FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 2 of 6 FirstFirst 1 2 3 4 ... LastLast
Results 11 to 20 of 60

Thread: DeLorean Ground Schematic

  1. #11
    Senior Member WelmoedJ's Avatar
    Join Date:  Jun 2011

    Location:  Purmerend, Netherlands

    Posts:    747

    My VIN:    06513

    Club(s):   (DCN)

    Bill,

    There's a ground wire behind the panel that covers the fuel fill hoses.
    The wire is attached to a bolt that runs through the "firewall" and connects to the pedal box.
    I have traced this wire to be the ground for the fuel sender.

    Welmoed.
    Welmoed
    Black D 1981-11 sold
    Toyota Prius III 2009-07 (sold)
    Mazda MX-30 (BEV) 2020-09

  2. #12
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,636

    My VIN:    03572

    Yes it's just the dash volt gauge that sees that ground offset caused by the fuel pump current (and now maybe the blower current) that makes it read lower. What your doing with the large ground buss should fix it. But my plan is just to make those two large current grounds move to the frame. Then the original ground wire only has to conduct the light ground currents and hence not offset the dash gauge.

    I have already put the inertia switch ground to it's own frame ground. Now I will move the blower ground to it's own frame ground. I would do the same, run a 10 AWG wire to the shifter mount bolt. This should increase the blower motor voltage a little also.

    edit:

    Actually all the dash gauges are seeing the offset but it seems the most affected gauge is the volt gauge.
    Last edited by Bitsyncmaster; 08-25-2011 at 06:20 AM.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  3. #13
    Senior Member
    Join Date:  May 2011

    Location:  Staten Island, NY

    Posts:    256

    My VIN:    3501

    Club(s):   (DMA)

    If it helps I have my video of the wire harness breakdown here:

    http://youtu.be/_IND69PZ6C4

  4. #14
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    While poking around under #5939's dash I realized a few errors from the front junction. This is a corrected copy:
    DeLoreanGroundsInProcess4.jpg

    I still hope to trace out the relay compartment grounds later today.

    Bill Robertson
    #5939

  5. #15
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,636

    My VIN:    03572

    Quote Originally Posted by content22207 View Post
    While poking around under #5939's dash I realized a few errors from the front junction. This is a corrected copy:
    DeLoreanGroundsInProcess4.jpg

    I still hope to trace out the relay compartment grounds later today.

    Bill Robertson
    #5939
    So the headlights go back to the harness ground? Wonder why they did not use the frame ground like the fans.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  6. #16
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    The headlights (and side/front marker lights) go directly to the bulkhead bolt, thence to the frame.

    Bill Robertson
    #5939

  7. #17
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Great work Bill. A suggestion if I may...

    Put a pass-through of the inertia switch with perhaps a dashed line leading through the washer bottle connectors to the fuel pump. Its an important enough circuit I feel the complete path should be mapped.
    Jim Reeve
    DMC6960

  8. #18
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    Purple/Black is a switched ground. It's no different in principle than Purple/White. This schematic shows black wires only. Any wire you ring out on this schematic should beep to the negative battery terminal.

    Bill Robertson
    #5939

  9. #19
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    As a world renown Nazarene once said, it is finished:
    DeLoreanGroundsFinal1.jpg

    Actually I have labeled this file "Final1" because there are still at least three unknowns/assumptions subject to change:

    1) The large gauge wire from the junction behind the A/C central duct is assumed to be the the windshield wiper motor -- until I figure out where the damn thing is and can visually verify it, that is subject to change. The second large gauge most likely is the inertia switch because it has the same gauge wire attached. The third large gauge wire was verified all the way back to the bulkhead bolt by unwrapping the harness. I unfortunately can not unwrap the harness forward to trace the other two large gauge wires because it disappears between a metal superstructure and the dash.

    2) The small gauge wire to the wiper delay module continue somewhere (annoying door buzzer perhaps?). I do not have annoying door buzzers in either of my cars, so I can't verify that.

    3) The small gauge wire that disappears by the windshield is assumed to be the wire that emerges from underneath the windshield trim and is attached to the fender -- I haven't pulled the trim off yet to verify.

    All other wires were visually verified by unwrapping the harness and following them to see where they go. I am now the proud possessor of a DeLorean with no front suspension (or condensor/radiator/fans), no fuel delivery system, no interior, *AND* a whole lot of loose wires. Anybody want to come over with a couple rolls of electrical tape and help me put this thing back together?

    So there you have it. The next time someone laments that they have no idea where something is grounded on these stupid little cars, just point them to this thread.

    Bill Robertson
    #5939

  10. #20
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    Well that didn't last long....

    First revision:
    - Redraw glove box switch and passenger door plunger to more clearly represent that the wires are ganged
    - Change "Useless Bolt" to "Dashboard Bolt" (I was hot, tired, and irritable when I wrote that)
    - Add sidelights to the *ONE* 16 gauge ground wire from the back of the car (what was Lotus thinking?)

    DeLoreanGroundsFinal2.jpg

    Bill Robertson
    #5939

    DMCTalk is automatically downsizing my original (1300 x 1600 pixels). If you want a larger copy, shoot me your eMail address.

    Bill Robertson
    #5939

Page 2 of 6 FirstFirst 1 2 3 4 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •