FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Jonathan

Page 1 of 20 1 2 3 4

Search: Search took 0.16 seconds.

  1. Replies
    8,745
    Views
    1,866,244

    [General] Hard to simulate that one with the garden hose......

    Hard to simulate that one with the garden hose... :)
  2. Replies
    8,745
    Views
    1,866,244

    [General] I have a question about the cooling system flush...

    I have a question about the cooling system flush I am currently doing. I hadn't replaced or flushed out the coolant for a long time and even back when it got done, it was my mechanic helping so I...
  3. Replies
    13
    Views
    2,575

    [Wanted] For anyone not already realizing the obvious, I...

    For anyone not already realizing the obvious, I fixed this on my own car ages ago. And don't need to be brought in or included in the current troubleshooting.

    Normally I wouldn't even reply and...
  4. Replies
    6
    Views
    281

    And plugs into item #27, which is a long skinny...

    And plugs into item #27, which is a long skinny metal tube that goes from that rubber hose back towards the rear and runs along the driver's side of the transmission. It goes quite close to the ATF...
  5. [Engine] Thanks for that. It is a bit of an illusion. ...

    Thanks for that. It is a bit of an illusion. And hard to capture on camera. Like our eyes see it in person, but not otherwise. And the engine itself is moving a little bit too in the mounts,...
  6. [Engine] Good call on the hose, Ron. I did that last...

    Good call on the hose, Ron. I did that last night and then went for a drive. My usual lap of 40 or so miles and everything was fine. Thanks.
  7. [Engine] https://www.youtube.com/watch?v=zwYo_hbn3CQ ...

    https://www.youtube.com/watch?v=zwYo_hbn3CQ

    Does this look like a straight exhaust leak at the clamp between the catalytic convertor and the muffler? Or does it look like some PB Blaster burning...
  8. [General] The answer is YES. The answer to who can do...

    The answer is YES.

    The answer to who can do that for you is Chris Nicholson. Either you get your car to him (in the UK) or you get lucky and he comes to your car (or a shop that's coordinated him...
  9. [Engine] Got it all back together and she fired right up. ...

    Got it all back together and she fired right up. Well, not quite right away, but after a few tries. I tried to start it and it would whoomph and go and then immediately die. It did this 3-4 times...
  10. [Engine] Thanks a lot, Dave. I took it off for the time...

    Thanks a lot, Dave.

    I took it off for the time being. I happened to also buy a new boot separately and may try and wrap my head around how it is supposed to go sitting comfortably in a chair...
  11. [Engine] I'm pretty much done with installing the new...

    I'm pretty much done with installing the new replacement parts I had to do and ready to put things back together. I was hoping to get some clarification on something though as it pertains to the...
  12. Replies
    8,745
    Views
    1,866,244

    [General] Have a read through this for the brake fluid...

    Have a read through this for the brake fluid reservoir level switch: http://dmctalk.org/showthread.php?15745-Brake-fluid-reservoir-level-switch-operation-and-troubleshooting
  13. [General] The mast itself can be removed easily. It just...

    The mast itself can be removed easily. It just threads on. The base can be removed as well, but you need to fiddle with it a little because there is a claw/clamp thingy that helps keep it in place....
  14. [Engine] Thank you both. I had wondered about that...

    Thank you both. I had wondered about that reference in the manual and whether it meant it was the torque the starter generated and not the mounting bolt torque. All good. I'll go with the 27 ft lb...
  15. [Engine] Hey Dana, Do you recall what torque value you...

    Hey Dana,

    Do you recall what torque value you used on the three mounting bolts for the starter? I don't see it listed in the manual. I have the starter reinstalled, but haven't torqued down the...
  16. Replies
    8,745
    Views
    1,866,244

    [General] I'm well past the point of no return on my...

    I'm well past the point of no return on my crankshaft pulley plus other stuff work. The new pulley is in and it went pretty well. Took the fascia and muffler off as well as the alternator and...
  17. Replies
    12
    Views
    666

    [General] Front license plate should narrow down where it...

    Front license plate should narrow down where it was slightly. Not being able to read it, lol. Just that it had one.
  18. Replies
    10
    Views
    419

    [General] First thing you do is tape the edges of the...

    First thing you do is tape the edges of the stainless once you get the panels off. This will save you from going to the ER to have them sew your finger back on.

    I suspect it will be obvious what...
  19. [Engine] Making more progress. The nut came off a LOT...

    Making more progress. The nut came off a LOT easier than I expected it to. First try with the impact gun and it spun it loose. Big difference having all that other stuff out of the way and getting...
  20. [Engine] And it begins!!! Whooohoo! Call me strange, but...

    And it begins!!! Whooohoo! Call me strange, but I look at the filthy mess I now have good access to and all I can think of is how I'm going to enjoy taking my sweet time cleaning things up and...
  21. [Electrical] If you remove that fused jumper entirely, what do...

    If you remove that fused jumper entirely, what do the ends of the spade connectors look like? The reason I ask is I had one of those in my car and noticed a little melty melty, but caught it sooner...
  22. Replies
    8
    Views
    331

    [Electrical] Mine is abysmal looking too. EDIT: and upside...

    Mine is abysmal looking too. EDIT: and upside down apparently too. My computer has decided to be a dick at the moment, sorry about that.

    I don't have one right yet, but will put an order in for...
  23. Replies
    8
    Views
    331

    [Electrical] Looking back at my notes (aka LARGE spreadsheet,...

    Looking back at my notes (aka LARGE spreadsheet, lol), I got the positive cable from DMCH and the negative and jump start cable from DMC Europe. More often than not, I lump parts together in orders...
  24. Replies
    8
    Views
    331

    [Electrical] This one: ...

    This one:

    https://store.delorean.com/105162-ground-braid.html
  25. Replies
    8
    Views
    331

    [Electrical] Actually, I think I had one thing confused...

    Actually, I think I had one thing confused already. I was thinking the black cable terminated on the engine mount, but that's not right. It terminates on the trailing arm bolt bracket on the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4