FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11

Thread: LOTS of Engine Parts For Sale

  1. #1
    Junior Member
    Join Date:  Feb 2012

    Location:  Goodyear, AZ

    Posts:    9

    My VIN:    SCEDT26T4BD002955

    LOTS of Engine Parts For Sale

    Hello fellow DMCers,

    I have a lot of engine parts for sale. Most of these came off of a running motor with bad cylinder liners. I replaced the motor with a B28F out of a volvo and have a lot of extra parts.

    I live in Bloomington, IL
    You can contact me at: [email protected]
    Prices I believe are fair (25% to 75% below new) and most are negotiable.

    Block (upper crankcase-cylinder liners removed) Part #:102001 $400

    Crankshaft (will come with timing and oil pump sprockets. Will need machined/turned) $300
    Crankshaft pulley nut. Part #:102474 $10
    Pistons and connecting rods (6) (NOTE: pistons are probably NOT good, but the connecting rods are). $50 each connecting rod (will come with a piston)
    Head (rebuilt, only 200 miles. Off running motor) 4,5,6 (loaded with valves) Part #:102157 $400
    Head (rebuilt, only 200 miles. Off running motor) 1,2,3 (loaded with valves) Part #:102173 $400
    Cam Shaft 1,2,3 (Passenger) Part #:102707 $100
    Cam Shaft 4,5,6 (Driver) Part #:102706 $100
    Rocker Arm Assembly (1,2,3) $150
    Rocker Arm Assembly (4,5,6) $150
    Timing Chain 1,2,3 Part #:102214 $10
    Timing Chain 4,5,6 Part #:102214 $10
    Timing Sprocket 1,2,3 Part #: 102209 $20
    Timing Sprocket 4,5,6 Part #: 102209 $20
    Timing chain tensioner kit 1,2,3 Part #:102605 $75
    Timing chain tensioner kit 4,5,6 Part #:102605 $75
    Oil pump and sprocket Part #:102622 $100
    Oil pump drive chain Part #:102229 $30
    Driver side valve cover Part #:102252 $75
    Timing cover Part #:102192 $100
    Intake Part #:102260 $200
    Tubes, throttle/manifold (Bull horns) Part #:102279 $150
    Mixture control unit Part #:102789 $200
    Mixture control lower housing Part #:102771 -- (NOTE, This unit has a modification where the idle air motor tube goes. It is probably a better than stock design, but still not stock. It has a welded nipple so you can slide the air hose right on. I can take a picture if you want). $75


    Throttle Butterfly assembly Part #:102856 $40
    Fuel Distributor Part #:102807 $200
    Ignition distributor Part #:102751 -- (some of the plastic on the plug is gone, but it still plugs in and works. It came off a running motor). $150

    Idle air motor (untested) Part #:102502 $100
    Fuel injectors (I have 12) Part #:102742 $25 each
    Cold start tube Part #:102374 $40
    Cold Start Injector Part #:102372 $50
    Rear main seal housing. Part #:102023 $30
    Warm up regulator (untested) Part #:102353 $60
    Exhuast Manifold 1,2,3 Part #:102258 $150
    Exhaust Manifold 4,5,6 Part #:102257 $150

  2. #2
    "Former Delorean owning Guru" Spittybug's Avatar
    Join Date:  Jun 2011

    Location:  Hill Country, TX

    Posts:    1,579

    My VIN:    Formerly 2329

    As a magnanimous gesture, what about a consignment "loan" to AdmiralSenn (Adam) of a head so that he can get his car sold in running condition? I'm not brokering this, merely suggesting there may be some goodwill to be extended until he can sell the car..................... just an idea.
    Owen
    I.Brew.Beer.

  3. #3
    Cock Monger thirdmanj's Avatar
    Join Date:  May 2011

    Posts:    2,517

    Quote Originally Posted by Spittybug View Post
    As a magnanimous gesture, what about a consignment "loan" to AdmiralSenn (Adam) of a head so that he can get his car sold in running condition? I'm not brokering this, merely suggesting there may be some goodwill to be extended until he can sell the car..................... just an idea.
    Hear hear!!

  4. #4
    Administrator Ron's Avatar
    Join Date:  Jun 2011

    Location:  North GA

    Posts:    6,190

    Club(s):   (SEDOC) (DCUK)

    Looks like you may have 90% of the fasteners etc I need if you are going to break it all up.
    http://dmctalk.org/showthread.php?4534-Misc-Banjo-Bolts-Fuel-Fittings PM me...

  5. #5
    Junior Member
    Join Date:  Feb 2012

    Location:  Goodyear, AZ

    Posts:    9

    My VIN:    SCEDT26T4BD002955

    Spittybug...perhaps I will message AdmiralSenn.



    Quote Originally Posted by Spittybug View Post
    As a magnanimous gesture, what about a consignment "loan" to AdmiralSenn (Adam) of a head so that he can get his car sold in running condition? I'm not brokering this, merely suggesting there may be some goodwill to be extended until he can sell the car..................... just an idea.

  6. #6
    Member seventy4burban's Avatar
    Join Date:  Aug 2011

    Location:  Bluffton, South Carolina

    Posts:    82

    My VIN:    11326

    You don't have an oil pan by chance do you. I am in serious need!
    Brian
    Bluffton, South Carolina

    My toys
    2019 Dodge Challenger Widebody SCAT Pack
    2010 Chevy Silverado 2500HD
    1982 Delorean DMC-12
    1974 Chevy Suburban

  7. #7
    Junior Member
    Join Date:  Feb 2012

    Location:  Goodyear, AZ

    Posts:    9

    My VIN:    SCEDT26T4BD002955

    oil pan.

    I don't have an oil pan. sorry!

    Quote Originally Posted by seventy4burban View Post
    You don't have an oil pan by chance do you. I am in serious need!

  8. #8
    Junior Member
    Join Date:  Feb 2012

    Location:  Goodyear, AZ

    Posts:    9

    My VIN:    SCEDT26T4BD002955

    bump

    Bumping post. Cam Shafts and Warm Up Regulator are sold.

    Quote Originally Posted by ltemup4650 View Post
    Hello fellow DMCers,

    I have a lot of engine parts for sale. Most of these came off of a running motor with bad cylinder liners. I replaced the motor with a B28F out of a volvo and have a lot of extra parts.

    I live in Bloomington, IL
    You can contact me at: [email protected]
    Prices I believe are fair (25% to 75% below new) and most are negotiable.

    Block (upper crankcase-cylinder liners removed) Part #:102001 $400
    Crankshaft (will come with timing and oil pump sprockets. Will need machined/turned) $300
    Crankshaft pulley nut. Part #:102474 $10
    Pistons and connecting rods (6) (NOTE: pistons are probably NOT good, but the connecting rods are). $50 each connecting rod (will come with a piston)
    Head (rebuilt, only 200 miles. Off running motor) 4,5,6 (loaded with valves) Part #:102157 $400
    Head (rebuilt, only 200 miles. Off running motor) 1,2,3 (loaded with valves) Part #:102173 $400
    Rocker Arm Assembly (1,2,3) $150
    Rocker Arm Assembly (4,5,6) $150
    Timing Chain 1,2,3 Part #:102214 $10
    Timing Chain 4,5,6 Part #:102214 $10
    Timing Sprocket 1,2,3 Part #: 102209 $20
    Timing Sprocket 4,5,6 Part #: 102209 $20
    Timing chain tensioner kit 1,2,3 Part #:102605 $75
    Timing chain tensioner kit 4,5,6 Part #:102605 $75
    Oil pump and sprocket Part #:102622 $100
    Oil pump drive chain Part #:102229 $30
    Driver side valve cover Part #:102252 $75
    Timing cover Part #:102192 $100
    Intake Part #:102260 $200
    Tubes, throttle/manifold (Bull horns) Part #:102279 $150
    Mixture control unit Part #:102789 $200
    Mixture control lower housing Part #:102771 -- (NOTE, This unit has a modification where the idle air motor tube goes. It is probably a better than stock design, but still not stock. It has a welded nipple so you can slide the air hose right on. I can take a picture if you want). $75


    Throttle Butterfly assembly Part #:102856 $40
    Fuel Distributor Part #:102807 $200
    Ignition distributor Part #:102751 -- (some of the plastic on the plug is gone, but it still plugs in and works. It came off a running motor). $150

    Idle air motor (untested) Part #:102502 $100
    Fuel injectors (I have 12) Part #:102742 $25 each
    Cold start tube Part #:102374 $40
    Cold Start Injector Part #:102372 $50
    Rear main seal housing. Part #:102023 $30
    Exhuast Manifold 1,2,3 Part #:102258 $150
    Exhaust Manifold 4,5,6 Part #:102257 $150

  9. #9
    Senior Member AugustneverEnds's Avatar
    Join Date:  Jul 2012

    Location:  Syracuse, NY area

    Posts:    1,047

    My VIN:    10287

    Club(s):   (DMA)

    Hi, you wouldn't happen to have the gaskets and studs with the exhaust manifolds by any chance?
    Nick A.

    1988 BMW 325is
    1982 DeLorean DMC-12
    1989 Jaguar XJ6

  10. #10
    Junior Member
    Join Date:  Feb 2012

    Location:  Goodyear, AZ

    Posts:    9

    My VIN:    SCEDT26T4BD002955

    Exhaust

    I have the studs but no gaskets...why would you want used gaskets? These are cheap from part stores. Look them up on Rockauto.com $22 per side.

    BECK/ARNLEY Part # 0374630

    Use 1983 Volvo 760 with 2.8 as a search vehicle.

    Quote Originally Posted by AugustneverEnds View Post
    Hi, you wouldn't happen to have the gaskets and studs with the exhaust manifolds by any chance?

Page 1 of 2 1 2 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •