FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: rollingzep

Search: Search took 0.00 seconds.

  1. Thread: Ground

    by rollingzep
    Replies
    9
    Views
    1,706

    [Electrical] It is a white/yellow wire coming from ballast...

    It is a white/yellow wire coming from ballast resistor. I was going on memory rather than actually looking.
  2. Thread: Ground

    by rollingzep
    Replies
    9
    Views
    1,706

    [Electrical] Thank you Ron. No that isn’t a photo of my setup....

    Thank you Ron. No that isn’t a photo of my setup. I have it wired correctly. I just saw that there was a ground wire cut and wasn’t sure where it went. After many MANY YEARS years and long...
  3. Thread: Ground

    by rollingzep
    Replies
    9
    Views
    1,706

    [Electrical] And one other quick question. I see on the wiring...

    And one other quick question. I see on the wiring schematics that on the coil there is a yellow wire that goes to the positive side of the coil. My wiring only has a white/slate wire on the -side and...
  4. Thread: Ground

    by rollingzep
    Replies
    9
    Views
    1,706

    [Electrical] I circled with red the area I am talking about....

    I circled with red the area I am talking about. And yes it’s by cylinder 4. 62995
  5. Thread: Ground

    by rollingzep
    Replies
    9
    Views
    1,706

    [Electrical] Ground

    I’m in the middle of trying to get my car started after a very long time. Some wires were cut. I found where most of them went but I am not seeing where a few grounds go. Underneath the ballast...
  6. Replies
    1
    Views
    721

    [Electrical] Distributor connection question

    I am putting back the wiring harness on my project car and I have a quick question. Does the distributor wire plug into the wire that goes through the bulkhead by the resistor ballasts? Thank you for...
  7. Thread: Cam timing

    by rollingzep
    Replies
    10
    Views
    9,752

    [General] The cams I am getting are a set of DPI camshafts....

    The cams I am getting are a set of DPI camshafts. So does anyone have any experience with those?
  8. Thread: Cam timing

    by rollingzep
    Replies
    10
    Views
    9,752

    [General] Thank you guys. I had a workshop manual that I...

    Thank you guys. I had a workshop manual that I purchased from PJ Grady back in 1998 that I have no idea where it is now. But those links are most helpful. Can’t wait to get motor running. One...
  9. Thread: Cam timing

    by rollingzep
    Replies
    10
    Views
    9,752

    [General] Cam timing

    I used to have the workshop manual but can’t find it anymore. I will be installing cams in my motor that I have been rebuilding. What is the best way to set up cam timing? Motor is at TDC right...
  10. Replies
    21
    Views
    26,416

    [General] And remember it only has value if you’re...

    And remember it only has value if you’re willing to sell. No sale no value. I have been owner of my cars since a teenager still have my first car I ever bought 69 pace car back in 1995 when it was...
  11. Replies
    21
    Views
    26,416

    [General] Andrew thank you for your post Many years ago...

    Andrew thank you for your post

    Many years ago I also had a Delorean that left me stranded at the worst opportune times like on the middle of a bridge in Manhattan. Not fun let me tell you. I have...
  12. Replies
    21
    Views
    26,416

    [General] I didn’t want this to become a resale value or...

    I didn’t want this to become a resale value or a carb is better than k-jet. The reason I am even going different route cause I don’t have the k jet setup and I used to have a Delorean 20 years...
  13. Replies
    21
    Views
    26,416

    [General] Carb manifold

    Any way I can get in touch with mr bill Robertson to make me an intake or does anyone have any leads on acquiring a carb manifold? Thanks in advance
  14. Replies
    0
    Views
    4,450

    [Wanted] Missing engine parts

    Looking to find a set of cams and rock arm assembly so I can start finishing putting motor together. I have a lead on rocker arms from a b280e engine. Would those be compatible?
  15. [For Sale] Is this still for sale? I’m definitely...

    Is this still for sale? I’m definitely interested in it
  16. Replies
    13
    Views
    33,677

    I am definitely interested in an LS swap. Don’t...

    I am definitely interested in an LS swap. Don’t know how tranny would hold out
  17. Replies
    13
    Views
    33,677

    It was just an idea. Since car doesn’t have...

    It was just an idea. Since car doesn’t have motor was thinking about what I can put in there.
  18. Replies
    13
    Views
    33,677

    Actually the motor is pretty bullet proof. Yes...

    Actually the motor is pretty bullet proof. Yes there’s a timing belt change but motor is pretty strong and with no issues. It puts out 215 hp and propelled esprit to60 in 5 seconds. And in later...
  19. Replies
    13
    Views
    33,677

    Lotus engine swap

    I happen to have a spare 910 HCI motor from an 87 esprit. I was wondering if the motor will bolt right up to the Renault tranny. Has anyone ever done that? I have an 81 without a motor and looking to...
  20. thanks Josh. I emailed you all info. hope you...

    thanks Josh. I emailed you all info. hope you are well
  21. I am having same problem. Cant seem to get a...

    I am having same problem. Cant seem to get a hold of Josh. Josh if you see this message, this is Billy from CT. please give me a call back
Results 1 to 21 of 21