FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 5 of 6 FirstFirst ... 3 4 5 6 LastLast
Results 41 to 50 of 60

Thread: DeLorean Ground Schematic

  1. #41
    Senior Member AdmiralSenn's Avatar
    Join Date:  May 2011

    Posts:    443

    Quote Originally Posted by Farrar View Post
    Gas cylinder: $11. Soldering/brazing torch: $35. Battery crimp tool: $231.

    Soldering method looks a lot better to my wallet.

    Farrar
    I bought a propane cylinder with head and a decent sized tank for ~$25, and honestly you can get away with a regular crimper and brute force. Alternately you could use a bench vise - not sure how much they are but I know there are crimping tools you can put in a vise.

    I just used a set of regular wire stripper/crimpers. One terminal I couldn't quite get crimped enough so I stuck it in the corner of the vise and pinched it a little farther.

    Don't really need anything fancy for this particular job.

    Alternately you could probably rent or borrow a battery crimp tool from advance or whatever's closest.

    Trust me this job is well worth it, just for the peace of mind.

  2. #42
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by AdmiralSenn View Post
    Alternately you could probably rent or borrow a battery crimp tool from advance or whatever's closest.
    There's an idea -- I hadn't thought that such a thing might be one of the loaner tools available from a parts house. Thanks!

    Farrar
    3.0L, automatic, carbureted

  3. #43
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,395

    My VIN:    5003 Never placed Concourse 2002-Current

    Club(s):   (DCF)

    If you go to Lowes or Home Depot, they have the small propane cylinders or [my preference] MAPP gas cylinders. These cylinders are cheap.

  4. #44
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    Without a proper crimping tool you're going to be just as well off with solder alone. Be sure to flux the connector so the solder will stick.

    Bill Robertson
    #5939

  5. #45
    Administrator Ron's Avatar
    Join Date:  Jun 2011

    Location:  North GA

    Posts:    6,200

    Club(s):   (SEDOC) (DCUK)

    Body Bonding?

  6. #46
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    Static electricity dissipation.

    Bill Robertson
    #5939

  7. #47
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    I could probably attempt crimping with a blunt cold chisel and a sledgehammer, but I think soldering will be the way to go, once I have the money and time. In the meantime, I am going to run a 10-gauge ground wire from that bundle behind the gauge cluster to the nearest body bolt, ensuring that my inertia switch has a good ground; I am tired of dead fuel pumps making we walk home.

    Farrar
    3.0L, automatic, carbureted

  8. #48
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    12 gauge would be adequate. Just cut the ground wire at the switch and tie your new ground to it there. The inertia switch is *MUCH* more accessible than that junction (at least without tearing half the car apart).

    Have you been melting fuse #7? If so, your pump ground is indeed likely below par.

    Bill Robertson
    #5939

  9. #49
    Administrator Ron's Avatar
    Join Date:  Jun 2011

    Location:  North GA

    Posts:    6,200

    Club(s):   (SEDOC) (DCUK)

    Quote Originally Posted by content22207 View Post
    Static electricity dissipation.

    Bill Robertson
    #5939
    Sorry, I meant where does it connect. I found several braided grounds exposed while cleaning up and replacing seals etc. Thought you might want the locations for completeness.

  10. #50
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    Only connection I found inside the passenger compartment was through the passenger side of the car, directly below the windshield, to one of the dashboard studs, thence to the blower motor (the negative side of the blower motor has three posts, which DMC used as a junction point). There is no wire in that location on the driver's side.

    Bill Robertson
    #5939

Page 5 of 6 FirstFirst ... 3 4 5 6 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •