FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Bitsyncmaster

Page 1 of 20 1 2 3 4

Search: Search took 0.21 seconds.

  1. Replies
    11
    Views
    236

    [Engine] The Volvo unit I use will connect right up to...

    The Volvo unit I use will connect right up to stock hoses and electrical connector but it is a smaller diameter so will not bolt up to the stock bracket. I don't use any bracket and it stays put...
  2. Replies
    11
    Views
    236

    [Engine] With your idle switch disconnected you get...

    With your idle switch disconnected you get ignition advance at idle on a warm engine which is why your idle RPM is higher.

    Since your not running the lambda my guess is your idle motor is sticky...
  3. [Electrical] Not talking about any ground in past reference. ...

    Not talking about any ground in past reference. I assume your alternator has a good ground via the mounting bolts. I was taking about the +12 reference that the regulator uses to provide the...
  4. [Electrical] Yes the alternator regulates the voltage...

    Yes the alternator regulates the voltage internally in the alternator. There is an external connection to remotely sense where the voltage reference it uses but most just leave it open and it uses...
  5. Replies
    9
    Views
    300

    [Engine] If you never pulled the intake off, just do it...

    If you never pulled the intake off, just do it now. With it off there is no problem from the top and then you can clean your valley.
  6. Replies
    8
    Views
    229

    Yes both should go on when either door is open...

    Yes both should go on when either door is open when switched to auto on the dome lights. With the OEM dome unit and incandescent bulbs in the domes then there is a delay turning off when both doors...
  7. Replies
    8
    Views
    229

    The diodes don't have anything to do with...

    The diodes don't have anything to do with lighting the door lights. Those diodes are just to drive the dome lights when either door is open. Test that your door light socket has 12 volts on one...
  8. [Electrical] Sounds like you have a bad power connection...

    Sounds like you have a bad power connection somewhere. One common problem are the two feed through 12 volt and ground in the back of the relay compartment. You have to drop the rear plywood board...
  9. [Suspension] I did the "shade-tree" setting for my front toe...

    I did the "shade-tree" setting for my front toe after replacing the parts. If you have to little toe in you won't like highway driving because it's a constant moving of the steering just to go...
  10. Replies
    23
    Views
    770

    [General] I've been thinking about PWM power for the fuel...

    I've been thinking about PWM power for the fuel pump for quite a while. I think when I go EFI I can run without a return line. With Kjet you still need the return line because of the FV needs it.
  11. Replies
    23
    Views
    770

    [General] Running at idle speed causing the buzzing just...

    Running at idle speed causing the buzzing just confirms most of heating is due to the return line. At idle you get the most returned fuel.
  12. Replies
    23
    Views
    770

    [General] When I was running the original type pump, I put...

    When I was running the original type pump, I put a temp sensor if the feed line at the tank and the return line at the tank. My pump would buzz when the feed line hit 130 deg. F. The return line...
  13. Replies
    0
    Views
    142

    [Electrical] Damage to fuse connectors

    DO NOT STICK YOUR METER PROBES INTO FUSE CONNECTORS.

    That goes for any connector pins. Some time ago I got a returned fan fail unit for overheat warning. I tested the voltage drop and it was...
  14. Replies
    9,006
    Views
    2,430,066

    [General] Well I ohm tested the otterstat and read 164 ohms...

    Well I ohm tested the otterstat and read 164 ohms but then test it again and it reads up to 474 ohms. I do have a new one that tests infinity for ohms. I may just leave the otterstat disconnected...
  15. Replies
    9,006
    Views
    2,430,066

    [General] When to take the D to the post office and my...

    When to take the D to the post office and my cooling fans turned when I started the car. The AC was not set on. After a little troubleshooting it looks like my otterstat has failed closed. Just...
  16. Replies
    60
    Views
    116,439

    Sticky: Remove those clips for net and it will drop off.

    Remove those clips for net and it will drop off.
  17. Replies
    5
    Views
    351

    [General] One of these days, I was thinking of 3D printing...

    One of these days, I was thinking of 3D printing the door pulls because I think I can design the inside structure to reduce the weight. You could print in black resin and not have to cover it.
  18. [Fuel] If the dwell reads 0 then the ECU is bad or your...

    If the dwell reads 0 then the ECU is bad or your meter is not reading correct. The minimum dwell the Lambda can set if about 10 deg. Now since you get a buzz pressing the WOT that says your lambda...
  19. [Electrical] What is your voltage with no loads at idle and...

    What is your voltage with no loads at idle and above 2000 RPM? You can read that voltage from the lighter socket. Since no loads all 12 volt and ground connections should be about the same.
  20. [Electrical] As long as your problem is consistent, you can...

    As long as your problem is consistent, you can use a voltmeter with a longer test lead to find voltage drops. First would be to confirm the alternator is producing voltage (about 14.5 volts). So...
  21. Replies
    43
    Views
    2,774

    [Engine] Brake bleeders are the same. They pull air...

    Brake bleeders are the same. They pull air through the threads so you never get the "no bubbles".
  22. You set it so you don't get ice build up on the...

    You set it so you don't get ice build up on the evaporator. So if your AC keeps cold and you are seeing condensation dripping then your probably good as is. If you seem to loose cooling and after...
  23. [Engine] I was hoping that test of the deceleration valves...

    I was hoping that test of the deceleration valves would solve the problem. Anyway it reinforces that problem shows up when you see bad springs. I can loan you one of my idle ECUs if you pay for...
  24. Replies
    24
    Views
    3,693

    [Engine] Try hot gluing the deceleration valve closed.

    Try hot gluing the deceleration valve closed.
  25. Replies
    24
    Views
    3,693

    [Engine] Yes the ECU will think the engine is hot with...

    Yes the ECU will think the engine is hot with that jumper. If it does not close than I would suspect the idle motor is damaged on the valve.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4