Main bearings are made with soft surfaces. In the old days you could repair the Babbitt bearings.
  4. Replies
    17
    Views
    582

    [Electrical] You will want to replace the lighter if you plan...

    You will want to replace the lighter if you plan to use it to power or charge anything. The OEM lighter was not a standard size.
  5. Replies
    18
    Views
    2,102

    [General] When was the two key system stopped. I'm not...

    When was the two key system stopped. I'm not sure if my car had new one key locks installed before I bought my car.
  6. Replies
    8
    Views
    405

    I think black center caps would set it off. ...

    I think black center caps would set it off. Could probably 3D print some with a logo of your liking.
  7. Replies
    8
    Views
    405

    I kind of like them. It would take some time to...

    I kind of like them. It would take some time to get use to them. New cars these days are using higher spoke counts so it's a big change only seeing 6 double spokes. My Camry has 10 spokes.
  8. Replies
    11
    Views
    487

    [Electrical] Carfully clean the silver wire with a scotch...

    Carfully clean the silver wire with a scotch brite pad.
  9. Replies
    11
    Views
    487

    [Electrical] You should pull your fuel sender and manually...

    You should pull your fuel sender and manually move the float to see if you have any dead spots. You may just need to clean the resistance wire on the sender.
  10. Replies
    17
    Views
    688

    [Electrical] The black box with the two connectors is the idle...

    The black box with the two connectors is the idle ECU. The silver box mounted vertical is the lambda ECU. The ignition ECU is mounted under the metal plate and is gray.
  11. Replies
    11
    Views
    500

    [Electrical] When you shut the door it vibrates the bad...

    When you shut the door it vibrates the bad connection. My bet is the feed through bolts at the back of the relay compartment are not tight.
  12. Replies
    33
    Views
    912

    [Engine] When you unplug the WUR connector it takes a long...

    When you unplug the WUR connector it takes a long time for it to go into normal mode. When cold your mixture is very rich.

    So it looks like your engine is running better with the rich mixture...
  13. [General] Some cars with the OE RPM relay will prime when...

    Some cars with the OE RPM relay will prime when the key is turned on. Some won't. The OE RPM relay can pick up an ignition pulse when the key is turned on and that would make it prime. My RPM...
  14. Replies
    7
    Views
    386

    I also have a MIG. It's nice to weld with one...

    I also have a MIG. It's nice to weld with one hand and very fast for a long weld. Making spot welds to hold things in place is also useful. I do have an electrical spot welder also but don't use...
  15. [Fuel] You would need the mating electrical connector. ...

    You would need the mating electrical connector. The quick connect fittings for the fuel pump (outlet and return). Some extra hose if yours is to short. And fuel injection hose clamps for that hose....
  16. Replies
    5
    Views
    283

    [Transmission 5-Speed] The paper gaskets require perfect mating...

    The paper gaskets require perfect mating surfaces. If it's not a critical dimension, I cut thicker gaskets. For the W pipe I did that and used a sealer on one side but left the other side dry so...
  17. [Fuel] Because our tank has a very small rib on the pump...

    Because our tank has a very small rib on the pump hole, The V clamp does not pull the pump down tight. It just holds it where you push is down. I thought about machining the proper shaped ring to...
  18. [General] Yes you need a mechanic that knows our car. The...

    Yes you need a mechanic that knows our car. The fuel pump only runs when the engine is firing. It's a simple test for those in the know to jumper the RPM relay to test the fuel pump.
  19. Replies
    7
    Views
    386

    We think alike. I just thought of that when I...

    We think alike. I just thought of that when I was in the garage and saw my TIG welder. My TIG can do stick welding and adjustable amps.

    Just clamp on the cables, set the amps and throw the power...
  20. Replies
    7
    Views
    386

    I like that idea to use a battery to heat a stud....

    I like that idea to use a battery to heat a stud. Never heard of that before. I would guess most of heat would be right at the threads in the block. You got me thinking maybe a low volt heavy amp...
  21. Replies
    48
    Views
    8,340

    [General] I've seen some solid state battery relays from...

    I've seen some solid state battery relays from $150 to $500. I'm concerned about the inductive spikes from the starter causing a failure of these. But I would guess that $500 one has found a way to...
  22. [General] Most common issue is the pins on the resistor in...

    Most common issue is the pins on the resistor in the engine bay. Pull those connections off and back on.

    But there are a lot of other things it could be. First thing to determine if the problem...
  23. Replies
    8
    Views
    415

    [Electrical] Here is my thread on what I did. I think Toby is...

    Here is my thread on what I did. I think Toby is selling something similar now.

    http://dmctalk.org/showthread.php?10918-Latching-Battery-Relay
  24. [Fuel] My pump is the Bosch 67317. I got that one...

    My pump is the Bosch 67317. I got that one because the owner that convinced me to design the fuel gauge ECU also used that one. I don't know if Hervey used the same. I did do a max pressure test...
  25. Replies
    8
    Views
    415

    [Electrical] I must admit I've pulled relays without...

    I must admit I've pulled relays without disconnecting the battery but my relay pulling tool is safe for that but now that I have a battery disconnect I do use it with any electrical work.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4