FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Raphael

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    91
    Views
    20,278

    [General] I used a heatsink but it never gets really hot....

    I used a heatsink but it never gets really hot. I'm sure the module can be mounted directly on the stock ecu frame, this would offer enough surface to dissipate heat. after all, i had the same module...
  2. Replies
    91
    Views
    20,278

    [General] no, I left the rotor untouched.

    no, I left the rotor untouched.
  3. Replies
    91
    Views
    20,278

    [General] Hi I'm the author of the initial post about HEI...

    Hi
    I'm the author of the initial post about HEI modification. ( http://dmctalk.org/showthread.php?5158-HEI-ignition-conversion ). I used Pertronix's module and MSD blaster coil without ballast...
  4. in the same way, the seal from an otterstat makes...

    in the same way, the seal from an otterstat makes a perfect seal for the automatic gearbox dipstick.
    3268532686
  5. Replies
    56
    Views
    25,521

    I found a noticeable improvement on idle, low-end...

    I found a noticeable improvement on idle, low-end torque and overall driving agreement. But don't expect big horsepower gain, it's just that the ignition works at full potential now. I can open plug...
  6. Replies
    56
    Views
    25,521

    On the practical side, I've been using this setup...

    On the practical side, I've been using this setup for one year now, without ballast, and everything is working perfect
  7. Replies
    30
    Views
    7,359

    [General] Hi The"blue" one is actually in Monaco, and as I...

    Hi
    The"blue" one is actually in Monaco, and as I live in France, I gave a visit to the owner a few years ago. History of the car attests that it came this way from the factory.
  8. Replies
    21
    Views
    6,155

    [Transmission 5-Speed] I experience the same issue. The fact is the...

    I experience the same issue. The fact is the noise isn't related to RPM; it's the same whatever the gear and engine speed. in case you'd ask; YES my TOB is new, the fork pivot is greased and the...
  9. Replies
    56
    Views
    25,521

    yes , to make it simple : - to get better...

    yes , to make it simple :
    - to get better combustion, you need a better spark.
    - to get a better spark, you need to increase plug gap.
    - to increase plug gap, you need a better coil
    - if the new...
  10. Replies
    56
    Views
    25,521

    GM actually put the module on a heatsink on the...

    GM actually put the module on a heatsink on the firewall of 90's GM trucks. that's this particular heatsink I used here ( AD Delco # 10474610 ).
  11. Replies
    56
    Views
    25,521

    yes of course, my first idea was to mount it in...

    yes of course, my first idea was to mount it in place of the ballast. the only modification would be to add just one wire between the setup and the coil.
    Then I installed everything in a stock...
  12. Replies
    56
    Views
    25,521

    Blaster's primary resistance is 0.7 Ohms. I had...

    Blaster's primary resistance is 0.7 Ohms.
    I had doubts too, that the setup would withstand full voltage so I ran it with the stock ballast at first. Then I received infos from MSD's tech line...
  13. Replies
    56
    Views
    25,521

    After some hours of road test I can attest : -...

    After some hours of road test I can attest :
    - the GM module doesn't generate high temperatures. the little heatsink that I use (see pics in the first message) is just warm after hours of driving....
  14. Replies
    56
    Views
    25,521

    I just received a reply from MSD Tech support,...

    I just received a reply from MSD Tech support, they confirm that we can get rid of the ballast when using a modern module like the GM HEI.
    of course the ballast is still necessary when running the...
  15. Replies
    56
    Views
    25,521

    yes of course, in addition I already have a MSD...

    yes of course, in addition I already have a MSD Blaster II coil and running wider gap on the plugs, and 8mm wires.
    I kept the ballast resistor as long as I used the stock ECU, but now with the GM...
  16. Replies
    56
    Views
    25,521

    everything is soldered :) I just used rubber...

    everything is soldered :) I just used rubber covers instead of shrink sleeves, over the solders
  17. Replies
    56
    Views
    25,521

    mine was turning bad slowly. it was still working...

    mine was turning bad slowly. it was still working ,but would miss sparks randomly, and crash passed 3000 rpm.
    and here in France, we experienced a few ECU going bad, I think the electronics inside...
  18. Replies
    56
    Views
    25,521

    PIN B - to #15 : +12v ( green wire ) PIN C - to...

    PIN B - to #15 : +12v ( green wire )
    PIN C - to #16 : to coil ( white/slate)
    PIN G - to #7 : to pick-up coil ( inner blue wire )
    PIN W - to #31d : to pick-up coil ( outer black wire )
    Mounting...
  19. Replies
    56
    Views
    25,521

    here it is. no secret.:hihi: ...

    here it is. no secret.:hihi:

    http://stainless.delorean.fr/gallery/3_1347551813.jpg
  20. Replies
    56
    Views
    25,521

    HEI ignition conversion

    Hi people

    just to let you know that a GM HEI ignition module works nicely , right in place of the stock ECU.
    I just finished a test conversion, the car started immediately, I didn't even have to...
  21. Replies
    25
    Views
    10,634

    I used the existing stop-bolt on the clutch pedal...

    I used the existing stop-bolt on the clutch pedal pivot, with a short bracket. see pic below; just right of the pedal itself. it works fine, just touch the pedal and it disengages without shifting or...
  22. Replies
    25
    Views
    10,634

    Hi Here is my own "how-to" : ...

    Hi
    Here is my own "how-to" : http://delorean.fr/forum/viewtopic.php?p=28831#28831
    it's in French but I hope pictures speak by themselves, or you can google-translate.
  23. [Transmission 5-Speed] 13.5 daN.m from the Renault workshop manual. it...

    13.5 daN.m from the Renault workshop manual.
    it recommends using threadlock too.
  24. Replies
    19
    Views
    5,167

    [General] take a look here...

    take a look here
    http://www.pjgrady.co.uk//GenericContent.aspx?PageType=Pilot_Chronology&ShowContent=Pilot_Cars.html
  25. Stainless-Wings, the French Delorean Association ( SW )

    Hello
    You are more than welcome to www.delorean.fr , to discuss with the French Delorean community on our forum :
    http://delorean.fr/forum/index.php

    or get technical how-to's ( mostly in french...
Results 1 to 25 of 28
Page 1 of 2 1 2