FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com

Search:

Type: Posts; User: Ron

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    7
    Views
    549

    [Electrical] Maybe this from the Resources Section...

    Maybe this from the Resources Section will help:

    https://dmctalk.org/attachment.php?attachmentid=92&d=1306264512
  2. Replies
    2
    Views
    376

    [For Sale] Please post the Location.

    Please post the Location.
  3. Replies
    25
    Views
    3,355

    I agree that you should always check the dwell...

    I agree that you should always check the dwell after changing injectors. To get it running so you can, try a shot of starting fluid under the air plate. If no luck, put an spare plug wire in the coil...
  4. Replies
    56
    Views
    29,026

    [General] Yes, as long as you insulate the joint...

    Yes, as long as you insulate the joint afterwards...:smile:
  5. Replies
    25
    Views
    3,355

    Swapping the two plugs is one of the tests to...

    Swapping the two plugs is one of the tests to check the TTS. (It sends power to the cold start valve.) The engine temperature sensor has nothing to do with the cold start valve (its for the gauge...
  6. Replies
    6
    Views
    1,618

    [Wanted] Missing post(s)? Please review the Sticky, ***...

    Missing post(s)?

    Please review the Sticky, *** SECTION RULES *** Please READ BEFORE POSTING ***
  7. Replies
    5
    Views
    1,045

    Try swapping the injectors you suspect are bad...

    Try swapping the injectors you suspect are bad over to cylinders you think are good...
  8. Replies
    3
    Views
    538

    [Transmission Auto] https://dmctalk.org/showthread.php?19806-Governor-...

    https://dmctalk.org/showthread.php?19806-Governor-Crazy&p=277602&viewfull=1#post277602
  9. Replies
    795
    Views
    93,910

    Assuming the pic shows right before you tried to...

    Assuming the pic shows right before you tried to install it, try loading the piston into the lower half of the ring compressor instead of the top half...Soak with oil first.
  10. Replies
    5
    Views
    2,743

    Down under where you enter your username and...

    Down under where you enter your username and password there is a checkbox labeled "Remember Me?"...
    If you select it, you should stay logged in until the browser is cleared.
  11. Replies
    27
    Views
    3,056

    [General] +1

    +1
  12. Thread: Governor Crazy

    by Ron
    Replies
    51
    Views
    5,553

    [Transmission Auto] Need a bit of clarification here... When you said...

    Need a bit of clarification here... When you said it was "leaking oil near the torque converter seal...", did you mean gear oil or automatic transmission fluid? I was assuming Automatic transmission...
  13. Thread: Governor Crazy

    by Ron
    Replies
    51
    Views
    5,553

    [Transmission Auto] "Permatex High Temperature Sleeve Retainer...

    "Permatex High Temperature Sleeve Retainer is a high temperature anaerobic adhesive that secures slip and press fit assemblies and restores fit to worn or out-of-tolerance assemblies. This adhesive...
  14. Thread: Governor Crazy

    by Ron
    Replies
    51
    Views
    5,553

    [Transmission Auto] I agree, it wasn't temp nor too much fluid. He...

    I agree, it wasn't temp nor too much fluid.
    He should of used a high temp sleeve retainer and the correct installation tool, imho.
  15. +1 :thumbup:

    +1 :thumbup:
  16. [General] ^+1^ The Lambda counter is also a good place...

    ^+1^

    The Lambda counter is also a good place to start checking to see if the cable is at fault. Rather than top to bottom, divide and conquer...jack the left front up, spin the wheel and see if...
  17. Replies
    12
    Views
    1,152

    [Suspension] I agree, it's not that bad. Trim the high spots...

    I agree, it's not that bad. Trim the high spots off and taper the end a bit. Then chase the threads from the good to the bad as mentioned and you'll be good to go.
  18. Replies
    12
    Views
    1,152

    [Suspension] That would be ok if the damage will allow the...

    That would be ok if the damage will allow the tool to get started straight and smoothly.

    Sorry, I fixed the link. Works best for me, especially if the lead threads are smashed...
  19. Replies
    12
    Views
    1,152

    [Suspension] Try a thread chaser (Pitches 0.75, 1.0, 1.25,...

    Try a thread chaser (Pitches 0.75, 1.0, 1.25, 1.5, 1.75, 2.0, 2.5, 3.0mm on Amazon).
  20. Thread: failed smog

    by Ron
    Replies
    129
    Views
    10,057

    [General] FWIW- If is was an auto, I would of suggested...

    FWIW- If is was an auto, I would of suggested checking its vacuum line for leaks/sucking fluid...

    Bad oil can definitely make it fail...if during the 500 miles it was running way rich (or anything...
  21. Thread: failed smog

    by Ron
    Replies
    129
    Views
    10,057

    [General] WTH??? ...We don't have to deal with the tests...

    WTH???
    ...We don't have to deal with the tests here, but if I'm reading them right, it looks like everything for high RPM is worse while the low RPM is better than the 8/30 test now (after replacing...
  22. Replies
    15
    Views
    1,039

    [Transmission Auto] YW!

    YW!
  23. Replies
    15
    Views
    1,039

    [Transmission Auto] I think you may be missing that the solenoids are...

    I think you may be missing that the solenoids are wired hot (12V) at all times. (They are ground controlled -- Pull the fuse and it is in 3rd!)
    ...The GC grounds a solenoid to turn it on, forcing a...
  24. Replies
    15
    Views
    1,039

    [Transmission Auto] Maybe this will help... Basically, shifting is...

    Maybe this will help...

    Basically, shifting is done using two solenoids (to open and close two valves). They are controlled by the "computer governor" (GC), which receives input from a signal...
  25. Replies
    15
    Views
    1,039

    [Transmission Auto] FWIW: "INCORRECT GEAR CHANGING SPEEDS" 4, 5,...

    FWIW:
    "INCORRECT GEAR CHANGING SPEEDS" 4, 5, ...
    4) Accelerator Controls
    5) Governor Cable
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4